DATA LIST / ACTIVE TEST
System information · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| DATA LIST |
- HINT:
- By reading the Data List displayed on an intelligent tester, you can check values, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step in troubleshooting is one method to shorten diagnostic time.
- NOTICE:
- In the table below, the values listed under Normal Condition are reference only. Do not depend solely on these values when determining whether a part is faulty.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the following menus: Power train / Engine / Data List.
Check the values by referring to the table below.
| Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
| Vehicle Speed |
Vehicle speed: Min.: 0 Km/h, Max.: 255 Km/h |
Actual vehicle speed |
Speed indicated on speedometer |
| Engine Speed |
Engine speed: Min.: 0 rpm, Max.: 16383 rpm: |
600 to 700 rpm: Idling |
- |
| Calculate Load |
Calculated load by ECM: Min.: 0%, Max.: 100% |
|
- |
| Vehicle Load |
Vehicle load: Min.: 0%, Max.: 25700% |
Actual vehicle load |
- |
| MAF |
Air flow rate from mass air flow meter sub-assembly: Min.: 0 gm/sec, Max.: 655.35 gm/sec |
2 to 5 gm/sec: Idling 8 to 19 gm/sec: 2500 rpm |
If value approximately 0.0 gm/sec:
|
| Atmosphere Pressure |
Atmospheric pressure: Min.: 0 KPa, Max.: 255 KPa |
Equivalent to atmospheric pressure (absolute pressure) |
- |
| Coolant Temp |
Engine coolant temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) |
80 to 100°C (176 to 212°F): After warming up |
|
| Intake Air |
Intake air temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) |
Equivalent to ambient air temperature |
|
| Ambient Temperature |
Ambient temperature: Min.: -40°C (-40°F), Max.: 215°C (419°F) |
Actual atmospheric temperature |
- |
| Engine Run Time |
Engine run time: Min.: 0 s, Max.: 65535 s |
Time after engine start |
- |
| Initial Engine Coolant Temp |
Initial engine coolant temperature: Min.: -40°C (-40°F), Max.: 119.3°C (247°F) |
Coolant temperature when engine started |
Service data |
| Initial Intake Air Temp |
Initial intake air temperature: Min.: -40°C (-40°F), Max.: 119.3°C (247°F) |
Intake air temperature when engine started |
Service data |
| Battery Voltage |
Battery voltage: Min.: 0 V, Max.: 65.535 V |
11 to 14 V: Idling |
- |
| Accelerator Position |
Accelerator pedal position: Min.: 0%, Max.: 399.9% |
Actual accelerator pedal position |
- |
| Accel Sens. No. 1 Volt % |
Absolute accelerator pedal position No. 1: Min.: 0%, Max.: 100% |
10 to 22%: Accelerator pedal released 54 to 86%: Accelerator pedal fully depressed |
- |
| Accel Sens. No. 2 Volt % |
Absolute accelerator pedal position No. 2: Min.: 0%, Max.: 100% |
12 to 42%: Accelerator pedal released 66 to 98%: Accelerator pedal fully depressed |
- |
| Accel Sensor Out No. 1 |
Accelerator pedal position sensor No. 1 voltage: Min.: 0 V, Max.: 4.98 V |
- |
- |
| Accel Sensor Out No. 2 |
Accelerator pedal position sensor No. 2 voltage: Min.: 0 V, Max.: 4.98 V |
- |
- |
| Accel Sensor Out No. 1 |
Accelerator pedal position sensor No. 1 voltage: Min.: 0 V, Max.: 4.98 V |
0.5 to 1.1 V: Accelerator pedal released 2.6 to 4.5 V: Accelerator pedal fully depressed |
- |
| Accel Sensor Out No. 2 |
Accelerator pedal position sensor No. 2 voltage: Min.: 0 V, Max.: 4.98 V |
1.2 to 2.0 V: Accelerator pedal released 3.4 to 4.8 V: Accelerator pedal fully depressed |
- |
| Accelerator Idle Position |
Whether or not accelerator pedal position sensor detecting idle: ON or OFF |
ON: Idling |
- |
| Accel Fully Close Learn #1 |
Accelerator fully closed learning value No. 1: Min.: 0 deg, Max.: 124.5 deg |
- |
Electronic throttle control system service data |
| Accel Fully Close Learn #2 |
Accelerator fully closed learning value No. 2: Min.: 0 deg Max.: 124.5 deg |
- |
Electronic throttle control system service data |
| Throttle Sensor Volt % |
Throttle valve opening percentage according to throttle position sensor: Min.: 0%, Max.: 100% |
|
Value calculated based on the voltage at terminal VTA1 |
| Throttl Sensor #2 Volt % |
Throttle valve opening percentage according to throttle position sensor No. 2: Min.: 0%, Max.: 100% |
|
Value calculated based on the voltage at terminal VTA2 |
| ST1 |
Brake pedal signal: ON or OFF |
ON: Brake pedal released |
- |
| System Guard |
System guard: ON or OFF |
- |
Electronic throttle control system service data |
| Open Side Malfunction |
Open side malfunction: ON or OFF |
- |
Electronic throttle control system service data |
| Throttle Idle Position |
Whether or not throttle position sensor detecting idle: ON or OFF |
|
- |
| Throttle Require Position |
Throttle requirement position: Min.: 0 V, Max.: 4.98 V |
0.5 to 1.1 V: Idling |
- |
| Throttle Sensor Position*2 |
Throttle sensor position: Min.: 0%, Max.: 100% |
|
Recognition value for throttle opening angle on ECM |
| Throttle Position No. 1 |
Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 5 V |
- |
- |
| Throttle Position No. 2 |
Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 5 V |
- |
- |
| Throttle Position No. 1 |
Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 5 V |
|
- |
| Throttle Position No. 2 |
Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 5 V |
|
- |
| Throttle Position Command |
Throttle position command value: Min.: 0 V, Max.: 4.980 V |
0.5 to 4.8 V |
- |
| Throttle Sens Open Pos #1 |
Throttle sensor opener position No. 1: Min.: 0 V, Max.: 4.980 V |
0.6 to 1.4 V |
Electronic throttle control system service data |
| Throttle Sens Open Pos #2 |
Throttle sensor opener position No. 2: Min.: 0 V, Max.: 4.980 V |
1.7 to 2.5 V |
Electronic throttle control system service data |
| Throttle Motor Current |
Throttle actuator current: Min.: 0 A, Max.: 19.9 A |
0 to 3.0 A: Idling |
Electronic throttle control system service data |
| Throttle Motor DUTY |
Throttle actuator: Min.: 0%, Max.: 100% |
10 to 22%: Idling after engine warmed up |
Electronic throttle control system service data |
| Throttle Motor Current |
Throttle actuator current: Min.: 0 A, Max.: 19.9 A |
- |
- |
| Throttle Motor Duty (Open) |
Throttle actuator duty ratio (open): Min.: 0%, Max.: 255% |
0 to 40%: Idling |
Electronic throttle control system service data |
| Throttle Motor Duty (Close) |
Throttle actuator duty ratio (close): Min.: 0%, Max.: 255% |
0 to 40%: Idling |
Electronic throttle control system service data |
| Throttle Fully Close Learn |
Throttle valve fully closed (learned value): Min.: 0 V, Max.: 4.98 V |
0.4 to 1.0 V: Accelerator pedal released |
- |
| +BM Voltage |
+BM voltage: Min.: 0 V, Max.: 79.998 V |
11 to 14 V: Ignition switch on (IG) and system normal |
Electronic throttle control system service data |
| Actuator Power Supply |
Throttle actuator power supply: ON or OFF |
|
- |
| Injector (Port) |
Injection period: Min.: 0 μs, Max.: 65535 μs |
1200 to 2400 μs: Idling |
- |
| Injection Volum (Cylinder 1) |
Injection volume (cylinder 1): Min.: 0 ml, Max.: 2.047 ml |
0.05 to 0.15 ml: idling |
Quantity of fuel injection volume for 10 times |
| Fuel Pump/Speed Status |
Fuel pump/status: ON or OFF |
ON: Cranking |
Active Test support data |
| EVAP (Purge) VSV |
Purge VSV control duty: Min.: 0%, Max.: 100% |
0 to 100%: Idling |
Order signal from ECM |
| EVAP Purge Flow |
Purge flow: Min.: 0%, Max.: 399.9% |
0 to 8%: Idling |
Service data |
| Purge Density Learn Value |
Learning value of purge density: Min.: -200, Max.: 199.993 |
-40 to 10: Idling |
Service data |
| EVAP Purge VSV |
Purge VSV status for EVAP control: ON or OFF |
- |
- |
| Purge Cut VSV Duty |
Purge cut VSV duty: Min.: 0%, Max.:399.9% |
- |
- |
| Target Air-Fuel Ratio |
Air fuel ratio: Min.: 0 ,Max.: 1.999 |
0.8 to 1.2: Idling |
- |
| AF Lambda B1S1 |
Short-term fuel trim associated with bank 1 sensor 1: Min.: 0, Max.: 1.999 |
|
- |
| AF Lambda B2S1 |
Short-term fuel trim associated with bank 2 sensor 1: Min.: 0, Max.: 1.999 |
|
- |
| AFS Voltage B1S1 |
Air fuel ratio sensor output voltage for bank 1 sensor 1: Min.: 0 V Max.: 7.999 V |
2.8 to 3.8 V: Idling |
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of air fuel ratio sensor |
| AFS Voltage B2S1 |
Air fuel ratio sensor output voltage for bank 2 sensor 1: Min.: 0 V Max.: 7.999 V |
2.8 to 3.8 V: Idling |
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of air fuel ratio sensor |
| AFS Current B1S1 |
Air fuel ratio sensor current for bank 1 sensor 1: Min.: -128 mA, Max.: 127.99 mA |
- |
- |
| AFS Current B2S1 |
Air fuel ratio sensor current for bank 2 sensor 1: Min.: -128 mA, Max.: 127.99 mA |
- |
- |
| A/F Heater Duty #1 |
Air fuel ratio heater duty ratio for bank 1: Min.: 0%, Max.: 399.9% |
0 to 100% |
- |
| A/F Heater Duty #2 |
Air fuel ratio heater duty ratio for bank 2: Min.: 0%, Max.: 399.9% |
0 to 100% |
- |
| O2S B1S2 |
Heated oxygen sensor output voltage for bank 1 sensor 2: Min.: 0 V Max.: 1.275 V |
0.1 to 0.9 V: Driving at 70 km/h (43 mph) |
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of heated oxygen sensor |
| O2S B2S2 |
Heated oxygen sensor output voltage for bank 2 sensor 2: Min.: 0 V Max.: 1.275 V |
0.1 to 0.9 V: Driving at 70 km/h (43 mph) |
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of heated oxygen sensor |
| O2 Heater B1S2 |
Heated oxygen sensor heater for bank 1 sensor 2: Not Act or Active |
- |
- |
| O2 Heater B2S2 |
Heated oxygen sensor heater for bank 2 sensor 2: Not Act or Active |
- |
- |
| O2 Heater Curr Val B1S2 |
Heated oxygen sensor current for bank 1 sensor 2: Min.: 0 A, Max.: 4.9 A |
- |
- |
| O2 Heater Curr Val B2S2 |
Heated oxygen sensor current for bank 2 sensor 2: Min.: 0 A, Max.: 4.9 A |
- |
- |
| Short FT #1 |
Short-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% |
- 20 to 20% |
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio |
| Long FT #1 |
Long-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% |
- 30 to 30% |
Overall fuel compensation carried out long-term to compensate continual deviation of short-term fuel trim from central value |
| Total FT #1 |
Total fuel trim of bank 1 Average value for fuel trim system of bank 1: Min.: -0.5, Max.: 0.496 |
- 0.28 to 0.2: Idling |
- |
| Short FT #2 |
Short-term fuel trim of bank 2: Min.: -100%, Max.: 99.2% |
- 20 to 20% |
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio |
| Long FT #2 |
Long-term fuel trim of bank 2: Min.: -100%, Max.: 99.2% |
- 30 to 30% |
Overall fuel compensation carried out long-term to compensate continual deviation of short-term fuel trim from central value |
| Total FT #2 |
Total fuel trim of bank 1 Average value for fuel trim system of bank 2: Min.: -0.5, Max.: 0.496 |
- 0.28 to 0.2: Idling |
- |
| Fuel System Status #1 |
Fuel system status (bank 1): OL or CL or OLDrive or OLFault or CL Fault |
CL: Idling after warming up |
|
| Fuel System Status #2 |
Fuel system status (bank 2): OL or CL or OLDrive or OLFault or CL Fault |
CL: Idling after warming up |
|
| IGN Advance |
Ignition timing advance for No. 1 cylinder: Min.: -64 deg, Max.: 63.5 deg |
BTDC 7 to 24 deg: Idling |
- |
| Knock Feedback Value |
Feedback value of knocking: Min.: -1024 CA, Max.: 1023.9 CA |
-22 to 0 CA: Driving at 70 km/h (43 mph) |
Service data |
| Knock Correct Learn Value |
Correction learning value of knocking: Min.: -1024 CA, Max.: 1023.9 CA |
0 to 22 CA: Driving at 70 km/h (43 mph) |
Service data |
| ACIS VSV |
Intake air control valve assembly for acoustic control induction system status: ON or OFF |
ON: Open OFF: Closed |
- |
| AICV VSV |
Vacuum switching valve for air intake control system status: ON or OFF |
- |
- |
| VVT Control Status #1 |
VVT control (bank 1) status: ON or OFF |
- |
- |
| VVT Control Status #2 |
VVT control (bank 2) status: ON or OFF |
- |
- |
| VVT Aim Angle #1*2 |
VVT aim angle (bank 1): Min.: 0%, Max.: 399.9% |
0%: Idling |
VVT duty signal value during intrusive operation |
| VVT Change Angle #1*2 |
VVT change angle (bank 1): Min.: 0 DegFR, Max.: 639.9 DegFR |
0 DegFR: Idling |
Displacement angle during intrusive operation |
| VVT OCV Duty #1*2 |
VVT camshaft timing oil control valve assembly operation duty: Min.: 0%, Max.: 399.9% |
10 to 40%: Idling |
Requested duty value for intrusive operation |
| VVT Aim Angle #2*2 |
VVT aim angle (bank 2): Min.: 0%, Max.: 399.9% |
- |
VVT duty signal value during intrusive operation |
| VVT Change Angle #2*2 |
VVT change angle (bank 2): Min.: 0 DegFR, Max.: 699.9 DegFR |
0 DegFR: Idling |
Displacement angle during intrusive operation |
| VVT OCV Duty #2*2 |
VVT camshaft timing oil control valve assembly (bank 2) operation duty: Min.: 0%, Max.: 399.9% |
0 to 100% |
Requested duty value for intrusive operation |
| VVT Ex Hold Lrn Val #1*2 |
VVT exhaust hold duty ratio learning value (bank 1): Min.: 0%, Max.: 399.9% |
10 to 50%: Idling |
- |
| VVT Ex Chg Angle #1*2 |
VVT exhaust change angle (bank 1): Min.: 0 DegFR, Max.: 699.9 DegFR |
0 to 5 DegFR: Idling |
- |
| VVT Ex OCV Duty #1*2 |
VVT exhaust camshaft timing oil control valve assembly duty (bank 1): Min.: 0%, Max.: 399.9% |
0 to 100% |
- |
| VVT Ex Hold Lrn Val #2*2 |
VVT exhaust hold duty ratio learning value (bank 2): Min.: 0%, Max.: 399.9% |
10 to 50%: Idling |
- |
| VVT Ex Chg Angle #2*2 |
VVT exhaust change angle (bank 2): Min.: 0 DegFR, Max.: 699.9 DegFR |
0 to 5 DegFR: Idling |
- |
| VVT Ex OCV Duty #2*2 |
VVT exhaust camshaft timing oil control valve assembly duty (bank 2): Min.: 0%, Max.: 399.9% |
0 to 100% |
- |
| VN Turbo Type |
Variable nozzle turbo type: Not Avl or Commo or Vacuum or CAN Com |
Not Avl |
- |
| Catalyst Temp B1S1 |
Catalyst temperature (bank 1, sensor 1): Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) |
- |
- |
| Catalyst Temp B2S1 |
Catalyst temperature (bank 2, sensor 1): Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) |
- |
- |
| Catalyst Temp B1S2 |
Catalyst temperature (bank 1, sensor 2): Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) |
- |
- |
| Catalyst Temp B2S2 |
Catalyst temperature (bank 2, sensor 2): Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) |
- |
- |
| Starter Signal |
Starter signal: Open or Close |
Open: Starter signal ON Close: Starter signal OFF |
- |
| Starter Control |
Starter control signal: ON or OFF |
ON: Cranking |
- |
| Power Steering Signal Record |
Power steering signal: ON or OFF |
ON: Power steering operation |
- |
| Starter Relay |
Starter relay: ON or OFF |
ON: Cranking |
- |
| ACC Relay |
ACC relay: ON or OFF |
ON: Cranking |
- |
| Neutral Position SW Signal |
Park/neutral position switch assembly status: ON or OFF |
ON: P or N position |
- |
| Stop Light Switch |
Stop light switch assembly: ON or OFF |
ON: Brake pedal depressed |
- |
| A/C Signal |
A/C signal: ON or OFF |
ON: A/C on |
- |
| Idle Up Signal |
Idle up signal: ON or OFF |
- |
- |
| Closed Throttle Position SW |
Closed throttle position switch: ON or OFF |
|
- |
| Fuel Cut Condition |
Fuel-cut condition: ON or OFF |
ON: Any fuel cut operation executed |
- |
| Check Mode |
Check mode: ON or OFF |
ON: Check mode on |
Click here
|
| SPD Test Result |
Check mode result for vehicle speed sensor: Compl or Incmpl |
- |
- |
| Misfire Test Result |
Check mode result for misfire monitor: Compl or Incmpl |
- |
- |
| OXS1 Test Result |
Check mode result for heated oxygen sensor (bank 1): Compl or Incmpl |
- |
- |
| OXS2 Test Result |
Check mode result for heated oxygen sensor (bank 2): Compl or Incmpl |
- |
- |
| A/F Test Results #2 |
Check mode result for air fuel ratio sensor (bank 2): Compl or Incmpl |
- |
- |
| A/F Test Results #1 |
Check mode result for air fuel ratio sensor (bank 1): Compl or Incmpl |
- |
- |
| Complete Parts Monitor |
Comprehensive component monitor: Not Avl or Avail |
- |
Comprehensive Component Monitor |
| Fuel System Monitor |
Fuel system monitor: Not Avl or Avail |
- |
Fuel System Monitor |
| Misfire Monitor |
Misfire monitor: Not Avl or Avail |
- |
Misfire Monitor |
| EGR/VVT Monitor |
EGR/VVT monitor: Not Avl or Avail |
- |
- |
| EGR/VVT Monitor |
EGR/VVT monitor: Compl or Incmpl |
- |
- |
| O2S (A/FS) Heater Monitor |
Heated oxygen sensor (air fuel ratio sensor) heater monitor: Not Avl or Avail |
- |
- |
| O2S (A/FS) Heater Monitor |
Heated oxygen sensor (air fuel ratio sensor) heater monitor: Compl or Incmpl |
- |
- |
| O2S (A/FS) Monitor |
Heated oxygen sensor (air fuel ratio sensor) monitor: Not Avl or Avail |
- |
- |
| O2S (A/FS) Monitor |
Heated oxygen sensor (air fuel ratio sensor) monitor: Compl or Incmpl |
- |
- |
| A/C Monitor |
A/C monitor: Not Avl or Avail |
- |
- |
| A/C Monitor |
A/C monitor: Compl or Incmpl |
- |
- |
| 2nd Air Monitor |
2nd air monitor: Not Avl or Avail |
- |
- |
| 2nd Air Monitor |
2nd air monitor: Compl or Incmpl |
- |
- |
| EVAP Monitor |
EVAP monitor: Not Avl or Avail |
- |
- |
| EVAP Monitor |
EVAP monitor: Compl or Incmpl |
- |
- |
| Heated Catalyst Monitor |
Heated catalyst monitor: Not Avl or Avail |
- |
- |
| Heated Catalyst Monitor |
Heated catalyst monitor: Compl or Incmpl |
- |
- |
| Catalyst Monitor |
Catalyst monitor: Not Avl or Avail |
- |
- |
| Catalyst Monitor |
Catalyst monitor: Compl or Incmpl |
- |
- |
| TC Terminal |
TC terminal status: ON or OFF |
- |
- |
| # Codes (Include History) |
#Codes: Min.: 0, Max.: 255 |
- |
Number of detected DTCs |
| MIL |
MIL status: ON or OFF |
ON: MIL on |
- |
| MIL ON Run Distance |
MIL on run distance: Min.: 0 Km, Max.: 65535 Km |
Distance after DTC detected |
- |
| Running Time from MIL ON |
Running time from MIL turned on: Min.: 0 min, Max.: 65535 min |
Equivalent to running time after MIL turned on |
- |
| Time after DTC Cleared |
Time after DTC cleared: Min.: 0 min, Max.: 65535 min |
Equivalent to time after DTCs cleared |
- |
| Distance from DTC Cleared |
Distance after DTC cleared: Min.: 0 km, Max.: 65535 km |
Equivalent to drive distance after DTCs cleared |
- |
| Warmup Cycle Cleared DTC |
Warm-up cycle after DTC cleared: Min.: 0, Max.: 255 |
- |
Number of warm-up cycles after DTC cleared |
| Dist Batt Cable Disconnect |
Distance from battery cable disconnect: Min.: 0 Km, Max.: 65535 Km |
- |
- |
| OBD Requirements |
OBD requirement |
E-OBD |
- |
| Number of Emission DTC |
Emission related DTCs: Min.: 0, Max.: 127 |
- |
Number of emission related DTCs |
| TC and TE1 |
TC and TE1 terminals of DLC3: ON or OFF |
- |
Active Test support data |
| Ignition Trig. Count |
Ignition counter: Min.: 0, Max.: 65535 |
0 to 600 |
- |
| Cylinder #1 Misfire Count |
Misfire count of cylinder 1: Min.: 0, Max.: 255 |
0 |
- |
| Cylinder #2 Misfire Count |
Misfire count of cylinder 2: Min.: 0, Max.: 255 |
0 |
- |
| Cylinder #3 Misfire Count |
Misfire count of cylinder 3: Min.: 0, Max.: 255 |
0 |
- |
| Cylinder #4 Misfire Count |
Misfire count of cylinder 4: Min.: 0, Max.: 255 |
0 |
- |
| Cylinder #5 Misfire Count |
Misfire count of cylinder 5: Min.: 0, Max.: 255 |
0 |
- |
| Cylinder #6 Misfire Count |
Misfire count of cylinder 6: Min.: 0, Max.: 255 |
0 |
- |
| All Cylinders Misfire Count |
All cylinders misfire count: Min.: 0, Max.: 255 |
0 to 35 |
- |
| Misfire RPM |
Engine speed for first misfire range: Min.: 0 rpm, Max.: 6375 rpm |
0 rpm: Misfire 0 |
- |
| Misfire Load |
Engine load for first misfire range: Min.: 0 g/rev, Max.: 3.98 g/rev |
0 g/rev: Misfire 0 |
- |
| Misfire Margin |
Misfire monitoring: Min.: -128%, Max.: 127% |
- 100 to 99.22% |
Misfire detecting margin |
| ACM Inhibit |
Duty vacuum switching valve for active control engine mount duty control: ON or OFF |
OFF: Idling |
- |
| ACM |
Duty vacuum switching valve for active control engine mount duty control: Min.: 0%, Max.: 255% |
- |
Active Test support data |
| Electric Fan Motor |
Electric fan motor: ON or OFF |
ON: Electric fan motor operating |
- |
| Idle Fuel Cut Prohibit |
Idle fuel cut prohibit: ON or OFF |
- |
- |
| Idle Fuel Cut |
Fuel cut idle: ON or OFF |
ON: Fuel cut operating |
Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2500 rpm |
| FC TAU |
Fuel cut TAU (Fuel cut during very light load): ON or OFF |
ON: Fuel cut operating |
Fuel cut being performed under very light load to prevent incomplete engine combustion |
| Communication with ECT |
Status of communication with the TCM: Comm or No Comm |
- |
- |
| Electrical Load Signal 1 |
Electrical load signal: ON or OFF |
- |
- |
| Model Code |
Model code |
- |
Identifying model code: GSV40# |
| Engine Type |
Engine type |
- |
Identifying engine type: 2GRFE |
| Cylinder Number |
Cylinder number |
- |
Identifies cylinder number: 6 |
| Transmission Type |
Transmission type |
- |
Identifying transmission type: 6th |
| Destination |
Destination |
- |
Identifies destination: Q or V |
| Model Year |
Model year |
- |
Identifies model year: 200# |
| System Identification |
System identification |
- |
Identifying engine system: Gasoline (gasoline engine) |
| Engine Speed of Cyl #1 |
Engine speed for cylinder 1: Min.: 0 rpm, Max.: 51199 rpm |
- |
Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #2 |
Engine speed for cylinder 2: Min.: 0 rpm, Max.: 51199 rpm |
- |
Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #3 |
Engine speed for cylinder 3: Min.: 0 rpm, Max.: 51199 rpm |
- |
Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #4 |
Engine speed for cylinder 4: Min.: 0 rpm, Max.: 51199 rpm |
- |
Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #5 |
Engine speed for cylinder 5: Min.: 0 rpm, Max.: 51199 rpm |
- |
Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #6 |
Engine speed for cylinder 6: Min.: 0 rpm, Max.: 51199 rpm |
- |
Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Av Engine Speed of All Cyl |
Engine speed for all cylinders: Min.: 0 rpm, Max.: 51199 rpm |
- |
Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Received MIL from ECT |
Received MIL from TCM: ON or OFF |
MIL illuminate instruction ON signal from TCM: ON |
- |
| Shift Position Sig from ECT |
Received shift position signal from TCM: |
Actual shift position |
- |
| A/T Oil Temp from ECT |
Received ATF temperature sensor value from TCM: Min.: -40°C (-40°F), Max.: 215°C (419°F) |
|
If the value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor circuit is open or shorted |
| SPD (NO) |
Output shaft speed: Min.: 0 rpm, Max.: 12750 rpm |
0 rpm: Vehicle stopped |
- |
| SPD (NT) |
Input shaft speed: Min.: 0 rpm, Max.: 12750 rpm |
0 rpm: Vehicle stopped |
- |
| ECT Lock up |
Lock up: ON or OFF |
ON: Lock up operating |
- |
| Shift SW Status (P Range) |
Park/neutral position switch assembly status: ON or OFF |
|
When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (R Range) |
Park/neutral position switch assembly status: ON or OFF |
|
When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (N Range) |
Park/neutral position switch assembly status: ON or OFF |
|
When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Sports Shift Up SW |
Sport shift up switch status: ON or OFF |
|
- |
| Sports Shift Down SW |
Sport shift down switch status: ON or OFF |
|
- |
| Sports Mode Selection SW |
Sport mode select switch status: ON or OFF |
|
- |
| Shift SW Status (D Range) |
Park/neutral position switch assembly status: ON or OFF |
|
When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
- HINT:
- *1: Data List values are only displayed when performing the following Active Tests: Control the VVT Linear (Bank 1), Control the VVT Linear (Bank 2), Control the VVT Exhaust Linear (Bank 1) and Control the VVT Exhaust Linear (Bank 2). For other Active Tests, the Data List value will be 0.
- *2: Excluding throttle valve opening percentage due to idle speed control.
- Normal Condition: If no idling conditions are specified, the transmission gear selector lever should be in the N or P position, and the A/C switch and all accessory switches should be OFF.
- *1: Data List values are only displayed when performing the following Active Tests: Control the VVT Linear (Bank 1), Control the VVT Linear (Bank 2), Control the VVT Exhaust Linear (Bank 1) and Control the VVT Exhaust Linear (Bank 2). For other Active Tests, the Data List value will be 0.
| ACTIVE TEST |
- HINT:
- Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve) and actuators, to be operated without removing any parts. The Active Test can be performed with an intelligent tester. Performing an Active Test as the first step in troubleshooting is one method to shorten diagnostic time.
- Data List can be displayed during Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the following menus: Power train / Engine / Active Test.
Perform the Active Test by referring to the table below.
| Tester Display |
Test Part |
Control Range |
Diagnostic Note |
| Control the Injection Volume |
Change injection volume |
Between -12.5 and 24.8% |
|
| Control the Injection Volume for A/F Sensor |
Change injection volume |
Lower by 12.5% or increase by 25% |
|
| Activate the Fuel Pump Speed Control |
Fuel pump speed control |
ON (low speed) / OFF (high speed) |
Test possible when following conditions met:
|
| Activate the VSV for Intake Control |
ACIS VSV |
ON/OFF |
- |
| Activate the VSV for Evap Control |
Activate VSV for EVAP (ALONE) |
ON/OFF |
Only EVAP VSV is commanded during this test |
| Control the A/C Magnet Clutch |
A/C magnet clutch |
ON/OFF |
- |
| Control the Fuel Pump / Speed |
Activate fuel pump (C/OPN Relay) |
ON/OFF |
- |
| Control the ACM Inhibit |
ACM |
ON/OFF |
- |
| Active the VSV for ACIS |
Active the intake air control valve assembly for ACIS |
ON/OFF |
|
| Connect the TC and TE1 |
Turn on and off TC and TE1 connection |
ON/OFF |
|
| Control the Idle Fuel Cut Prohibit |
Prohibit idling fuel cut control |
ON/OFF |
- |
| Control the ACM Inhibit |
Control the active control engine mount inhibit |
ON/OFF |
- |
| Control the Electric Cooling Fan |
Control Electric Cooling Fan |
ON/OFF |
Test possible when following conditions met:
|
| Activate the Starter Relay |
Activate the starter relay |
ON/OFF |
Engine is stopped |
| Activate the ACC CUT Relay |
Activate the ACC CUT relay |
ON/OFF |
Engine is stopped |
| Control the ETCS Open Slow Speed |
Throttle actuator |
ON: Throttle valve opens slowly |
Test possible when following conditions met:
|
| Control the ETCS Close Slow Speed |
Throttle actuator |
ON: Throttle valve closes slowly |
Same as above |
| Control the ETCS Open Fast Speed |
Throttle actuator |
ON: Throttle valve opens fast |
Same as above |
| Control the ETCS Close Fast Speed |
Throttle actuator |
ON: Throttle valve closes fast |
Same as above |
| Control the VVT Linear (Bank 1) |
Control VVT (bank 1) |
-128 to 127% This valve added to present OCV control duty 100%: Maximum advance -100%: Maximum retard |
Engine stall or rough idle when VVT actuator operated by 100%. Test possible during idle. |
| Control the VVT System (Bank 1) |
Turn on and off OCV (Oil Control Valve) |
ON/OFF |
|
| Control the VVT Linear (Bank 2) |
Control VVT (bank 2) |
Between -128 and 127% |
Same as above |
| Control the VVT System (Bank 2) |
Turn on and off OCV (Oil Control Valve) |
ON/OFF |
|
| Control the VVT Exhaust Linear (Bank 1) |
Control VVT (bank 1) |
-128 to 127% This valve added to present OCV control duty 100%: Maximum retard -100%: Maximum advance |
Engine stall or rough idle when VVT actuator operated by 100%. Test possible during idle. |
| Control the VVT Exhaust Linear (Bank 2) |
Control VVT (bank 2) |
Between -128 and 127% |
Same as above |
| Control the Cylinder #1 Fuel Cut |
Cylinder #1 injector fuel cut |
ON/OFF |
Test possible during vehicle stopping and engine idling. |
| Control the Cylinder #2 Fuel Cut |
Cylinder #2 injector fuel cut |
ON/OFF |
Same as above |
| Control the Cylinder #3 Fuel Cut |
Cylinder #3 injector fuel cut |
ON/OFF |
Same as above |
| Control the Cylinder #4 Fuel Cut |
Cylinder #4 injector fuel cut |
ON/OFF |
Same as above |
| Control the Cylinder #5 Fuel Cut |
Cylinder #5 injector fuel cut |
ON/OFF |
Same as above |
| Control the Cylinder #6 Fuel Cut |
Cylinder #6 injector fuel cut |
ON/OFF |
Same as above |
| Check the Cylinder Compression*1 |
Check the cylinder compression pressure (measuring engine speed foe each cylinder) |
ON/OFF |
Fuel injection and ignition stop in the all cylinders. |
- HINT:
- *1: While the Active Test item Check the Cylinder Compression is being performed, the fuel and ignition of all cylinders is cut. At this time, the ECM measures the speed of each cylinder while the engine is being cranked.
- If one cylinder's speed is higher than the others, that cylinder's compression pressure can be concluded to be lower than the others.
- Warm up the engine.
- Turn the ignition switch off.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch on (IG).
- Turn the tester on.
- Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression.
- HINT:
- If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine / Data List / Engine Speed of Cyl #1 to #6 and Av Engine Speed of All Cyl.
- While the engine is not running, press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.
- HINT:
- After performing the above procedure, the Check the Cylinder Compression Active Test will start. Fuel injection for all cylinders is prohibited, and each cylinder's engine speed measurement will enter standby mode.
- Fully open the throttle.
- Crank the engine for about 10 seconds.
- Monitor the engine speed (Engine Speed of Cyl #1 to #6, Av Engine Speed of All Cyl) displayed on the tester.
- HINT:
- At first, the tester display will show each cylinder's engine speed measurement to be extremely high. After approximately 10 seconds of engine cranking, each cylinder's engine speed measurement will change to the actual engine speed.
- NOTICE:
- After the Check the Cylinder Compression Active Test is turned ON, it will automatically turn OFF after 255 seconds.
- When the Check the Cylinder Compression Active Test is OFF and the engine is cranked, the engine will start.
- If the Check the Cylinder Compression Active Test needs to be performed after it is turned ON and performed once, press EXIT to return to the Active Test menu screen. Then perform the Check the Cylinder Compression Active Test again.
- Use a fully-charged battery.
- After the Check the Cylinder Compression Active Test is turned ON, it will automatically turn OFF after 255 seconds.