2006-2011 Camry Aurion · Service Manual TRANSMISSION

INSPECTION

Inspection · Vehicles built from Jun 2006


INSPECT SHIFT SOLENOID VALVE SL3

  1. G020767E29
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    5.0 to 5.6 Ω

    If the value is not as specified, replace the shift solenoid valve.

  1. Connect the positive (+) lead to terminal 2 of the solenoid connector, and the negative (-) lead to terminal 1 of the solenoid connector.

    OK:
    The solenoid valve makes an operating sound.

    If the result is not as specified, replace the shift solenoid valve.


INSPECT SHIFT SOLENOID VALVE SLT

  1. G020767E08
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    5.0 to 5.6 Ω

    If the value is not as specified, replace the shift solenoid valve.

  1. Connect the positive (+) lead to terminal 2 of the solenoid connector, and the negative (-) lead to terminal 1 of the solenoid connector.

    OK:
    The solenoid valve makes an operating sound.

    If the result is not as specified, replace the shift solenoid valve.


INSPECT SHIFT SOLENOID VALVE S4

  1. C113971E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    Solenoid Connector (S4) - Solenoid Body (S4)
    11 to 15 Ω

    If the value is not as specified, replace the shift solenoid valve.

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid valve makes an operating sound.

    If the result is not as specified, replace the shift solenoid valve.


INSPECT SHIFT SOLENOID VALVE SR

  1. C113977E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    Solenoid Connector (SR) - Solenoid Body (SR)
    11 to 15 Ω

    If the value is not as specified, replace the shift solenoid valve.

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid valve makes an operating sound.

    If the result is not as specified, replace the shift solenoid valve.


INSPECT SHIFT SOLENOID VALVE DSL

  1. C113970E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    Solenoid Connector (DSL) - Solenoid Body (DSL)
    11 to 15 Ω

    If the value is not as specified, replace the shift solenoid valve.

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid valve makes an operating sound.

    If the result is not as specified, replace the shift solenoid valve.


INSPECT SHIFT SOLENOID VALVE SL2

  1. G020767E28
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    5.0 to 5.6 Ω

    If the value is not as specified, replace the shift solenoid valve.

  1. Connect the positive (+) lead to terminal 2 of the solenoid connector, and the negative (-) lead to terminal 1 of the solenoid connector.

    OK:
    The solenoid valve makes an operating sound.

    If the result is not as specified, replace the shift solenoid valve.


INSPECT SHIFT SOLENOID VALVE SL1

  1. G020767E46
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    5.0 to 5.6 Ω

    If the value is not as specified, replace the shift solenoid valve.

  1. Connect the positive (+) lead to terminal 2 of the solenoid connector, and the negative (-) lead to terminal 1 of the solenoid connector.

    OK:
    The solenoid valve makes an operating sound.

    If the result is not as specified, replace the shift solenoid valve.

← DISASSEMBLY (from Jun 2006)REASSEMBLY (from Jun 2006) →