2006-2011 Camry Aurion · Service Manual ENGINE

P2118 Throttle Actuator Control Motor Current Range / Performance

Diagnostic trouble codes · Vehicles built Jun 2006 – May 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009

DESCRIPTION

The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (less than 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle actuator.
When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the ignition switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:
The ETCS does not use a throttle cable.

A141490E01
DTC No.
DTC Detection Condition
Trouble Area
P2118
Open in ETCS power source (+BM) circuit
(1-trip detection logic)
  1. Open in ETCS power source circuit
  2. Battery
  3. Battery terminals
  1. ETCS fuse
  1. ECM

FAIL-SAFE

When this DTC, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed gently, the vehicle can be driven slowly. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A141667E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (+BM VOLTAGE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / +BM voltage.

  1. Read the value displayed on the tester.

    Standard voltage:
    9 to 14 V



OK
Go to step 5
NG


2. CHECK FUSE (ETCS FUSE)

  1. A132295E02
    Remove the ETCS fuse from the engine room R/B.

  1. Measure the resistance of the ETCS fuse.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the ETCS fuse.



NG
REPLACE FUSE (ETCS FUSE)
OK


3. CHECK HARNESS AND CONNECTOR (ECM - ETCS FUSE, ETCS FUSE - BATTERY)

  1. A132296E02
    Remove the ETCS fuse from the engine room R/B.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    ETCS fuse (2) - +BM (A24-3)
    Below 1 Ω
    Positive battery cable - ETCS fuse (1)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    ETCS fuse (2) or +BM (A24-3) - Body ground
    10 kΩ or higher
    Positive battery cable or ETCS fuse (1) - Body ground
    10 kΩ or higher

  1. Reinstall the ETCS fuse.

  1. Reconnect the cable to the positive (+) battery terminal.

  1. Reconnect the cable to the negative (-) battery terminal.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


Go to step 5

4. INSPECT ECM (+BM VOLTAGE)

  1. A106902E05
    Disconnect the A24 and C24 ECM connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    +BM (A24-3) - E1 (C24-104)
    9 to 14 V

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (TERMINAL E1 - BODY GROUND)
OK

REPLACE ECM

5. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
REPLACE BATTERY
OK


6. CHECK BATTERY TERMINAL
  1. Check that the battery terminals and ECM ground are not loose or corroded.

    OK:
    Battery terminals and ECM ground are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK

CHECK FOR INTERMITTENT PROBLEMS


← P2111 Throttle Actuator Control System - Stuck Open (+ P2112) (from Jun 2009)P2118 Throttle Actuator Control Motor Current Range / Performance (from Jun 2009) →