2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Wiper and Washer Switch Circuit

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This circuit detects the state of the windshield wiper switch assembly and sends it to the windshield wiper relay assembly (auto wiper relay).

WIRING DIAGRAM

E138726E01

INSPECTION PROCEDURE


1. CHECK WINDSHIELD WIPER SWITCH ASSEMBLY

  1. E194794E01
    Remove the windshield wiper switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E20-2 (+1) - E20-3 (+B)
    MIST
    Below 1 Ω
    LO
    E20-2 (+1) - E20-4 (+S)
    OFF
    E20-3 (+B) - E20-1 (+2)
    HI
    E20-6 (AUTO) - E20-5 (E)
    AUTO
    E20-7 (VR2) - E20-8 (VR1)
    Adjusting right changed from (+) side to (-) side
    0 to 2.7 kΩ



NG
REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY
OK


2. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

  1. E194794E02
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E20-3 (+B) - Body ground
    Engine switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (WIPER SWITCH - AUTO WIPER RELAY, BODY GROUND)

  1. E119091E09
    Disconnect the E26 windshield wiper relay assembly (auto wiper relay) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E20-1 (+2) - E26-3 (+2)
    Always
    Below 1 Ω
    E20-1 (+2) - Body ground
    Always
    10 kΩ or higher
    E20-2 (+1) - E26-1 (+2S)
    Always
    Below 1 Ω
    E20-2 (+1) - Body ground
    Always
    10 kΩ or higher
    E20-3 (+B) - Body ground
    Always
    10 kΩ or higher
    E20-4 (+S) - E26-11 (+SSW)
    Always
    Below 1 Ω
    E20-4 (+S) - Body ground
    Always
    10 kΩ or higher
    E20-5 (E) - E26-16 (CO)
    Always
    Below 1 Ω
    E20-5 (E) - Body ground
    Always
    10 kΩ or higher
    E20-6 (AUTO) - E26-17 (C1)
    Always
    Below 1 Ω
    E20-6 (AUTO) - Body ground
    Always
    10 kΩ or higher
    E20-7 (VR2) - E26-6 (VR2)
    Always
    Below 1 Ω
    E20-7 (VR2) - Body ground
    Always
    10 kΩ or higher
    E20-8 (VR1) - E26-7 (VR1)
    Always
    Below 1 Ω
    E20-8 (VR1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Wiper Motor Power Source Circuit (from Jun 2009)Wiper and Washer Switch Circuit (from Jun 2009) →