2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Luggage Compartment Door Key Cylinder Switch Circuit

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

When the luggage compartment door lock cylinder is turned to unlock the door by the key, there is continuity between terminal TSW of the main body ECU (instrument panel J/B) and body ground.

WIRING DIAGRAM

B150880E10

INSPECTION PROCEDURE


1. READ VALUE ON INTELLIGENT TESTER

  1. E138501E01
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select Trunk Lock/Unlock SW in the "DATA LIST" and read the display on the intelligent tester.

    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Trunk Lock/Unlock SW
    Luggage compartment door key cylinder switch / ON or OFF
    ON: Ignition key inserted and turned to lock position
    OFF: Ignition key inserted and turned to unlock position
    -

    OK:
    When the ignition switch is operated, the display changes as shown above.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT MAIN BODY ECU (TSW TERMINAL)

  1. B137943E08
    Turn the ignition switch off.

  1. Disconnect the main body ECU (instrument panel J/B) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    E6-2 (TSW) - Body ground
    Luggage compartment door lock cylinder LOCK
    10 kΩ or higher
    E6-2 (TSW) - Body ground
    Luggage compartment door lock cylinder OPEN
    Below 1 Ω
    E6-2 (TSW) - Body ground
    Luggage compartment door lock cylinder UNLOCK
    10 kΩ or higher



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

3. INSPECT LUGGAGE COMPARTMENT DOOR LOCK CYLINDER

  1. B156772E03
    Disconnect the luggage compartment door lock cylinder connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    with Smart Entry and Start System for RHD:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    S8-1 - S8-3
    Luggage compartment door lock cylinder CENTER
    10 kΩ or higher
    S8-1 - S8-3
    Luggage compartment door lock cylinder CANCEL
    Below 1 Ω
    S8-1 - S8-3
    Luggage compartment door lock cylinder UNLOCK
    10 kΩ or higher
    without Smart Entry and Start System for RHD:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    S6-2 - S6-1
    Luggage compartment door lock cylinder LOCK
    10 kΩ or higher
    S6-2 - S6-1
    Luggage compartment door lock cylinder OPEN
    Below 1 Ω
    S6-2 - S6-1
    Luggage compartment door lock cylinder UNLOCK
    10 kΩ or higher



NG
REPLACE LUGGAGE COMPARTMENT DOOR LOCK CYLINDER
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU, BODY GROUND - DOOR LOCK CYLINDER)


← Luggage Compartment Door Lock Circuit (from Jun 2009)Luggage Compartment Door Key Cylinder Switch Circuit (from Jun 2009) →