2006-2011 Camry Aurion · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Oct 2006


1. BEARING POSITION

  1. Check bearing position and installation direction.

    C162512E01

    C138529E01

    Mark
    Front Race Diameter
    Inside / Outside mm (in.)
    Thrust Bearing Diameter
    Inside / Outside mm (in.)
    Rear Race Diameter
    Inside / Outside mm (in.)
    A
    -
    57.7 (2.271) / 75.2 (2.961)
    -
    B
    -
    29.1 (1.146) / 48.6 (1.913)
    30.7 (1.209) / 48.3 (1.902)
    C
    65.9 (2.594) / 80.3 (3.161)
    62.6 (2.465) / 82.4 (3.244)
    -
    D
    59.4 (2.339) / 77 (3.032)
    53.1 (2.091) / 79 (3.110)
    -
    E
    -
    56.1 (2.209) / 80.9 (3.185)
    -
    F
    -
    61.2 (2.409) / 79 (3.110)
    -
    G
    -
    28 (1.102) / 47.1 (1.854)
    26.1 (1.028) / 44 (1.732)
    H
    52.2 (2.055) / 70.4 (2.772)
    48.9 (1.925) / 72.0 (2.835)
    -


2. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

  1. C137421E01
    Coat the lip of a new manual valve lever shaft oil seal with MP grease.

  1. Using SST and a hammer, install the manual valve lever shaft oil seal to the transaxle case.

    SST
    09950-60010   (09951-00230)
    09950-70010   (09951-07100)

    Oil seal installation depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


3. INSTALL MANUAL VALVE LEVER SHAFT
  1. Install a new spacer to the parking lock lever sub-assembly.

  1. Install the parking lock lever sub-assembly to the manual valve lever shaft.

  1. Install a new spacer to the manual valve lever sub-assembly.

  1. Install the manual valve lever sub-assembly to the manual valve lever shaft.

  1. C137428
    Install the manual valve lever shaft to the transaxle case.

    NOTICE:
    Do not damage the manual valve lever shaft oil seal while installing the manual valve lever shaft to the transaxle case.

  1. C137417
    Using a pin punch (3 mm) and hammer, install a new slotted spring pin into the parking lock lever sub-assembly.

  1. C137429
    Turn the spacer and the lever shaft to align the smaller hole of the spacer with the staking position mark on the lever shaft.

  1. Using a pin punch, stake the spacer through the small hole.

  1. Check that the spacer does not turn.

  1. C136702
    Using a pin punch (3 mm) and hammer, install a new slotted spring pin into the manual valve lever sub-assembly.

  1. C137430
    Turn the spacer and the lever shaft to align the smaller hole of the spacer with the staking position mark on the lever shaft.

  1. Using a pin punch, stake the spacer through the small hole.

  1. Check that the spacer does not turn.

  1. C136680
    Using needle-nose pliers, install the manual valve shaft retainer spring to the transaxle case.


4. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

  1. C136683
    Align the slot with the notches on the parking lock lever sub-assembly and install the parking lock rod sub-assembly.


5. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

  1. C134953
    Install the manual detent spring sub-assembly and cover to the transaxle case with the bolt.

    Torque:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Make sure to install the manual detent spring first and then the cover.


6. INSTALL COUNTER DRIVE GEAR BEARING

NOTICE:
Perform this procedure only when the counter drive gear bearing or transaxle case is replaced.

  1. C138721E01
    Using SST and a press, install a new counter drive gear bearing and snap ring to the transaxle case.
    SST
    09950-60020   (09951-01030)
    09950-70010   (09951-07100)


7. INSTALL NO. 3 BRAKE PISTON

  1. C137432
    Coat the contact surface of the transaxle case with ATF.

  1. Coat the lip of the oil seal of the No. 3 brake piston with ATF.

  1. C137431
    Temporarily install the pawl stopper plate to the transaxle case with the 2 bolts.

  1. C136679
    Press the return spring installation surface to install the No. 3 brake piston into the transaxle case.

    NOTICE:
    1. Make sure that the lip of the No. 3 brake piston is not twisted and does not get caught in the transaxle case.
    2. After installing, make sure that the protrusions on the No. 3 brake piston and the grooves on the pawl stopper plate are aligned.

  1. Install the return spring to the transaxle case.

  1. C137422
    Remove the 2 bolts and pawl stopper plate from the transaxle case.

  1. C138725E01
    Place SST on the brake piston return spring and compress the brake piston return spring with a press.
    SST
    09387-00070  

    NOTICE:
    Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.

  1. Using a screwdriver, install the snap ring to the transaxle case as shown in the illustration.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the brake piston return spring as shown in the illustration.


8. INSTALL COUNTER DRIVE GEAR

  1. C137423E01
    Using SST and a press, install the bearing inner race (front side) to the counter drive gear.
    SST
    09387-00020  

  1. C137424E01
    Install the bearing inner race (rear side) and counter drive gear to the transaxle case.
    SST
    09223-15030  
    09527-17011  
    09950-60020   (09951-00810)
    09950-70010   (09951-07100)

    NOTICE:
    There should not be any clearance between the bearing inner race (front side) and counter drive gear.


9. INSTALL FRONT PLANETARY GEAR ASSEMBLY

  1. C137425E01
    Using SST and a press, press in the planetary gear assembly to the transaxle case.
    SST
    09223-15030  
    09527-17011  
    09951-01100  


10. INSTALL NO. 2 BRAKE PISTON

  1. C136673E01
    Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.

    NOTICE:
    Ensure that the 2 O-rings are not twisted.

  1. C138726
    Install the No. 2 brake piston to the transaxle case.

    NOTICE:
    Be careful not to damage the O-rings.


11. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
  1. Install the 1st and reverse brake return spring to the transaxle case.

  1. C137434E01
    Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring with a press.
    SST
    09387-00060  

    NOTICE:
    Stop the press when the 1st and reverse brake return spring is flush with the snap ring groove. This prevents the 1st and reverse brake return spring from being deformed.

  1. Using a screwdriver, install the snap ring to the transaxle case as shown in the illustration.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case as shown in the illustration.


12. INSTALL NO. 2 BRAKE DISC

  1. C136483E01
    Install the 5 brake discs, 5 brake plates, and brake flange to the transaxle case.

    NOTICE:
    Make sure that the discs, plates, and flange are installed in the correct order.

  1. C136481
    Using a screwdriver, install the snap ring to the transaxle case.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case as shown in the illustration.


13. INSPECT CLEARANCE OF NO. 2 BRAKE

  1. C137439
    Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    Standard clearance:
    0.884 to 1.196 mm (0.0348 to 0.0471 in.)

    HINT:
    Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.

    If the clearance is not as specified, select an appropriate No. 2 brake flange so that the clearance will be within the specified range.

    HINT:
    There are 5 flanges of different thicknesses.

    No. 2 brake flange thickness: mm (in.) 
    Thickness
    Thickness
    4.0 (0.157)
    4.3 (0.169)
    4.1 (0.161)
    4.4 (0.173)
    4.2 (0.165)
    -


14. INSTALL PLANETARY RING GEAR FLANGE

  1. C136480
    Install the planetary ring gear flange to the planetary ring gear.

  1. Using a screwdriver, install the snap ring to the planetary ring gear.

    NOTICE:
    Confirm that the snap ring is correctly located in the groove of the planetary ring gear.


15. INSTALL PLANETARY RING GEAR

  1. C136479
    Install the planetary ring gear to the one-way clutch assembly.

    NOTICE:
    Make sure that the one-way clutch assembly is positioned in the correct direction as shown in the illustration.


16. INSTALL ONE-WAY CLUTCH ASSEMBLY

  1. C136478E04
    Coat the thrust needle roller bearing with ATF, and install it onto the planetary gear assembly.
    Bearing diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    56.1 (2.209)
    80.9 (3.185)

    NOTICE:
    Install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.

  1. Install the one-way clutch assembly to the transaxle case.

    NOTICE:
    Make sure that there is no clearance between the retainer and the claw on the one-way clutch assembly. If there is any clearance, the spring of the retainer will be deformed.

  1. C136477
    Using a screwdriver, install the snap ring to the transaxle case.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case.


17. INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE

  1. C137443E01
    Using SST and a hammer, install the counter driven gear rear tapered roller bearing outer race to the transaxle case.
    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07100)

    NOTICE:
    Be sure to install the counter driven gear rear tapered roller bearing outer race so that there is no clearance between the bearing outer race and the transaxle case. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.


18. INSTALL PARKING LOCK PAWL

  1. C136475
    Install the parking lock pawl to the transaxle case with the parking lock pawl shaft.

  1. Install the parking lock pawl pin to the transaxle case.

  1. C137444
    Install the torsion spring to the parking lock pawl.

    NOTICE:
    Make sure that one end of the spring is fixed in the hole of the transaxle case and the other end is positioned on the parking lock pawl as shown in the illustration.


19. INSTALL PARKING LOCK SLEEVE

  1. C136474
    Install the parking lock sleeve to the transaxle case.


20. INSTALL PAWL STOPPER PLATE

  1. C136473
    Install the pawl stopper plate to the transaxle case with the 2 bolts.

    Torque:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }


21. INSTALL PAWL SHAFT CLAMP

  1. C136472
    Install the pawl shaft clamp to the transaxle case with the bolt.

    Torque:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }


22. INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING

  1. C138250E01
    Using SST and a press, install a new counter driven gear front tapered roller bearing to the counter driven gear sub-assembly.
    SST
    09950-60010   (09951-00530)

    NOTICE:
    Be sure to install the counter driven gear front tapered roller bearing so that there is no clearance between the bearing and the counter driven gear. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.


23. INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING

  1. C138251E01
    Using SST and a press, install a new counter driven gear rear tapered roller bearing to the counter driven gear sub-assembly.
    SST
    09950-60010   (09951-00420)

    NOTICE:
    Be sure to install the counter driven gear rear tapered roller bearing and the differential drive pinion so that there is no clearance between each of them and the counter driven gear.


24. INSTALL COUNTER DRIVEN GEAR

  1. C136469
    Install the counter driven gear sub-assembly to the transaxle case.


25. INSTALL COUNTER DRIVE GEAR NUT

  1. C136700E01
    Turn the manual shaft lever 2 notches counterclockwise to set it to the P position as shown in the illustration.

  1. C136468E01
    Using SST, install a new nut.
    SST
    09387-00130  

    Torque:
    120 N*m{ 1223 kgf*cm , 88 ft.*lbf }

  1. C136699E01
    Turn the manual shaft lever 2 notches clockwise to set it to the N position as shown in the illustration.

  1. C138252E01
    Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm.
    SST
    09387-00130  

    Turning torque:
    0.10 to 0.22 N*m (1.02 to 2.24 kgf*cm, 0.89 to 1.94 in.*lbf)

    When the measured value is not within the specified range, gradually tighten the nut until the turning toque falls within the specified range.

    Maximum torque:
    180 N*m (1835 kgf*cm, 132 ft.*lbf)

  1. C136698E01
    Using SST and a hammer, stake the planetary gear assembly.
    SST
    09930-00010  


26. INSTALL FRONT DIFFERENTIAL CASE

  1. C136467
    Install the differential case sub-assembly to the transaxle case.


27. INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

  1. C083562
    Hold the differential case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Place a dial indicator on the tip of the side gear tooth at a right angle.

  1. Hold the pinion gear in the differential case and measure the backlash of the side gear.

    Standard backlash:
    0 to 0.15 mm (0 to 0.0059 in.)

    Thrust washer thickness 
    Thickness
    Thickness
    1.50 mm (0.0591 in.)
    1.75 mm (0.0689 in.)
    1.55 mm (0.0610 in.)
    1.80 mm (0.0709 in.)
    1.60 mm (0.0630 in.)
    1.85 mm (0.07283 in.)
    1.65 mm (0.0650 in.)
    1.90 mm (0.07480 in.)
    1.70 mm (0.0669 in.)
    -
    If the backlash is greater than the standard range, select another side gear thrust washer.


28. INSTALL NO. 1 BRAKE PISTON

  1. C136466E01
    Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.

    NOTICE:
    Ensure that the 2 O-rings are not twisted.

  1. C138253
    Install the No. 1 brake piston to the oil pump assembly.

    NOTICE:
    Be careful not to damage the O-rings.


29. INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C136464
    Install the 3 2nd brake piston return springs to the oil pump assembly.

    NOTICE:
    Make sure that the 3 2nd brake piston return springs are installed straight through the protrusions on the oil pump assembly.


30. INSTALL NO. 1 BRAKE DISC

  1. C136463E01
    Install the 4 brake discs, 4 brake plates, and brake flange to the oil pump assembly.

    NOTICE:
    1. Make sure that the discs, plates, and flange are installed in the correct order.
    2. Be sure to install the flange in the correct direction.

  1. Place SST on the flange and compress the flange with a press.

    SST
    09387-00070  
    09495-65040  

    NOTICE:
    Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.

  1. C153479E01
    Using a screwdriver, install the snap ring to the oil pump assembly as shown in the illustration (#1).

    NOTICE:
    1. Confirm the snap ring is correctly located in the groove of the oil pump.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the brake piston return spring as shown in the illustration.

  1. C152849E01
    Install the brake snap ring stopper to the oil pump assembly.

    NOTICE:
    1. There are 2 types of brake snap ring stoppers depending on the vehicle.
    2. Be sure to install the brake snap ring stopper in the correct direction.

  1. C153480E01
    Using a screwdriver, install the snap ring to the oil pump assembly as shown in the illustration (#2).

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the oil pump.
    2. Make sure that the protrusions of the snap rings are positioned as shown in the illustration.

  1. C153481E01
    Check that the brake snap ring stopper can be turned by hand.

    NOTICE:
    If the brake snap ring stopper cannot be turned by hand, the brake snap ring stopper may have been installed upside down, or the snap ring may have not been completely fitted in the groove on the oil pump. Remove and reinstall the snap ring and the brake snap ring stopper.


31. INSPECT CLEARANCE OF NO. 1 BRAKE

  1. C138258
    Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    Standard clearance:
    0.807 to 0.974 mm (0.0318 to 0.0383 in.)

    HINT:
    Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.

    If the clearance is not as specified, select an appropriate No. 1 brake flange so that the clearance will be within the specified range.

    HINT:
    There are 6 flanges of different thicknesses.

    No. 1 brake flange thickness: mm (in.) 
    Thickness
    Thickness
    3.0 (0.118)
    3.3 (0.130)
    3.1 (0.122)
    3.4 (0.134)
    3.2 (0.126)
    3.5 (0.138)


32. INSTALL UNDERDRIVE PLANETARY SUN GEAR

  1. C136461
    Coat the thrust needle roller bearing with ATF, and install it to the oil pump assembly.
    Bearing diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    57.7 (2.272)
    75.2 (2.961)

    NOTICE:
    Install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.

  1. Install the underdrive planetary sun gear to the oil pump assembly.


33. INSTALL INPUT SHAFT SUB-ASSEMBLY

  1. C136460E01
    Coat the 3 input shaft oil seal rings with ATF and install them to the input shaft.

    NOTICE:
    Do not expand the gap of the oil seal ring too much.

  1. Coat the thrust needle roller bearing and thrust needle roller race with ATF, and install them on the oil pump assembly.

    Bearing diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    29.1 (1.146)
    48.6 (1.913)
    Race
    30.7 (1.209)
    48.3 (1.902)

    NOTICE:
    Be sure to install the thrust needle roller bearing in the correct direction.

  1. C136459
    Install the input shaft to the oil pump assembly.


34. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

  1. C136457
    Using a snap ring expander, install the snap ring to the underdrive planetary gear assembly.

  1. Using a snap ring expander, install the front planetary sun gear sub-assembly to the underdrive planetary gear assembly with the snap ring expanded.

    NOTICE:
    Confirm that the snap ring is correctly located in the groove of the planetary sun gear sub-assembly.


35. INSTALL UNDERDRIVE PLANETARY RING GEAR

  1. C136456
    Install the underdrive planetary ring gear to the underdrive planetary gear assembly.

  1. Using needle-nose pliers, install the snap ring to the underdrive planetary ring gear.

    NOTICE:
    Confirm that the snap ring is correctly located in the groove of the underdrive planetary ring gear.


36. INSTALL NO. 3 BRAKE HUB

  1. C136455E01
    Coat the thrust needle roller bearing with ATF and install it on the underdrive planetary gear assembly.
    Bearing diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    62.6 (2.464)
    82.9 (3.263)
    Race
    65.9 (2.594)
    80.3 (3.161)

    NOTICE:
    Install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.

  1. Coat the race with MP grease and install it to the No. 3 brake hub.

  1. C136454
    Install the No. 3 brake hub to the underdrive planetary gear assembly.


37. INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY

  1. C136458
    Install the underdrive planetary gear assembly to the oil pump assembly.


38. INSTALL NO. 3 BRAKE DISC

  1. C136452E01
    Install the 2 brake flanges, 3 brake discs, and 2 brake plates to the oil pump assembly.

    NOTICE:
    Make sure that the discs, plates, and flanges are installed in the correct order.

  1. C136451E02
    Using a screwdriver, install the snap ring to the oil pump assembly.

    NOTICE:
    1. Confirm the snap ring is correctly located in the groove of the oil pump.
    2. Make sure that the snap ring ends are positioned as shown in the illustration (A).


39. INSPECT CLEARANCE OF NO. 3 BRAKE

40. INSTALL FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY

  1. C138729E01
    Coat the O-ring with ATF and install it to the transaxle case.

  1. Coat the thrust needle roller bearing and thrust needle roller race with ATF and install them on the underdrive planetary gear assembly.

    Bearing and race diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    53.1 (2.091)
    79 (3.11)
    Race
    59.4 (2.339)
    77 (3.03)

    NOTICE:
    Install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.

  1. C136450
    Coat the O-ring with ATF and install it to the oil pump.

  1. Install the oil pump assembly to the transaxle case with the 7 bolts.

    Torque:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }


41. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

  1. C136449
    Install the differential gear lube apply tube to the transaxle housing.

    NOTICE:
    Insert the differential lube apply tube into the transaxle case until it makes contact with the stopper.

  1. Install the apply tube clamp to the differential gear lube apply tube with the bolt.

    Torque:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }

    NOTICE:
    There should be clearance between the differential lube apply tube and apply tube clamp.


42. INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE

  1. C138261E01
    Install the shim to the transaxle housing.

  1. Using SST, install a new counter driven gear front tapered roller bearing outer race to the transaxle housing.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07100)

    NOTICE:
    Be sure to install the counter driven gear front tapered roller bearing outer race so that there is no clearance between the shim and the transaxle housing.


43. INSTALL TRANSAXLE HOUSING
  1. Remove packing material from the contact surfaces between the transaxle housing and case.

    NOTICE:
    Make sure that there is no ATF on the contact surfaces.

  1. C138263E01
    Apply FIPG to the transaxle case.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Apply FIPG in a continuous line (width 1.2 mm (0.047 in.)) along the sealing surface.

  1. C136447E01
    Install the transaxle housing to the transaxle case with the 20 bolts.

    Torque:
    Bolt A:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }
    Bolt B:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }


44. ADJUST COUNTER DRIVEN GEAR PRELOAD

  1. C138262E01
    Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.
    SST
    09564-33010  

    Turning torque:
    Differential side bearing preload 3.29 to 6.07 N*m (33.53 to 61.86 kgf*cm, 2.42 to 4.46 ft.*lbf)

    If the turning torque is not within the specified range, refer to the table below to select a shim of the counter driven gear front tapered roller bearing outer race so that the turning torque is within the specified range.
    Shim thickness: mm (in.) 
    Thickness
    Thickness
    Thickness
    Thickness
    2.000 (0.0787)
    2.275 (0.0896)
    2.525 (0.0994)
    2.775 (0.1093)
    2.025 (0.0797)
    2.300 (0.0906)
    2.550 (0.1004)
    2.800 (0.1102)
    2.050 (0.0807)
    2.325 (0.0915)
    2.575 (0.1014)
    2.825 (0.1112)
    2.075 (0.0817)
    2.350 (0.0925)
    2.600 (0.1024)
    2.850 (0.1122)
    2.100 (0.0827)
    2.375 (0.0935)
    2.625 (0.1034)
    2.875 (0.1132)
    2.125 (0.0837)
    2.400 (0.0945)
    2.650 (0.1043)
    2.900 (0.1142)
    2.150 (0.0847)
    2.425 (0.0955)
    2.675 (0.1053)
    2.925 (0.1152)
    2.175 (0.0856)
    2.450 (0.0965)
    2.700 (0.1063)
    2.950 (0.1161)
    2.200 (0.0866)
    2.475 (0.0974)
    2.725 (0.1073)
    2.975 (0.1171)
    2.225 (0.0876)
    2.500 (0.0984)
    2.750 (0.1083)
    3.000 (0.1181)
    2.250 (0.0886)
    -
    -
    -


45. INSTALL NO. 1 CLUTCH DISC

  1. C136446E01
    Install the 2 clutch flanges, 4 clutch discs, and 4 clutch plates to the direct multiple disc clutch assembly.

    NOTICE:
    Make sure that the flanges, discs, and plates are installed in the correct order.

  1. C136445
    Using a screwdriver, install the 2 snap rings to the direct multiple disc clutch assembly.

    NOTICE:
    Confirm that the snap rings are correctly located in the groove of the direct multiple disc clutch assembly.


46. INSPECT CLEARANCE OF NO. 1 CLUTCH DISC

  1. C138728
    Install the direct multiple disc clutch assembly onto the transaxle rear cover.

  1. Using a dial indicator, measure the No. 1 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    HINT:
    Measure the clearance at 3 points where the flange diameter is approximately 152 mm (5.98 in.) and calculate the average.

    Pack clearance:
    0.806 to 0.974 mm (0.0317 to 0.0383 in.)

    If the pack clearance is not as specified, inspect the discs, plates and flange.

    HINT:
    There are 6 flanges of different thicknesses.

    No. 1 clutch flange thickness: mm (in.) 
    Thickness
    Thickness
    3.0 (0.118)
    3.3 (0.130)
    3.1 (0.122)
    3.4 (0.134)
    3.2 (0.126)
    3.5 (0.138)


47. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

  1. C136438E01
    Coat the thrust needle roller bearing and thrust needle roller race with ATF, and install them to the direct multiple disc clutch assembly.
    Bearing and race diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    28 (1.10)
    47.1 (1.854)
    Race
    26.1 (1.028)
    44 (1.73)

    NOTICE:
    Install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.

  1. C136437
    Install the rear planetary sun gear to the direct multiple disc clutch assembly.

  1. C136436
    Using a snap ring expander, install the snap ring to the direct multiple disc clutch assembly.


48. INSTALL NO. 2 CLUTCH DISC

  1. C136435E01
    Install the clutch flange, 3 clutch discs, and 3 clutch plates to the direct multiple disc clutch assembly.

    NOTICE:
    Make sure that the flange, discs, and plates are installed in the correct order.


49. INSTALL DIRECT MULTIPLE DISC CLUTCH SNAP RING

  1. C136428E01
    Coat a new O-ring with ATF and install it to the direct multiple disc clutch assembly.

  1. Coat a new intermediate shaft oil seal with ATF and install it to the intermediate shaft.

  1. C136434
    Install the No. 2 direct clutch piston to the direct multiple disc clutch assembly.

    NOTICE:
    Be sure to engage the claws on the direct multiple disc clutch assembly in the grooves on the No. 2 direct clutch piston.

  1. C136433E01
    Using a screwdriver, install the snap ring to the direct multiple disc clutch assembly.

    NOTICE:
    1. Position the opening of the snap ring as shown in the illustration.
    2. Confirm the snap ring is correctly located in the direct multiple disc clutch assembly.


50. INSPECT CLEARANCE OF NO. 2 CLUTCH DISC

  1. C138727
    Install the direct multiple disc clutch assembly onto the transaxle rear cover.

  1. Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    HINT:
    Measure the clearance at 3 points where the diameter of the No. 2 direct multiple clutch piston is approximately 152 mm (5.98 in.) and calculate the average.

    Pack clearance:
    0.544 to 0.744 mm (0.0214 to 0.0293 in.)

    If the pack clearance is not as specified, inspect the discs, plates and flange.

    HINT:
    There are 6 flanges of different thicknesses.

    No. 2 clutch flange thickness: mm (in.) 
    Thickness
    Thickness
    3.0 (0.118)
    3.3 (0.130)
    3.1 (0.122)
    3.4 (0.134)
    3.2 (0.126)
    3.5 (0.138)


51. INSTALL REAR MULTIPLE DISC CLUTCH ASSEMBLY

  1. C136442
    Coat the thrust needle roller bearing with ATF and install it on the transaxle case.
    Bearing diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    61.2 (2.409)
    79 (3.11)

  1. Install the direct multiple disc clutch assembly to the transaxle case.

  1. Clean the contact surfaces of the transaxle case and transaxle rear cover.

  1. C138269E01
    As shown in the illustration, place a straight edge on the multiple direct clutch drum and measure the distance between the transaxle case and the straight edge using vernier calipers (Dimension A).

  1. C138268E01
    Using vernier calipers and a straight edge, measure the distance shown in the illustration. (Dimension B)

  1. Calculate the end play value using the following formula:
    End play = Dimension B - Dimension A

    End play:
    0.007 to 1.113 mm (0.0003 to 0.0438 in.)


52. INSTALL TRANSAXLE REAR COVER SUB-ASSEMBLY

  1. C138270E01
    Using SST and a hammer, install the needle roller bearing into the transaxle rear cover.
    SST
    09950-60010   (09951-00220)
    09950-70010   (09951-07100)

    Installation depth:
    21.5 to 21.9 mm (0.8464 to 08622 in.)

  1. Apply adhesive to the 2 "TORX" screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. C136443
    Using a "TORX" wrench (T30), install the transaxle rear cover plate to the transaxle rear cover with the 2 "TORX" screws.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. C136440E01
    Coat the thrust needle roller bearing and thrust needle roller race with ATF and install them on the transaxle case.
    Bearing diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    48.9 (1.925)
    72.0 (2.835)
    Race
    52.2 (2.055)
    70.4 (2.772)

  1. Coat 2 new oil seal rings with ATF and install them to the transaxle rear cover.

  1. C136432
    Coat the 3 O-rings with ATF and install them to the transaxle case.

    NOTICE:
    Ensure that the 3 O-rings are not twisted.

  1. C138271
    Remove packing material from the contact surfaces between the transaxle rear cover and transaxle case.

    NOTICE:
    Make sure that there is no ATF on the contact surfaces.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent.

  1. C136431E01
    Install the transaxle rear cover to the transaxle case with the 14 bolts.

    Torque:
    Bolt A:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }
    Bolt B:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }

  1. C136430
    Install a new gasket to the refill plug.

  1. Install the refill plug to the transaxle rear cover.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. C134960
    Coat 2 new O-rings with ATF and install them to the 2 No. 1 automatic transaxle case plugs.

  1. Install the 2 No. 1 automatic transaxle case plugs to the transaxle rear cover.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


53. INSPECT INPUT SHAFT END PLAY

  1. C136696
    Using a dial indicator, measure the input shaft end play.

    End play:
    0.012 to 1.250 mm (0.0005 to 0.0492 in.)


54. INSTALL TRANSAXLE CASE GASKET

  1. C136429
    Coat the 2 gaskets with ATF and install them to the transaxle case.


55. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

  1. C161959E01
    Install the valve body assembly to the transaxle case with the 11 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    -
    -
    Bolt length
    Bolt length
    Bolt A
    25 mm (0.98 in.)
    Bolt B
    30 mm (1.18 in.)
    Bolt C
    35 mm (1.38 in.)
    Bolt D
    45 mm (1.77 in.)
    Bolt E
    55 mm (2.17 in.)

    NOTICE:
    1. When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case to interfere with each other.
    2. Be sure to insert the pin of the manual valve lever into the groove on the end of the manual valve.
    3. First, temporarily tighten the bolts marked by (*1) in the illustration because they are positioning bolts.


56. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

  1. C136688
    Coat a new O-ring with ATF and install it to the oil strainer assembly.

    NOTICE:
    Ensure that the O-ring is not twisted or pinched.

  1. C136687
    Install the oil strainer assembly to the valve body assembly with the 2 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


57. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

  1. C134963
    Install the 2 magnets in the automatic transaxle oil pan sub-assembly.

  1. Apply adhesive to the 18 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. C134962
    Install the automatic transaxle oil pan sub-assembly and a new gasket to the transaxle case with the 18 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    1. In order to ensure proper sealing of the transmission pan bolts, apply adhesive to the bolts and install them within 10 minutes of adhesive application.
    2. Completely remove any oil or grease from the contact surfaces of the transaxle case and oil pan sub-assembly with the gasket before installation.

  1. C141531
    Install the No. 1 oil filler tube to the automatic transaxle assembly.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }

  1. C134961
    Install the overflow plug and a new gasket to the oil pun sub-assembly.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


58. INSTALL NO. 1 TRANSAXLE CASE PLUG
  1. Install the 3 gaskets to the 3 hexagon bolts.

  1. Apply adhesive to the 3 hexagon bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    In order to ensure proper sealing of the hexagon bolts, apply adhesive to the bolts and install them within 10 minutes of adhesive application.

  1. C134959
    Install the 3 hexagon bolts to the transaxle housing with the gaskets.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. C134958
    Coat 3 new O-rings with ATF and install them to the 3 No. 1 transaxle case plugs.

  1. Install the 3 No. 1 transaxle case plugs to the transaxle case.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


59. INSTALL OIL COOLER TUBE UNION (INLET OIL COOLER UNION)

  1. C134957
    Coat a new O-ring with ATF and install it to the oil cooler tube union (inlet oil cooler union).

  1. Install the oil cooler tube union (inlet oil cooler union) to the transaxle case.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }


60. INSTALL OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)

  1. C134956
    Coat a new O-ring with ATF and install it to the oil cooler tube union (outlet oil cooler union).

  1. Install the oil cooler tube union (outlet oil cooler union) to the transaxle case as shown in the illustration.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }


61. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C135733E01
    Align the protrusions of the park/neutral position switch.

  1. C136686
    Install the park/neutral position switch to the control shaft with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    1. Before installing the park/neutral position switch, remove any dirt or rust on the installation portion of the control shaft. Be sure to install the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch cannot be reinstalled correctly.
    2. After installing the park/neutral position switch, confirm that the 2 protrusions on the switch are aligned.

  1. C136685
    Install the control shaft lever to the control shaft with the washer and nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


62. INSTALL BREATHER PLUG HOSE

  1. C134952E01
    Install a new O-ring to the breather plug.

  1. Install the breather plug to the breather plug hose.

  1. Install the breather plug cap to the breather plug hose.

  1. C134951
    Install the breather plug hose to the transaxle case.

← INSPECTION (from Oct 2006)COMPONENTS (from Oct 2006) →