INSTALLATION
Removal / installation · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1. REPAIR INSTRUCTION |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
- Heating temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
- NOTICE:
- Do not heat the vehicle body excessively.
Wipe off any tape adhesive residue with cleaner.
Installation temperature
When ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.
- HINT:
- The most appropriate temperature for installing the tape is 25°C (77°F).
- When the temperature is low, the tape turns stiff and comes off easily. When the temperature is high, the tape loses elasticity.
- The most appropriate temperature for installing the tape is 25°C (77°F).
Before installation
Remove any roughness of coating and dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.
- HINT:
- Spray water on the shop floor to settle any dust.
Key points for handling the tape
The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.
- NOTICE:
- Do not bend the tape or leave it in high temperature places.
Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)
- NOTICE:
- Conduct positioning of the tape with a high accuracy to achieve a neat finish and to avoid peeling.
- The tape cannot be reused because it deforms or does not fit any more after being removed.
- Conduct positioning of the tape with a high accuracy to achieve a neat finish and to avoid peeling.
To avoid air bubbles, slightly raise the part of the tape that are going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (for pressing forward) or 30 to 45° (for pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf) at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.


- NOTICE:
- Be sure to observe the specified pressing speed, force, and angle of the squeegee to avoid wrinkles or air bubbles.
- HINT:
- Either angle of the squeegee (for pressing forward or for pulling) is acceptable.
- Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.
- Either angle of the squeegee (for pressing forward or for pulling) is acceptable.
Key points for installation of the tape (how to use a squeegee and installation procedure for hemming surfaces)
If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

- HINT:
- When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.
Key points for installation of the tape (how to use a squeegee and installation procedure for corners)
Remove the release paper and apply the tape carefully with your fingers.
Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, to avoid wrinkles on the tape and achieve a neat finish.
Check after installation
After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.
- NOTICE:
- Do not reuse the tape.
| 2. INSTALL REAR DOOR LOWER OUTSIDE STRIPE |
Refer to the illustration to position the rear door lower outside stripe.


Remove the release paper and apply the stripe.
| 3. INSTALL REAR DOOR OUTSIDE STRIPE |
- NOTICE:
- Be sure to install the rear door outside stripe after applying the rear door lower outside stripe.
Refer to the illustration to position the rear door outside stripe.


Remove the release paper and apply the stripe.
| 4. INSTALL REAR DOOR FRAME GARNISH |
Engage the clip and install a new rear door frame garnish.

| 5. INSTALL REAR DOOR WEATHERSTRIP |
Engage the clip and install the rear door weatherstrip.

| 6. INSTALL REAR DOOR GLASS RUN |
Install the rear door glass run.

| 7. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
Slide the rear door glass sub-assembly to install it as shown in the illustration.

| 8. INSTALL REAR DOOR QUARTER WINDOW GLASS |
Install the rear door quarter window glass to the rear door quarter window weatherstrip.
Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

| 9. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY |
Insert the rear door lower window frame sub-assembly from above.
Install the rear door glass run to the rear door lower window frame sub-assembly.
Install the rear door lower window frame sub-assembly with the 2 bolts and screw.

| 10. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply butyl tape to the rear door panel.
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

Install the new rear door service hole cover.
- NOTICE:
- Securely install the rear door service hole cover avoiding wrinkles and air bubbles.
Connect the connector and clamp.
| 11. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP |
Engage the 3 claws to install the rear door inner glass weatherstrip.

| 12. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY |
Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle.

Engage the 2 claws and install the rear door inside handle sub-assembly.

| 13. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
Engage the claw to install the No. 1 door scuff plate clamp.

Connect each connector.
Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.

Engage the 7 clips to install the rear door trim board to the rear door panel.

Install the 3 screws.
| 14. INSTALL DOOR ASSIST GRIP COVER |
Engage the 6 claws and install the door assist grip cover.

| 15. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG |
Engage the 3 claws to install the rear door inside handle bezel plug.

