2006-2011 Camry Aurion · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE REAR SEAT CUSHION ASSEMBLY
for Fixed Seat Type (Click here)
for Fold Down Seat Type (Click here)

3. REMOVE REAR SEAT HEADREST ASSEMBLY

4. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)

5. REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

  1. B136576
    Remove the 3 rear seat belts from the 3 rear seat shoulder belt guides.

  1. B136577
    Remove the 4 bolts and rear seatback assembly.


6. REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

  1. B136539
    Remove the 2 bolts and separate type rear seatback assembly LH.


7. REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

  1. B134700
    Remove the 2 bolts and separate type rear seatback assembly RH.


8. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

  1. B136561
    Remove the bolt and rear side seatback assembly LH.


9. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

HINT:
Use the same procedures for the RH side and LH side.


10. REMOVE REAR DOOR SCUFF PLATE LH

  1. B132068
    Disengage the 5 claws and 2 clips, and remove the rear door scuff plate LH.


11. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

12. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


13. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

14. REMOVE ROOF SIDE INNER GARNISH LH

  1. B132063
    Disengage the 5 clips and 2 claws, and remove the roof side inner garnish LH.


15. REMOVE ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


16. REMOVE NO. 1 SEAT BRACKET (for Fixed Seat Type)
  1. Remove the 2 nuts and the No. 1 seat bracket.


17. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

  1. B151316
    Remove the bolt and disconnect the floor end of the rear seat inner with center belt assembly LH.


18. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH

  1. B147734
    Remove the bolt and disconnect the floor end of the rear seat outer belt assembly LH.


19. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH

  1. B147735
    Remove the bolt and disconnect the floor end of the rear seat outer belt assembly RH.


20. REMOVE REAR SEAT SHOULDER BELT COVER

  1. B132011E01
    Using a screwdriver, disengage the 4 claws and remove the rear seat shoulder belt cover.

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for the RH side and LH side.


21. REMOVE REAR SEAT SHOULDER BELT HOLE COVER

  1. B132013E02
    Using a screwdriver, disengage the 4 claws and remove the rear seat shoulder belt hole cover.

    HINT:
    Tape the screwdriver tip before use.


22. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)

  1. B132022
    Disconnect the connector.

  1. Disengage the 4 clips and the 5 claws.

  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly, then remove the package tray trim panel assembly.


23. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)

  1. B149208
    Disengage the 2 clips and raise the front portion of the package tray trim panel assembly.

  1. Pass the 3 rear seat belt floor anchors through the holes in the package tray trim panel assembly.

  1. Remove the package tray trim panel assembly.


24. REMOVE NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)

  1. B152699
    Disengage the 4 clips and 5 claws and remove the No. 2 package tray trim panel assembly.


25. REMOVE REAR ASSIST GRIP SUB-ASSEMBLY

HINT:
Use the same procedure for the rear side and the front side.


26. REMOVE SPOT LIGHT ASSEMBLY (w/ Sliding Roof)

  1. B132093E01
    Using a screwdriver, disengage the 2 claws labeled A and 2 claws labeled B from the vehicle body.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a screwdriver, disengage the 2 claws labeled C and remove the spot light assembly from the headlining.

    HINT:
    Tape the screwdriver tip before use.

  1. B132095E01
    Using a screwdriver, disengage the 4 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Pull the light bulb holder in the direction indicated by the arrow in the illustration to detach the claw. Then remove the spot light assembly from the light bulb holder.


27. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining so that the back window glass can be removed (Click here).

28. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining so that the back window glass can be removed (Click here).

29. REMOVE BACK WINDOW MOULDING

  1. B136145E01
    Using a knife, cut off the moulding, as shown in the illustration.

    NOTICE:
    1. Do not damage the vehicle body with the knife.
    2. If the vehicle body is damaged, repair the damaged portion by applying an anti-rust coating after removing the back window glass.

  1. Remove the remaining moulding from the back window glass.

    HINT:
    When removing the moulding, make a partial cut, then pull and remove it by hand.


30. REMOVE BACK WINDOW GLASS ASSEMBLY

NOTICE:
  1. There are No. 1 and No. 2 stoppers on the back window glass as shown in the illustration. Be careful not to damage the back window glass when cutting off the adhesive.
  2. To prevent the back window glass from dropping when performing this operation, be sure to hold the back window glass using suction cups.

HINT:
Depending on vehicles, a 1-piece or 2-piece type stopper is used.


B136146E02

  1. B136148
    Disconnect the connector.

  1. B136149
    Disconnect the connectors.

  1. B136144E01
    Apply protective tape to the installation position of the back window glass assembly on the vehicle body.

    HINT:
    Apply protective tape to the installation surface to prevent it from being scratched.

  1. B136150E01
    Pass a piano wire between the vehicle body and glass from the interior.

  1. Tie both wire ends to wooden blocks or similar objects.

  1. Cut off the adhesive by pulling the piano wire around the back window glass.

    NOTICE:
    1. When separating the back window glass, take care not to damage the paint or the interior and exterior ornaments.
    2. To prevent the package tray from being scratched when removing the back window glass, place a plastic sheet between the piano wire and package tray.

  1. B136147E01
    Place matchmarks on the back window glass and vehicle body on the locations indicated in the illustration.

    HINT:
    Matchmarks do not need to be placed if the back window glass is not going to be reused.

  1. Using a suction cup, remove the back window glass assembly.

    NOTICE:
    1. Be careful not to drop the back window glass.
    2. Leave as much adhesive on the vehicle body as possible when removing the back window glass.


31. REMOVE NO. 2 BACK WINDOW GLASS STOPPER
  1. Using a scraper, remove the 2 No. 2 stoppers.

    NOTICE:
    1. Be careful not to damage the back window glass.
    2. Be sure to replace the No. 2 stoppers with new ones.


32. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)

  1. B136151
    Remove the 2 No. 1 stoppers.

    NOTICE:
    Be sure to replace the No. 1 stoppers with new ones.


33. CLEAN BACK WINDOW GLASS

  1. B149736
    Using a scraper, remove the adhesive tape and adhesive sticking to the back window glass.

    NOTICE:
    Be careful not to damage the back window glass.

  1. Clean the outer circumference of the back window glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the back window glass surface after cleaning it.
    2. Even if using a new back window glass, clean the back window glass with a non-residue solvent.


34. CLEAN VEHICLE BODY

  1. B149737E01
    Clean and shape the contact surface of the vehicle body.

    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.

← COMPONENTS (from Oct 2006)REMOVAL (Oct 2006 – May 2009) →