2006-2011 Camry Aurion · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL NO. 2 WINDSHIELD GLASS STOPPER
  1. Using a brush or sponge, coat the application area of the No. 2 stoppers with Primer G.

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer coating to dry for 3 minutes or more.
    3. Do not keep any of the opened Primer G for later use.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

  1. Install 2 new No. 2 stoppers onto the windshield glass, as shown in the illustration.

    HINT:
    Only 2-piece type No. 2 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.

    Standard dimension:
    Area
    Dimension
    A
    13.2 mm (0.519 in.)


    B136136E02


2. INSTALL WINDSHIELD GLASS RETAINER
  1. Using a brush or sponge, coat the application area of the retainers with Primer G.

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer coating to dry for 3 minutes or more.
    3. Do not keep any of the opened Primer G for later use.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

  1. Install 2 new retainers onto the windshield glass, as shown in the illustration.

    B147773E01


3. INSTALL NO. 1 WINDSHIELD GLASS STOPPER

  1. B144518E01
    Install 2 new No. 1 stoppers to the vehicle body, as shown in the illustration.

    HINT:
    Only 2-piece type No. 1 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.


4. INSTALL WINDSHIELD MOULDING
  1. Using a brush or sponge, coat the application area of the moulding with Primer G.

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer coating to dry for 3 minutes or more.
    3. Do not keep any of the opened Primer G for later use.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

  1. Install a new moulding onto the windshield glass, as shown in the illustration.

    B136139E02


5. INSTALL WINDOW GLASS ADHESIVE DAM
  1. Using a brush or sponge, coat the application area of the adhesive dam with Primer G.

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer coating to dry for 3 minutes or more.
    3. Do not keep any of the opened Primer G for later use.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

  1. Install a new adhesive dam onto the windshield glass, as shown in the illustration.

    NOTICE:
    Install the new adhesive dam along the ceramic notches.

    Standard dimension:
    Area
    Dimension
    A
    6.5 mm (0.255 in.)


    B136138E02


6. INSTALL WINDSHIELD GLASS ASSEMBLY

  1. B156164E01
    Position the windshield glass assembly.

    1. Using a suction cup, place the windshield glass assembly in the correct position.

    2. Check that the whole contact surface of the windshield glass rim is perfectly even.

    3. Align the matchmarks on the windshield glass and vehicle body.

      NOTICE:
      Check that the windshield glass stoppers are attached to the vehicle body correctly.

    4. Remove the windshield glass assembly.

  1. B136140E01
    Using a brush, coat the installation surface on the vehicle body with Primer M.

    NOTICE:
    1. Do not coat the adhesive with Primer M.
    2. Do not apply too much primer.
    3. Allow the primer coating to dry for 3 minutes or more.
    4. Do not keep any of the opened Primer M for later use.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

  1. Using a brush or sponge, coat the application area of adhesive with Primer G.

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer coating to dry for 3 minutes or more.
    3. Do not keep any of the opened Primer G for later use.

    HINT:
    1. Apply Primer G onto the ceramic notches.
    2. If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

    Standard dimension:
    Area
    Dimension
    a
    8.7 mm (0.342 in.)
    b
    7.0 mm (0.275 in.)
    c
    6.5 mm (0.255 in.)


    B136141E02

  1. Apply adhesive (Adhesive: TOYOTA genuine windshield glass adhesive or equivalent).

    1. Cut off the tip of the cartridge nozzle, as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time described in the table below.

      Usage time frame:
      Temperature
      Tack-free Time
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour and 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with cartridge.

    3. Apply adhesive to the windshield glass, as shown in the illustration.

      HINT:
      Apply adhesive onto the ceramic notches.

      Standard dimension:
      Area
      Dimension
      a
      8.7 mm (0.342 in.)
      b
      6.5 mm (0.255 in.)
      c
      12.0 mm (0.472 in.)
      d
      8.0 mm (0.315 in.)


      B136142E02

  1. B156165E01
    Install the windshield glass assembly.

    1. Using a suction cup, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

      NOTICE:
      1. Check that the windshield glass stoppers are attached to the vehicle body correctly.
      2. Check the clearance between the vehicle body and windshield glass.

    2. Lightly press the front surface of the windshield glass to ensure a close fit.

      HINT:
      Press the glass with a force of 98 N (10 kgf, 22 lb) or more.

    3. B149738E01
      If necessary, use a scraper to correct the level or position of adhesive that has been applied.

      HINT:
      Apply adhesive onto the windshield glass rim.

    4. Hold the windshield glass using protective tape until applied adhesive becomes hard.

      NOTICE:
      Do not drive the vehicle for the time described in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour and 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours


7. INSPECT FOR LEAK AND REPAIR
  1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

  1. If water leaks into the cabin, allow the water to dry and add adhesive.

  1. Remove the protective tape.


8. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
Return the front section of the roof headlining assembly to the original position (Click here).

9. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
Return the front section of the roof headlining assembly to the original position (Click here).

10. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (for Driver Side)

  1. with Assist Grip:

    1. B132101
      Assemble the front assist grip sub-assembly as shown in the illustration.

    2. B132102
      Install the front assist grip sub-assembly.


11. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (for Front Passenger Side)

  1. B147412
    Assemble the front assist grip sub-assembly as shown in the illustration.

  1. B147408
    Install the front assist grip sub-assembly.


12. INSTALL VISOR HOLDER
  1. Engage the 2 claws.

  1. Push in the visor holder as shown in the illustration.

    B149236

    HINT:
    Use the same procedure for the RH side and the LH side.


13. INSTALL VISOR ASSEMBLY LH

  1. B139565
    Engage the 2 clips and install the visor assembly LH.

  1. B139566
    Engage the 4 claws and install the visor bracket cover.


14. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


15. INSTALL ROOF CONSOLE BOX ASSEMBLY

  1. B132065
    Connect the connectors.

  1. Engage the 2 claws and 2 clips, and then install the roof console box assembly.


16. INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

  1. B149232E01
    Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish LH.


17. INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

  1. B154714E01
    Remove the protective cover.

  1. B149232E01
    Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish LH.


18. INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

  1. B149231E01
    Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish RH.


19. INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

  1. B154715E01
    Remove the protective cover.

  1. B149231E01
    Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish RH.


20. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  1. B132081E01
    Install the front door opening trim weatherstrip LH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


21. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B132083E01
    Install the front door opening trim weatherstrip RH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


22. INSTALL RAIN SENSOR TAPE (w/ Rain Sensor)

NOTICE:
The rain sensor tape can be reused, however, replace it with a new one if it is dirty or damaged.

HINT:
This step should be performed only when the rain sensor tape needs to be replaced.

  1. E128846E01
    Remove the releasing sheet (yellow side) from new rain sensor tape and attach the tape to the position indicated in the illustration (the sensor part of the rain sensor) while pushing out air bubbles with your fingers.

  1. Remove the releasing sheet (white side) from the rain sensor tape.

    NOTICE:
    1. Check that the old rain sensor tape is not left on the windshield glass. If the tape is still on the windshield glass, remove it before installing the rain sensor.
    2. Do not touch the sensor tape surface or the glass surface directly with your fingers.
    3. Clean up dirt on the glass with a cloth, etc.

    Area
    Measurement
    A
    7.3 mm (0.287 in.)
    B
    13.5 mm (0.531 in.)


23. INSTALL RAIN SENSOR (w/ Rain Sensor)

  1. E128845
    Connect the connector.

  1. E128847E01
    Gradually attach the rain sensor to the glass surface to prevent air bubbles from forming between them.

  1. Hold the rain sensor and push in the stopper.

    NOTICE:
    1. Do not touch the sensor tape surface or the glass surface directly with your fingers.
    2. Clean up dirt on the glass with a cloth, etc.
    3. After installing the rain sensor, there should be no air bubbles between the windshield glass and the rain sensor tape.


24. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

  1. E128843
    Install the rain sensor cover.


25. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

  1. B136887
    Slide the inner rear view mirror assembly in the direction indicated by the arrow shown in the illustration to install it.

  1. B136836
    Engage the 2 claws and install the cover.


26. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

  1. B155591
    Slide the inner rear view mirror assembly in the direction indicated by the arrow shown in the illustration to install it.

  1. B155590
    Using a "TORX" socket wrench (T20), install the inner rear view mirror with the screw.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. Connect the connector.


27. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

  1. B155589
    Engage the 2 claws and install the inner rear view mirror stay holder cover as shown in the illustration.


28. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

  1. E135588
    Engage the 4 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.


29. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

  1. E140957
    Engage the 3 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.


30. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

  1. E128810
    Engage the claw and install the front fender to cowl side seal RH.


31. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

  1. E128809
    Engage the claw and install the front fender to cowl side seal LH.


32. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

33. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. E112237E01
    Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E128820E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    37 to 52 mm (1.46 to 2.05 in.)


34. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. E112237E01
    Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E128821E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    23 to 38 mm (0.90 to 1.49 in.)

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


35. INSPECT SRS WARNING LIGHT
(Click here)
← INSTALLATION (Oct 2006 – May 2009)COMPONENTS (Jun 2006 – Sep 2006) →