2006-2011 Camry Aurion · Service Manual ENGINE

FREEZE FRAME DATA

Troubleshooting · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009


DESCRIPTION
  1. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame date can be helpful in determining whether the vehicle was running or stopped, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.


  1. A103809E18
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using an intelligent tester, 5 separate sets of freeze frame data can be checked.
    1. 3 data sets before the DTC was set.
    2. 1 data set when the DTC was set.
    3. 1 data set after the DTC was set.
    1. These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA
*1: for European spec only
*2: for Automatic transaxle models
*3: with smart entry and start system
Tester Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
The speed indicated on the speedometer.
Engine Speed
Engine speed
-
Calculate Load
Calculated load
The load calculated by the ECM.
Vehicle Load*1
Vehicle load
The load percentage in terms of the maximum intake air flow amount.
MAF
Air flow rate from mass air flow meter
If the value is approximately 0.0 gm/sec.:
  1. The mass air flow meter power source circuit is open.
  1. The VG circuit is open or shorted.
If 271.0 gm/sec. or more:
  1. The E2G circuit is open.
Atmosphere Pressure
Atmospheric pressure
-
Coolant Temp
Engine coolant temperature
  1. If the value is -40°C (-40°F), the sensor circuit is open.
  1. If the value is 140°C (284°F) or higher, the sensor circuit is shorted.
Intake Air
Intake air temperature
  1. If the value is -40°C (-40°F), the sensor circuit is open.
  1. If the value is 140°C (284°F) or higher, the sensor circuit is shorted.
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Initial intake air temperature
-
Battery Voltage
Battery voltage
-
Accel Sens. No. 1 Volt %
Absolute accelerator pedal position No. 1
-
Accel Sens. No. 2 Volt %
Absolute accelerator pedal position No. 2
-
Throttle Sensor Volt %
Absolute throttle position sensor
The throttle opening angle recognized by the ECM.
Read the value with the ignition switch on (IG).
Throttl Sensor #2 Volt %
Absolute throttle position sensor #2
The throttle opening angle recognized by the ECM.
Read the value with the ignition switch on (IG).
Throttle Sensor Position
Throttle sensor positioning
The calculated value based on VTA1.
Read the value with the ignition switch on (IG).
Throttle Motor DUTY
Throttle actuator
-
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder1)
Injection volume (cylinder 1)
The quantity of fuel injection volume for 10 times.
Fuel Pump/Speed Status
Fuel pump/status
-
EVAP (Purge) VSV
EVAP (purge) VSV control duty
The order signal from the ECM.
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Learned value of purge density
-
EVAP Purge VSV
VSV status for EVAP control
-
Target Air-Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1 S1
Fuel trim at air fuel ratio sensor
-
AFS Voltage B1S1
Air fuel ratio sensor output voltage for bank 1 sensor 1
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Current B1S1
Air fuel ratio sensor output current for bank 1 sensor 1
-
O2S B1S2
Heated oxygen sensor output voltage for bank 1 sensor 2
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
Short FT #1
Short-term fuel trim of bank 1
Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric level.
Long FT #1
Long-term fuel trim of bank 1
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #1*1
Total fuel trim of bank 1
-
Fuel System Status #1
Fuel system status (bank 1)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (bank 2)
IGN Advance
Ignition timing advance for No. 1 cylinder
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Learned knocking correction value
-
VVT Control Status #1
VVT control (bank 1) status
-
Catalyst Temp B1S1*1
Estimated catalyst temperature (for sensor 1)
-
Catalyst Temp B1S2*1
Estimated catalyst temperature (for sensor 2)
-
Starter Signal
Starter signal (STA terminal input status)
-
Starter Control*3
Starter control
-
Power Steering Signal Record
Power steering switch status
-
Starter Relay*3
Starter relay status
-
Power Steer. Sig. Record
Power steering signal (history)
-
ACC Relay*3
ACC CUT relay status
-
Neutral Position SW Signal*2
Park/neutral position switch status
-
Stop Light Switch
Stop light switch status
-
A/C Signal
A/C switch status
-
Closed Throttle Position SW
Closed throttle position switch
-
Electrical Load Signal
Electrical load signal
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Total distance vehicle driven after DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
TC and TE1
TC and TE1 terminals of DLC3
-
Ignition Trig. Count*1
Ignition counter to calculated misfire count
-
Cylinder #1 Misfire Count*1
Misfire count of cylinder 1
-
Cylinder #2 Misfire Count*1
Misfire count of cylinder 2
-
Cylinder #3 Misfire Count*1
Misfire count of cylinder 3
-
Cylinder #4 Misfire Count*1
Misfire count of cylinder 4
-
All Cylinders Misfire Count*1
All cylinders misfire count
-
Misfire RPM*1
Average engine speed when misfire occurs
-
Misfire Load*1
Average engine load when misfire occurred
-
Electric Fan Motor
Electric fan motor status
-
Idle Fuel Cut
Fuel cut idle
ON: When the throttle valve is fully closed and the engine speed is more than 1700 rpm.
FC TAU
Fuel cut during very light load
The fuel cut is being performed under a very light load to prevent incomplete engine combustion.
← FREEZE FRAME DATA (Jun 2006 – May 2009)CHECK MODE PROCEDURE (Jun 2006 – May 2009) →