REMOVAL
Removal / installation · Vehicles built from Oct 2006
| 1. REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH (w/o Rear Lower Spoiler) |
Remove the 3 screws and rear quarter panel mudguard sub-assembly LH.

| 2. REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY RH (w/o Rear Lower Spoiler) |
- HINT:
- Use the same procedure for the RH side and LH side.
| 3. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler) |
Remove the 4 screws, 2 clips, 3 nuts and rear floor board.

| 4. REMOVE REAR BUMPER ASSEMBLY (w/o Clearance Sonar System) |
without Rear Lower Spoiler:
Put protective tape around the rear bumper assembly.

Using a screwdriver, open the 2 rear bumper plates.

- HINT:
- Tape the screwdriver tip before use.
Remove the 6 screws and 2 clips.

Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

- HINT:
- Use the same procedure for the RH side and LH side.
Remove the rear bumper assembly.
with Rear Lower Spoiler:
Put protective tape around the rear bumper assembly.

Using a screwdriver, open the 2 rear bumper plates.

- HINT:
- Tape the screwdriver tip before use.
Remove the 6 screws.

Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

- HINT:
- Use the same procedure for the RH side and LH side.
Remove the rear bumper assembly.
| 5. REMOVE LUGGAGE COMPARTMENT FLOOR MAT (w/ Clearance Sonar System) |
| 6. REMOVE SPARE WHEEL COVER CLAMP (w/ Clearance Sonar System) |
| 7. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Clearance Sonar System) |
| 8. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (w/ Clearance Sonar System) |
Remove the 2 screws and the 2 No. 1 luggage compartment trim hooks.

| 9. REMOVE REAR FLOOR FINISH PLATE (w/ Clearance Sonar System) |
Disengage the 7 clips and remove the rear floor finish plate.

| 10. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER RH (w/ Clearance Sonar System) |
Remove the 2 clips and the luggage compartment inner trim cover RH.

| 11. REMOVE REAR BUMPER ASSEMBLY (w/ Clearance Sonar System) |
without Rear Lower Spoiler:
Disconnect the connector.

Disengage the grommet.
Put protective tape around the rear bumper assembly.

Using a screwdriver, open the 2 rear bumper plates.

- HINT:
- Tape the screwdriver tip before use.
Remove the 6 screws and 2 clips.

Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

- HINT:
- Use the same procedure for the RH side and LH side.
Disengage each No. 2 luggage room wire clamp from the rear bumper reinforcement sub-assembly.
Remove the rear bumper assembly.
with Rear Lower Spoiler:
Disconnect the connector.

Disengage the grommet.
Put protective tape around the rear bumper assembly.

Using a screwdriver, open the 2 rear bumper plates.

- HINT:
- Tape the screwdriver tip before use.
Remove the 6 screws.

Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

- HINT:
- Use the same procedure for the RH side and LH side.
Disengage each No. 2 luggage room wire clamp from the rear bumper reinforcement sub-assembly.
Remove the rear bumper assembly.
