2006-2011 Camry Aurion · Service Manual ENGINE

FREEZE FRAME DATA

Troubleshooting · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


DESCRIPTION
  1. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

    HINT:
    If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.


  1. A103809E17
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
    1. 3 data set before the DTC was set.
    2. 1 data set when the DTC was set.
    3. 1 data set after the DTC was set.
    1. These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying of the cause of the malfunction, and in judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA
Label
(Tester Display)
Measurement Item
Diagnostic Note
Trouble Code
Freeze DTC
-
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed
-
Calculate Load
Calculate load
Calculated load by ECM
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If value approximately 0.0 gm/sec:
  1. Mass air flow meter sub-assembly power source circuit open
  1. VG circuit open or shorted
If value 271.0 gm/sec or more:
  1. E2G circuit open
Atmosphere Pressure
Atmospheric pressure
-
Coolant Temp
Engine coolant temperature
If value -40°C (-40°F), sensor circuit open
If value 140°C (284°F) or more, sensor circuit shorted
Intake Air
Intake air temperature
If value -40°C (-40°F), sensor circuit open
If value 140°C (284°F) or more, sensor circuit shorted
Ambient Temperature
Ambient temperature
-
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Initial engine coolant temperature
-
Initial Intake Air Temp
Initial intake air temperature
-
Battery Voltage
Battery voltage
-
Accel Sens. No. 1 Volt %
Absolute accelerator pedal position No. 1
-
Accel Sens. No. 2 Volt %
Absolute accelerator pedal position No. 2
-
Throttle Sensor Volt %
Throttle position
-
Throttl Sensor #2 Volt %
Throttle sensor positioning #2
-
Throttle Sensor Position
Throttle sensor positioning
-
Throttle Motor DUTY
Throttle actuator
-
Injector (Port)
Fuel injector assembly
-
Injection Volum (Cylinder 1)
Injection volume
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Purge flow
-
Purge Density Learn Value
Learning value of purge density
-
EVAP Purge VSV
EVAP purge VSV
-
Purge Cut VSV Duty
Purge cut vsv duty
-
Target Air-Fuel Ratio
Target air fuel ratio
-
AF Lambda B1S1
Fuel trim at air fuel ratio sensor
-
AF Lambda B2S1
Fuel trim at air fuel ratio sensor
-
AF FT B1S1
Fuel trim at air fuel ratio sensor
-
AF FT B2S1
Fuel trim at air fuel ratio sensor
-
AFS Voltage B1S1
Air fuel ratio sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of air fuel ratio sensor
AFS Voltage B2S1
Air fuel ratio sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of air fuel ratio sensor
AFS Current B1S1
Air fuel ratio sensor current
-
AFS Current B2S1
Air fuel ratio sensor current
-
A/F Heater Duty #1
Air fuel ratio heater duty ratio
-
A/F Heater Duty #2
Air fuel ratio heater duty ratio
-
O2S B1S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of heated oxygen sensor
O2S B2S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of heated oxygen sensor
O2 Heater B1S2
Heated oxygen sensor heater
-
O2 Heater B2S2
Heated oxygen sensor heater
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #1
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value
Total FT #1
Total fuel trim
-
Short FT #2
Short-term fuel trim
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #2
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central valve
Total FT #2
Total fuel trim
-
Fuel System Status #1
Fuel system status (Bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  3. OLDrive: Open loop due to driving conditions (fuel enrichment)
  4. OLFault: Open loop due to detected system fault
  5. CLFault: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning
Fuel System Status #2
Fuel system status (Bank 2)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  3. OLDrive: Open loop due to driving conditions (fuel enrichment)
  4. OLFault: Open loop due to detected system fault
  5. CLFault: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning
IGN Advance
Ignition advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
ACIS VSV
Intake air control valve assembly for acoustic control induction system
-
AICV VSV
Vacuum switching valve for air intake control system
-
VVT Control Status #1
VVT control status (bank 1)
-
VVT Control Status #2
VVT control status (bank 2)
-
Catalyst Temp B1S1
Catalyst temperature
-
Catalyst Temp B2S1
Catalyst temperature
-
Catalyst Temp B1S2
Catalyst temperature
-
Catalyst Temp B2S2
Catalyst temperature
-
Starter Signal
Starter signal
-
Starter Control
Starter control
-
Power Steering Signal Record
Power steering signal
-
Starter Relay
Starter relay
-
ACC Relay
ACC relay
-
Neutral Position SW Signal
Park/neutral position switch assembly signal
-
Stop Light Switch
Stop light switch assembly
-
A/C Signal
A/C signal
-
Idle Up Signal
Idle up signal
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition ON or OFF
-
TC Terminal
TC terminal status
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance after DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
Dist Batt Cable Disconnect
Accumulated distance from battery cable disconnected
-
TC and TE1
TC and TE1 terminals of DLC3
-
Ignition Trig. Count
Ignition count
-
Cylinder #1 Misfire Count
Cylinder #1 misfire count
-
Cylinder #2 Misfire Count
Cylinder #2 misfire count
-
Cylinder #3 Misfire Count
Cylinder #3 misfire count
-
Cylinder #4 Misfire Count
Cylinder #4 misfire count
-
Cylinder #5 Misfire Count
Cylinder #5 misfire count
-
Cylinder #6 Misfire Count
Cylinder #6 misfire count
-
All Cylinders Misfire Count
All cylinder misfire count
-
Misfire RPM
Misfire RPM
-
Misfire Load
Misfire load
-
Misfire Margin
Misfire monitoring
-
ACM Inhibit
Active control engine mount inhibit
-
ACM
Duty vacuum switching valve for active control engine mount duty ratio
-
Electric Fan Motor
Electric fan motor (Cooling fan motor)
-
Idle Fuel Cut Prohibit
Prohibition of fuel cut at idle
-
Idle Fuel Cut
Idle fuel cut
ON: when throttle valve fully closed and engine speed over 2500 rpm
FC TAU
FC TAU
Fuel cut being performed under very light load to prevent incomplete engine combustion
Communication with ECT
Status of the communication with ECT
-
Electrical Load Signal 1
Electrical load signal
-
Received MIL from ECT
MIL status from ECT
-
Shift Position Sig from ECT
Shift position signal from ECT
-
A/T Oil Temp from ECT
ATF temperature from ECT
-
SPD (NO)
Output shaft speed
-
SPD (NT)
Input shaft speed
-
ECT Lock Up
ECT lock up status
-
Shift SW Status (P Range)
Park/neutral position switch assembly status
-
Shift SW Status (R Range)
Park/neutral position switch assembly status
-
Shift SW Status (N Range)
Park/neutral position switch assembly status
-
Sports Shift Up SW
Sport shift up switch status
-
Sports Shift Down SW
Sport shift down switch status
-
Sports Mode Selection SW
Sport mode select switch status
-
Shift SW Status (D Range)
Park/neutral position switch assembly status
-
← FREEZE FRAME DATA (Oct 2006 – May 2009)CHECK MODE PROCEDURE (from Oct 2006) →