2006-2011 Camry Aurion · Service Manual ENGINE

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


EURO-OBD
When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.
Euro-OBD regulations require that the vehicle's on-board computer illuminates the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:
FI02547E03
  1. The emission control system components.

  2. The power train control components (which affect vehicle emissions).

  3. B139188E08
    The computer
    In addition, if the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory. If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.
    To check DTCs, connect the intelligent tester or OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle.
    The scan tool displays DTCs, the freeze frame data and a variety of engine data.
    The DTCs and freeze frame data can be erased using the scan tool (Click here).


M-OBD
When troubleshooting Multiplex On-Board Diagnostic (M-OBD) vehicle, the vehicle must be connected to the intelligent tester. Various data output from the ECM can then be read.
OBD regulations require that the vehicle's on-board computer illuminates the MIL on the instrument panel when the computer detects a malfunction in:
FI02547E03
  1. The emission control system/components.

  2. The power train control components (which affect vehicle emissions).

  3. The computer
    In addition, the applicable DTCs are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.


NORMAL MODE AND CHECK MODE
The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2-trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1-trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions (intelligent tester only).

2-TRIP DETECTION LOGIC
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected again after the ignition switch is turned off and then to the ON position, the MIL will be illuminated.

DLC3 (Data Link Connector 3)

  1. H100769E16
    The ECM uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format. If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.
    Symbol
    Terminal No.
    Name
    Reference terminal
    Result
    Condition
    SIL
    7
    Bus "+" line
    5 - Signal ground
    Pulse generation
    During transmission
    CG
    4
    Chassis ground
    Body ground
    1 Ω or less
    Always
    SG
    5
    Signal ground
    Body ground
    1 Ω or less
    BAT
    16
    Battery positive
    Body ground
    9 to 14 V
    CANH
    6
    CAN "High" Line
    14 - CANL
    54 to 69 Ω
    Ignition switch off*
    Battery positive
    6 kΩ or higher
    4 - CG
    200 Ω or higher
    CANL
    14
    CAN "Low" Line
    Battery positive
    6 kΩ or higher
    4 - CG
    200 Ω or higher

    NOTICE:
    *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.

    HINT:
    Connect the cable of an intelligent tester to the DLC3, turn the ignition switch to the ON position and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.
    If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
    If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.


INSPECT BATTERY VOLTAGE
If the voltage is below 11 V, replace the battery before proceeding to the next step.

Battery voltage:
11 to 14 V


CHECK MIL
  1. Check that the MIL illuminates when the ignition switch is turned to the ON position.
    If the MIL does not illuminate, there is a problem in the MIL circuit (Click here).

  2. When the engine is started, the MIL should turn off.

← DIAGNOSIS SYSTEM (Jun 2006 – Sep 2006)DIAGNOSIS SYSTEM (from Jun 2009) →