2006-2011 Camry Aurion · Service Manual ENGINE

P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit

Diagnostic trouble codes · Vehicles built from Jun 2009

Also covers:

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

CAUTION / NOTICE / HINT

HINT:
  1. These DTCs relate to the Accelerator Pedal Position (APP) sensor.
  2. This ETCS (Electronic Throttle Control System) does not use a throttle cable.


DESCRIPTION

The APP sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals, even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0 V and 5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the APP sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.
A112620E04
DTC No.
DTC Detection Condition
Trouble Area
P2120
VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more
(1-trip detection logic)
  1. APP sensor (built into accelerator pedal assembly)
  1. ECM
P2122
VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal is fully released
(1-trip detection logic)
  1. APP sensor (built into accelerator pedal assembly)
  1. Open in VCP1 circuit
  1. Open or ground short in VPA circuit
  1. ECM
P2123
VPA 4.8 V or more for 2.0 seconds or more
(1-trip detection logic)
  1. APP sensor (built into accelerator pedal assembly)
  1. Open in EPA circuit
  1. ECM
P2125
VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more
(1-trip detection logic)
  1. APP sensor (built into accelerator pedal assembly)
  1. ECM
P2127
VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal is fully released
(1-trip detection logic)
  1. APP sensor (built into accelerator pedal assembly)
  1. Open in VCP2 circuit
  1. Open or ground short in VPA2 circuit
  1. ECM
P2128
Conditions (a) and (b) continue for 2.0 seconds or more (1-trip detection logic):
(a) VPA2 4.8 V or more
(b) VPA between 0.4 V and 3.45 V
  1. APP sensor (built into accelerator pedal assembly)
  1. Open in EPA2 circuit
  1. ECM
P2138
Condition (a) or (b) continues for 2.0 seconds or more (1-trip detection logic):
(a) Difference between VPA and VPA2 is 0.02 V or less
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less
  1. Short between VPA and VPA2 circuit
  1. APP sensor (built into accelerator pedal assembly)
  1. ECM

HINT:
When any of these DTCs are set, check the APP sensor voltage by selecting the following menu items on the intelligent tester: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.
Trouble Area
Accelerator Position No. 1
When AP Released
Accelerator Position No. 2
When AP Released
Accelerator Position No. 1
When AP Depressed
Accelerator Position No. 2
When AP Depressed
VCP circuit open
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
Open or ground short in VPA circuit
0 to 0.2 V
1.2 to 2.0 V
0 to 0.2 V
3.4 to 5.0 V
Open or ground short in VPA2 circuit
0.5 to 1.1 V
0 to 0.2 V
2.6 to 4.5 V
0 to 0.2 V
EPA circuit open
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
Normal condition
0.5 to 1.1 V
1.2 to 2.0 V
2.6 to 4.5 V
3.4 to 5.0 V

HINT:
  1. Accelerator pedal positions are expressed as voltages.
  2. AP denotes Accelerator Pedal.


FAIL-SAFE

When any of DTCs P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 are set, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles. Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

A132297E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION NO. 1 AND ACCELERATOR POSITION NO. 2)

  1. FI07052E18
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.

  1. Read the value displayed on the tester.

    Standard voltage:
    Accelerator Pedal Operation
    Accelerator Position No. 1
    Accelerator Position No. 2
    Released → Depressed → Released
    0.5 to 4.5 V
    1.2 to 5.0 V
    Difference between Accelerator Position No. 1 and Accelerator Position No. 2 is greater than 0.02 V
    Difference between Accelerator Position No. 1 and Accelerator Position No. 2 is greater than 0.02 V



OK
Go to step 5
NG


2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A115665E05
    Disconnect the A17 Accelerator Pedal Position (APP) sensor connector.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VPA (A17-6) - VPA (A24-55)
    Below 1 Ω
    EPA (A17-5) - EPA (A24-59)
    VCPA (A17-4) - VCPA (A24-57)
    VPA2 (A17-3) - VPA2 (A24-56)
    EPA2 (A17-2) - EPA2 (A24-60)
    VCP2 (A17-1) - VCP2 (A24-58)

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VPA (A17-6) or VPA (A24-55) - Body ground
    10 kΩ or higher
    EPA (A17-5) or EPA (A24-59) - Body ground
    VCPA (A17-4) or VCPA (A24-57) - Body ground
    VPA2 (A17-3) or VPA2 (A24-56) - Body ground
    EPA2 (A17-2) or EPA2 (A24-60) - Body ground
    VCP2 (A17-1) or VCP2 (A24-58) - Body ground

  1. Reconnect the APP sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (VCPA AND VCP2 VOLTAGE)

  1. A115666E07
    Disconnect the A17 APP sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    VCPA (A17-4) - EPA (A17-5)
    4.5 to 5.5 V
    VCP2 (A17-1) - EPA2 (A17-2)

  1. Reconnect the APP sensor connector.



NG
REPLACE ECM
OK


4. REPLACE ACCELERATOR PEDAL ASSEMBLY

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM


← P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit (+ 6 more codes) (Oct 2006 – May 2009)P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance (Jun 2006 – Sep 2006) →