REMOVAL
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for 2GR-FE RHD)
|
 |
- Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 2.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (except 2GR-FE RHD) |
 |
for Automatic Transaxle LHD: (Click here)for Automatic Transaxle RHD: (Click here)for Manual Transaxle RHD: (Click here)
| 3.
REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (except 2GR-FE RHD)
|
 |
- Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.
| 4.
REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (except 2GR-FE RHD)
|
 |
- Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.
| 5.
REMOVE POSITION INDICATOR HOUSING ASSEMBLY (except 2GR-FE RHD) |
 |
for Automatic Transaxle LHD: (Click here)for Automatic Transaxle RHD: (Click here)
| 6.
REMOVE UPPER CONSOLE PANEL (except 2GR-FE RHD) |
 |
for Manual Transaxle RHD: (Click here)
| 7.
REMOVE UPPER CONSOLE PANEL FRONT GARNISH (for 2GR-FE RHD)
|
 |
- Apply protective tape to the area shown in the illustration.
- Using a moulding remover, disengage the 3 claws as shown in the illustration.
- Using a moulding remover, disengage the 3 claws and remove the upper console panel front garnish as shown in the illustration.
Disconnect each connector.
| 8.
REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (except 2GR-FE RHD) |
 |
for Automatic Transaxle LHD: (Click here)for Automatic Transaxle RHD: (Click here)for Manual Transaxle RHD: (Click here)
| 9.
REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (for 2GR-FE RHD)
|
 |
- Apply protective tape to the area shown in the illustration.
- Using a moulding remover, disengage the 2 claws as shown in the illustration.
- Apply protective tape to the area shown in the illustration.
- Using a moulding remover, disengage the 2 claws as shown in the illustration.
- Disengage the 6 claws and remove the upper console panel sub-assembly as shown in the illustration.
Disconnect the connector.
| 10.
REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (except 2GR-FE RHD)
|
 |
- Remove the 2 screws <F>.
Disengage the 4 claws.
Disconnect each connector and remove the upper console panel sub-assembly.
- HINT:
- Set the shift lever in the D position.
| 11.
REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY (except 2GR-FE RHD)
|
 |
- Apply protective tape to the areas shown in the illustration.
- Using a moulding remover, disengage the 3 clips.
- Using a moulding remover, disengage the 4 clips.
Disconnect the connector and remove the instrument panel No. 2 register assembly.
| 12.
REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY (for 2GR-FE RHD)
|
 |
- Apply protective tape to the areas shown in the illustration.
- Using a moulding remover, disengage the 6 claws as shown in the illustration.
- Using a moulding remover, disengage the 5 claws as shown in the illustration.
Disconnect each connector and remove the instrument panel No. 2 register assembly.
| 13.
REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (for Radio Receiver Type)
|
 |
- Remove the 4 bolts.
Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the radio receiver with heater control panel assembly.
| 14.
REMOVE RADIO AND DISPLAY WITH HEATER CONTROL PANEL ASSEMBLY (for Radio and Display Type)
|
 |
- Remove the 4 bolts.
Pull the radio and display with heater control panel assembly toward the rear of the vehicle and disengage the 6 clips.
Disconnect each connector and remove the radio and display with heater control panel assembly.
| 15.
REMOVE NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System)
|
 |
- Remove the 4 bolts.
Pull the navigation receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the navigation receiver with heater control panel assembly.
| 16.
REMOVE RADIO NO. 1 BRACKET (for Radio Receiver Type)
|
 |
- Remove the 3 bolts, 2 screws and radio No. 1 bracket.
| 17.
REMOVE RADIO NO. 1 BRACKET (for Radio and Display Type)
|
 |
- Remove the 4 bolts, 2 screws, radio receiver panel, and radio No. 1 bracket.
| 18.
REMOVE RADIO NO. 1 BRACKET (w/ Navigation System)
|
 |
- Remove the 3 bolts, 2 screws and radio No. 1 bracket.
| 19.
REMOVE RADIO NO. 2 BRACKET (for Radio Receiver Type)
|
 |
- Remove the 3 bolts, 2 screws and radio No. 2 bracket.
| 20.
REMOVE RADIO NO. 2 BRACKET (for Radio and Display Type)
|
 |
- Remove the 4 bolts, 2 screws, radio receiver panel, and radio No. 2 bracket.
| 21.
REMOVE RADIO NO. 2 BRACKET (w/ Navigation System)
|
 |
- Remove the 3 bolts, 2 screws and radio No. 2 bracket.
| 22.
REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Radio Receiver Type) |
 |
- Remove the air conditioning control assembly as shown in the illustration.
| 23.
REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Radio and Display Type) |
 |
- Remove the air conditioning control assembly as shown in the illustration.
| 24.
REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System) |
 |
- Remove the air conditioning control assembly as shown in the illustration.