B2321 Driver Side Door ECU Communication Stop
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
This DTC is output when LIN communication between the power window regulator motor (Driver side) and main body ECU (Instrument panel junction block assembly) stops for more than 10 seconds.| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2321 |
No communication between power window regulator motor (Driver side) and main body ECU (Instrument panel junction block assembly) for more than 10 seconds |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the ignition switch off to troubleshoot:
- Connect the intelligent tester to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.
| 1. CLEAR DTC |
Delete the DTC (Click here).
| NEXT | |
| 2. CHECK DTC OUTPUT |
Recheck for DTC (Click here).
- Result:
Result
Proceed to
B2321 is not output
A
B2321 is output
B
|
|
||||
| A | |
| 3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MOTOR) |
Disconnect the E8 and I5*1 or H10*2 connectors.
- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
for LHD Tester Connection
Condition
Specified Condition
E8-10 (LIN2) - I5-9 (LIN)
Always
Below 1 Ω
E8-10 (LIN2) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
E8-10 (LIN2) - H10-9 (LIN)
Always
Below 1 Ω
E8-10 (LIN2) - Body ground
Always
10 kΩ or higher
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E8-10 (LIN2) - Body ground
Always
Below 1 V
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND) |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
for LHD Tester Connection
Condition
Specified Condition
I5-1 (E) - Body ground
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
H10-1 (E) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
for LHD Tester Connection
Condition
Specified Condition
I5-2 (B) - Body ground
Always
11 to 14 V
for RHD Tester Connection
Condition
Specified Condition
H10-2 (B) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 5. REPLACE POWER WINDOW REGULATOR MOTOR (DRIVER SIDE) |
Replace the power window regulator motor (Driver side) with a normally-functioning or a new one (Click here).
Delete the DTC (Click here).
| NEXT | |
| 6. CHECK DTC OUTPUT |
Recheck for DTC (Click here).
- Result:
Result
Proceed to
B2321 is not output
A
B2321 is output
B
|
|
||||
| A | ||
| ||
