2006-2011 Camry Aurion · Service Manual CRUISE CONTROL SYSTEM

DATA LIST / ACTIVE TEST

System information · Vehicles built Jun 2006 – Sep 2006


READ DATA LIST

HINT:
Using the intelligent tester's DATA LIST allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to the ON position.

  3. Read the DATA LIST according to the display on the tester.

    ECM (Cruise control): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Spd
    Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    Memory Spd
    Cruise control memorized speed / min.: 36 km/h (22.5 mph), max.: 200 km/h (125 mph)
    Actual stored vehicle speed
    -
    Throttle
    Throttle opening angle / min.: 0°, max.: 125°
    Actual demanded throttle angle
    -
    Cruise Control
    Cruise control system active condition / ON or OFF
    ON: Cruise control activated
    OFF: Cruise control deactivated
    -
    Main SW (Main)
    Main switch signal (Main CPU) / ON or OFF
    ON: Cruise control main switch on
    OFF: Cruise control main switch off
    "1"
    CCS Ready M
    Cruise control system standby condition (Main CPU) / ON or OFF
    ON/OFF : ON/OFF changes each time main switch is pushed in
    -
    CCS Indicator M
    Cruise indicator signal (Main CPU) / ON or OFF
    ON: "CRUISE" on
    OFF: "CRUISE" off
    -
    Cancel SW
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST SW
    SET / COAST switch signal / ON or OFF
    ON: - (COAST) / SET switch on
    OFF: - (COAST) / SET switch off
    -
    RES/ACC SW
    RES / ACC switch signal / ON or OFF
    ON: + (ACCEL) / RES (RESUME) switch on
    OFF: + (ACCEL) / RES (RESUME) switch off
    -
    Stp Light SW M
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    CCS Oper Status
    PNP switch signal (D position) / ON or OFF
    ON: Shift lever in D
    OFF: Shift lever not in D
    -
    Clutch switch signal / ON or OFF
    ON: Clutch pedal released
    OFF: Clutch pedal depressed
    -

    HINT:
    "1" is OK but CRUISE main indicator light does not illuminate → CRUISE main indicator light, wire harness, or ECM failure


PERFORM ACTIVE TEST

HINT:
Performing the intelligent tester's ACTIVE TEST allows relays, VSVs, actuators, and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to the ON position.

  3. Perform the ACTIVE TEST according to the display on the tester.

    HINT:
    The ignition switch must be turned to the ON position to perform the ACTIVE TEST using the intelligent tester.

    Combination meter: 
    Tester Display
    Test Part
    Control Range
    Normal Condition
    Indicat. Lamp Cruise
    CRUISE main indicator light
    Indicator light BLINK / OFF
    -

← FAIL-SAFE CHART (Jun 2006 – Sep 2006)DIAGNOSTIC TROUBLE CODE CHART (Jun 2006 – Sep 2006) →