2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from Jun 2009


CHECK CLEARANCE WARNING ECU
E102414E02
  1. Disconnect the O30 connector from the clearance warning ECU assembly.

  2. Measure the voltage and check for pulses between each terminal of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O30-1 (PL) - O30-21 (E)
    BR - W-B
    P shift position signal
    Ignition switch on (IG), shift lever in any position except P
    Below 1 V
    Ignition switch on (IG), shift lever in P
    11 to 14 V
    O30-3 (SPD) - O30-21 (E)
    V - W-B
    Vehicle speed signal
    Ignition switch on (IG), vehicle is stopped
    Below 1 V
    Ignition switch on (IG), wheel turned slowly
    Pulse generation (See waveform 1)
    O30-10 (IG) - O30-21 (E)
    B - W-B
    IG signal / IG power source signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    9 to 15 V
    O30-13 (RL) - O30-21 (E)
    R - W-B
    R shift position signal
    Ignition switch on (IG), shift lever in any position except R
    Below 1 V
    Ignition switch on (IG), shift lever in R
    11 to 14 V
    O30-21 (E) - Body ground
    W-B - Body ground
    ECU ground
    Always
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the O30 connector to the clearance warning ECU assembly.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O30-6 (SOR) - O30-21 (E)
    P - W-B
    Back sonar sensor communication signal (LIN communication signal)
    Ignition switch on (IG), clearance sonar main switch on, shift lever in R
    Pulse generation (See waveform 2)
    O30-24 (BOR) - O30-21 (E)
    V - W-B
    Rear sensor circuit power source
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    7.2 to 8.8 V
    O30-12 (BBZ) - O30-21 (E)
    BE - W-B
    Clearance warning buzzer signal
    Buzzer not sounding
    Below 1 V
    Buzzer sounding
    Pulse generation (See waveform 3)
    O30-22 (E2) - O30-21 (E)
    G - W-B
    Rear sensor circuit ground
    Always
    Below 1 V
    If the result is not as specified, the ECU may have a malfunction.

  5. Using oscilloscope:

    1. I043789E01
      Waveform 1 (Reference)
      Item
      Content
      Terminal No.
      (Symbol)
      O30-3 (SPD) - O30-21 (E)
      Tool Setting
      5 V/DIV., 20 msec./DIV.
      Vehicle condition
      Driving at approx. 20 km/h (12 mph)

    2. E159890E01
      Waveform 2 (Reference)
      Item
      Content
      Terminal No.
      (Symbol)
      O30-6 (SOR) - O30-21 (E)
      Tool Setting
      2 V/DIV., 200 μsec./DIV.
      Condition
      Ignition switch on (IG), clearance sonar main switch on, shift lever in R

    3. C139739E03
      Waveform 3 (Reference)
      Item
      Content
      Terminal No.
      (Symbol)
      O30-12 (BBZ) - O30-21 (E)
      Tool Setting
      2 V/DIV., 200 μsec./DIV.
      Buzzer condition
      Buzzer sounding

← PROBLEM SYMPTOMS TABLE (from Jun 2009)ADJUSTMENT (from Jun 2009) →