2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

B1273 Sliding Roof ECU Communication Stop

Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This DTC is output when LIN communication between the sliding roof ECU (Sliding roof drive gear) and main body ECU (Instrument panel junction block assembly) stops for more than 10 seconds.
DTC No.
DTC Detection Condition
Trouble Area
B1273
No communication between sliding roof ECU (Sliding roof drive gear) and main body ECU (Instrument panel junction block assembly) for more than 10 seconds
  1. Sliding roof ECU (Sliding roof drive gear)
  2. Main body ECU (Instrument panel junction block assembly)
  3. Wire harness or connector

WIRING DIAGRAM

B176995E11

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the engine switch off to troubleshoot:
Connect the intelligent tester to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.


1. CLEAR DTC
  1. Delete the DTC (Click here).


NEXT


2. CHECK DTC OUTPUT
  1. Recheck for DTC (Click here).

    Result:
    Result
    Proceed to
    B1273 is output
    A
    B1273 is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SLIDING ROOF ECU)

  1. Disconnect the E8 and Q12 connectors.B178901E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-10 (LIN2) - Q12-4 (MPX1)
    Always
    Below 1 Ω
    E8-10 (LIN2) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-10 (LIN2) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY AND GROUND)

  1. B164448E04
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q12-2 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Q12-1 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR)
  1. Replace the sliding roof ECU (Sliding roof drive gear) with a normally-functioning or a new one (Click here).

  1. Delete the DTC (Click here).


NEXT


6. CHECK DTC OUTPUT
  1. Recheck for DTC (Click here).

    Result:
    Result
    Proceed to
    B1273 is not output
    A
    B1273 is output
    B



B
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
A

END (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR) IS DEFECTIVE)


← DIAGNOSTIC TROUBLE CODE CHART (from Jun 2009)B1273 Sliding Roof ECU Communication Stop (Oct 2006 – May 2009) →