2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

B2326 CAN MS Bus Line Communication Malfunction

Diagnostic trouble codes · Vehicles built from Oct 2006

DESCRIPTION

  1. The main body ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to the CAN MS bus.
  2. When the main body ECU receives response signals from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECUs are connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.
DTC No.
DTC Detection Condition
Trouble Area
B2326
Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus.
  1. Open or short in CAN MS bus main wire
  2. Open or short in CAN MS bus branch wire
  3. Clearance warning ECU
  4. Main body ECU
  5. CAN No. 3 J/C

WIRING DIAGRAM

C142749E07

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.


1. CHECK CAN MS BUS WIRE

  1. C144960E01
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Result:
    Tester Connection
    Condition
    Specified Value
    Proceed to
    O33-1 (CANH) - O33-2 (CANL)
    Ignition switch off
    54 to 69 Ω
    A
    O33-1 (CANH) - O33-2 (CANL)
    Ignition switch off
    69 Ω or higher
    B
    O33-1 (CANH) - O33-2 (CANL)
    Ignition switch off
    Less than 54 Ω
    C



B
Go to step 5

C
Go to step 7
A


2. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE

  1. C144962E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O33-2 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 11
OK


3. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE

  1. C144962E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    O33-2 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 14
OK


4. CHECK FOR OPEN IN CAN MS BUS BRANCH WIRE
  1. Check the clearance warning ECU branch wire (Click here).



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CLEARANCE WARNING ECU)
OK

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)

5. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C)

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

    HINT:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - O33-2 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE CAN NO. 3 J/C
NG


6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C)
  1. Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. C142209E03
    Disconnect connector E8 from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E8-15 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU)
OK

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)

7. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 3 J/C WIRE)

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - O33-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 10
OK


8. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE)
  1. Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. C142740E01
    Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

    HINT:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - O32-2 (CANL)
    Ignition switch off
    1 MΩ or higher



OK
REPLACE CAN NO. 3 J/C
NG


9. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE)

  1. C142740E01
    Disconnect clearance warning ECU connector O30.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - O32-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CLEARANCE WARNING ECU - CAN NO. 3 J/C)
OK

REPLACE CLEARANCE WARNING ECU

10. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C)

  1. C142209E03
    Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. Disconnect connector E8 from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E8-15 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU)
OK

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)

11. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE)

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

  1. C126231E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O33-2 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 13
OK


12. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C)
  1. Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. C145027E01
    Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

  1. Disconnect connector O30 from the clearance warning ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O32-2 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CLEARANCE WARNING ECU BRANCH WIRE)
OK

REPLACE CLEARANCE WARNING ECU

13. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (MAIN BODY ECU - CAN NO. 3 J/C)

  1. C145026E01
    Disconnect the main body ECU connector E8 from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O33-2 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU)
OK

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)

14. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE)

  1. C145026E02
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    O33-2 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 16
OK


15. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C)

  1. C145027E02
    Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

  1. Disconnect connector O30 from the clearance warning ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    O32-2 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CLEARANCE WARNING ECU BRANCH WIRE)
OK

REPLACE CLEARANCE WARNING ECU

16. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (MAIN BODY ECU - CAN NO. 3 J/C)

  1. C145026E02
    Disconnect the main body ECU connector E8 from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    O33-2 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU)
OK

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)


← B1297 Clearance Sonar ECU Communication Stop (from Oct 2006)Skid Control ECU Communication Stop Mode (from Oct 2006) →