Install the front door upper window frame moulding to the door frame.
Using an air riveter or hand riveter with a nose piece, install the front door upper window frame moulding with 7 new rivets.
HINT:
If the rivet cannot be cut, pull it once and cut it.
NOTICE:
Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
Confirm that the rivets are seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.
Do not leave any space between the moulding and door frame. Firmly hold together the 2 items while installing the rivet.
2.
INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING
HINT:
When installing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.
Heating temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)
NOTICE:
Do not heat the vehicle body and front door rear window frame moulding excessively.
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Clean the front door rear window frame moulding. (If reusing the front door rear window frame moulding)
Using a heat light, heat the front door rear window frame moulding.
Remove the double-sided tape from the front door rear window frame moulding.
Wipe off any tape adhesive residue with cleaner.
Apply new double-sided tape to the front door rear window frame moulding.
Install the front door rear window frame moulding.
Using a heat light, heat the vehicle body and front door rear window frame moulding.
Remove the release paper from the front door rear window frame moulding.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
Engage the clip and install the front door rear window frame moulding.
3.
INSTALL FRONT DOOR WEATHERSTRIP
Engage the clip and install the front door weatherstrip.
4.
INSTALL FRONT DOOR BELT MOULDING ASSEMBLY
Engage the 2 clips and 5 claws, and install the front door belt moulding assembly.
5.
INSTALL FRONT DOOR GLASS RUN
Install the front door glass run.
6.
INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.
Install the front door glass sub-assembly with the 2 bolts.
Torque:
5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
7.
INSTALL FRONT DOOR SERVICE HOLE COVER
Apply butyl tape to the front door panel.
Pass the front door lock remote control cable and rear door inside locking cable through a new front door service hole cover.
Install the new service hole cover.
NOTICE:
Securely install the front door service hole cover avoiding wrinkles and air bubbles.
Connect each connector and each clamp.
8.
INSTALL OUTER REAR VIEW MIRROR ASSEMBLY
Install the outer rear view mirror assembly with the 3 nuts.
Torque:
4.5 N*m{
46 kgf*cm
, 40 in.*lbf
}
Connect the connector.
9.
INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
Install the front No. 1 speaker assembly with the 4 bolts.
Connect the connector.
10.
INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP
Engage the 4 claws and install the front door inner glass weatherstrip.
11.
INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.
Engage the 2 claws and install the front door inside handle sub-assembly.
12.
INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Connect each connector.
Engage the front door trim board with the 4 clips of the front door inner glass weatherstrip.
Engage the 9 clips and install the front door trim board to the front door panel.
Install the 3 screws and clip (A).
13.
INSTALL ASSIST GRIP COVER
Engage the 6 claws and install the assist grip cover.
14.
INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
Engage the 3 claws and install the front door inside handle bezel plug.
15.
INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH
Engage the 2 clips and install the front door lower frame bracket garnish.