2006-2011 Camry Aurion · Service Manual BRAKE

REASSEMBLY

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009


1. INSTALL PARKING BRAKE SHOE LEVER

2. INSTALL DUST COVER

  1. C141965
    Install the dust cover to the parking brake shoe lever as shown in the illustration.

  1. C142623
    Using an air riveter or a hand riveter with a nose piece, install the boot retainer on the back plate with 2 new rivets.

    HINT:
    If the rivet cannot be cut, pull it once and cut it.

    NOTICE:

    1. B125583E01
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    2. B125584E01
      Confirm that the rivets are seated properly against the boot retainer. Do not tilt the riveter when installing the rivet to the boot retainer. Do not leave any space between the rivet head and the boot retainer.

    3. B125585E01
      Do not leave any space between the boot retainer and the back plate. Firmly hold together the 2 items while installing the rivet.


3. INSTALL DUST PLATE
  1. Install the dust plate to the parking brake plate sub-assembly.


4. INSTALL PARKING BRAKE SHOE HOLD PLATE

  1. C141963
    Install the parking brake shoe hold plate with a new parking brake shoe hold bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


5. INSTALL ADJUSTMENT PAWL

  1. C143767
    Install the adjustment pawl.


6. INSTALL NUT AND SCREW ADJUSTING ASSEMBLY

  1. C141966E01
    Apply high temperature grease to the inside of the back plate bore as shown in the illustration.

  1. Install the nut and screw adjusting assembly, parking brake tappet and parking brake push rod.


7. INSTALL PARKING BRAKE PLATE SUB-ASSEMBLY

8. INSTALL REAR AXLE HUB & BEARING ASSEMBLY

  1. C083035E02
    Install the hub and bearing assembly with the 4 bolts.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }

  1. Connect the skid control sensor connector.

    NOTICE:
    Do not twist the sensor wire when connecting it.


9. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

  1. C141953
    Turn and connect the No. 3 parking brake cable assembly.

  1. Using a brass bar and a hammer, install the clip to the No. 3 parking brake cable assembly.


10. INSTALL PARKING BRAKE SHOE ASSEMBLY

  1. C141951
    Install the parking brake shoe assembly as shown in the illustration.

    NOTICE:
    There should be no oil or grease on the friction surface of the lining and disc.


11. INSPECT REAR AXLE HUB BEARING LOOSENESS

  1. C224308E01
    Using a dial indicator, check for looseness near the center of the axle hub.

    Maximum:
    0.05 mm (0.0020 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    If looseness exceeds the maximum, replace the axle hub assembly.


12. INSPECT REAR AXLE HUB RUNOUT

  1. C224310E01
    Using a dial indicator, check for runout on the surface of the axle hub outside the hub bolt.

    Maximum:
    0.07 mm (0.0027 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    If runout exceeds the maximum, replace the axle hub assembly.


13. INSTALL REAR DISC

  1. C138224E02
    Align the matchmarks and install the rear disc.


14. ADJUST PARKING BRAKE SHOE CLEARANCE
  1. Remove the rear brake caliper.

    HINT:
    1. Do not disconnect the flexible hose.
    2. Do not remove the brake pads.
    3. Do not allow the caliper to hang on the flexible hose. Always support the caliper.

  1. Remove the disc rotor.

    HINT:
    1. If the disc rotor is difficult to remove, rotate the disc whilst pulling on the rotor.
    2. If the disc jams, return the disc to its original position, turn the shoe adjuster in a clockwise direction to contact the brake and attempt to remove the disc again.

  1. C171322
    Measure the brake shoe diameter as shown in the illustration.

    Standard diameter:
    189.55 to 189.75 mm (7.463 to 7.470 in.)

  1. C171323E01
    If the shoe diameter is out of specification, adjust it by turning the nut as shown in the illustration.

  1. C171324E01
    The gap between the adjusting nut and screw must not exceed 5 mm (0.197 in.) as shown in the illustration. If the gap is set to this specification and the shoe diameter is less than specified, replace the parking brake shoe. If the lining thickness is less than 1.5 mm (0.059 in.) or exhibits uneven wear, replace the parking brake shoe.

  1. Check for drag. Spin the rotor and ensure there is no drag from the parking brake shoe.

    HINT:
    If there is drag, apply and release the parking brake lever or parking brake pedal and retest. If drag is still present, remove the disc, remeasure and readjust the shoe diameter and centralize the shoe. Reassemble the disc and recheck for drag.


15. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

16. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

  1. C138223
    Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }


17. INSTALL REAR WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


18. INSPECT PARKING BRAKE LEVER TRAVEL (for Lever Type Parking Brake)
  1. Pull the parking brake lever firmly.

  1. Release the parking brake lock, and return the parking brake lever to its off position.

  1. C147260
    Slowly pull the parking brake lever all the way up, and count the number of clicks.

    Parking brake lever travel:
    7 to 9 notches at 200 N (20 kgf, 45 lbf)


19. INSPECT PARKING BRAKE PEDAL TRAVEL (for Pedal Type Parking Brake)
  1. Fully depress the parking brake pedal and release it to engage the parking brake.

  1. Depress the pedal to the floor again, and release it to disengage the parking brake.

  1. C107204
    Slowly depress the parking brake pedal to the floor, and count the number of clicks.

    Parking brake pedal travel:
    7 to 10 notches at 300 N (31 kgf, 67 lbf)


20. ADJUST PARKING BRAKE LEVER TRAVEL (for Lever Type Parking Brake)
  1. Pull up the parking brake lever. Hold the No. 1 wire adjusting nut using a wrench and loosen the lock nut.

  1. Release the parking brake lever.

  1. C147261E01
    Turn the No. 1 wire adjusting nut until the parking brake lever travel meets the above specification.

  1. Hold the No. 1 wire adjusting nut using a wrench or an equivalent tool and tighten the lock nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Count the number of clicks after pulling and releasing the parking brake lever 3 or 4 times.

  1. Check whether the parking brake drags.

  1. When operating the parking brake lever, check that the parking brake indicator light comes on.


21. ADJUST PARKING BRAKE PEDAL TRAVEL (for Pedal Type Parking Brake)
  1. Depress the parking brake pedal. Hold the No. 1 wire adjusting nut using a wrench and loosen the lock nut.

  1. Release the parking brake pedal.

  1. C133443E01
    Turn the No. 1 wire adjusting nut until the parking brake pedal travel meets the above specification.

  1. Hold the No. 1 wire adjusting nut using a wrench or an equivalent tool and tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Count the number of clicks after depressing and releasing the parking brake pedal 3 or 4 times.

  1. Check whether the parking brake drags.

  1. When operating the parking brake pedal, check that the parking brake indicator light comes on.


22. INSPECT SENSOR SIGNAL
  1. ABS: Click here

  1. VSC: Click here

← REASSEMBLY (Jun 2006 – Sep 2006)PRECAUTION (Jun 2006 – Sep 2006) →