TERMINALS OF ECU
System information · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| CHECK ENGINE SWITCH |


Disconnect the E52 switch connector.
Measure the resistance according to the value(s) in the table below.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
AGND (E52-8) - Body ground
G - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E52 switch connector.
Measure the resistance and voltage according to the value(s) in the table below.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
AGND (E52-8) - Body ground
G - Body ground
Ground
Always
Below 1 Ω
VC5 (E52-14) - AGND (E52-8)
R - G
Power supply
Key is not in cabin
Below 1 V
Engine switch is pressed
4.6 to 5.4 V
CODE (E52-10) - AGND (E52-8)
W - G
Demodulated signal of key code data
Key is not in cabin
Below 1 V
Engine switch is pressed and key is held close to engine switch*
Pulse generation
(See waveform 1)
TXCT (E52-9) - AGND (E52-8)
GR - G
Key code output signal
Key is not in cabin
Below 1 V
Engine switch is pressed and key is held close to engine switch*
Pulse generation
(See waveform 2)
- HINT:
- *: Remove the key battery before performing this inspection.
- If the result is not as specified, the switch may have a malfunction.
Inspect using an oscilloscope.
Waveform 1 (Reference)

Item
Content
Symbols (Terminal No.)
CODE (E52-10) - AGND (E52-8)
Tool Setting
2 V/DIV., 20 ms./DIV.
Condition
Engine switch is pressed and key is held close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
Waveform 2 (Reference)

Item
Content
Symbols (Terminal No.)
TXCT (E52-9) - AGND (E52-8)
Tool Setting
2 V/DIV., 20 ms./DIV.
Condition
Engine switch is pressed and key is held close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
| CHECK CERTIFICATION ECU |


Disconnect the E58 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
E (E58-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
+B (E58-1) - E (E58-17)
W - W-B
+B power supply
Always
10 to 14 V
IG (E58-18) - E (E58-17)
LG - W-B
Ignition power supply
Engine switch off
Below 1 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E58 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
AGND (E58-40) - Body ground
G - Body ground
Engine switch ground
Always
Below 1 Ω
VC5 (E58-30) - AGND (E58-40)
R - G
Engine switch power supply
Key is not in cabin
Below 1 V
Engine switch is pressed
4.6 to 5.4 V
CODE (E58-9) - AGND (E58-40)
W - G
Engine switch CODE input
Key is not in cabin
Below 1 V
Engine switch is pressed and key is held close to engine switch*
Pulse generation
(See waveform 1)
TXCT (E58-8) - AGND (E58-40)
GR - G
Engine switch TXCT output
Key is not in cabin
Below 1 V
Engine switch is pressed and key is held close to engine switch*
Pulse generation
(See waveform 2)
- HINT:
- *: Remove the key battery before performing this inspection.
- If the result is not as specified, the ECU may have a malfunction.
Inspect using an oscilloscope.
Waveform 1 (Reference)

Item
Content
Symbols (Terminal No.)
CODE (E58-9) - AGND (E58-40)
Tool Setting
2 V/DIV., 20 ms./DIV.
Condition
Engine switch is pressed and key is held close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
Waveform 2 (Reference)

Item
Content
Symbols (Terminal No.)
TXCT (E58-8) - AGND (E58-40)
Tool Setting
2 V/DIV., 20 ms./DIV.
Condition
Engine switch is pressed and key is held close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
| CHECK ID CODE BOX |


Disconnect the E50 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND (E50-8) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
+B (E50-1) - GND (E50-8)
W - W-B
+B power supply
Always
10 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E50 ECU connector.
Measure the voltage according to the value(s) in the table below.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
EFII (E50-5) - GND (E50-8)
G - W-B
ECM input signal
Engine switch off
Below 1 V
Engine switch on (IG)
Pulse generation
(See waveform 1)
EFIO (E50-6) - GND (E50-8)
L - W-B
ECM output signal
Engine switch off
Below 1 V
Engine switch on (IG)
Pulse generation
(See waveform 2)
- If the result is not as specified, the ECU may have a malfunction.
- If the result is not as specified, the ECU may have a malfunction.
Inspect using an oscilloscope.
Waveform 1 (Reference)

Item
Content
Symbols (Terminal No.)
EFII (E50-5) - GND (E50-8)
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Engine switch on (IG)
Waveform 2 (Reference)

Item
Content
Symbols (Terminal No.)
EFIO (E50-6) - GND (E50-8)
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Engine switch on (IG)
| CHECK STEERING CONTROL ECU |


Disconnect the E51 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
SGND (E51-2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
GND (E51-1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
B (E51-7) - Body ground
P - Body ground
+B power supply
Always
10 to 14 V
IG2 (E51-6) - Body ground
B - Body ground
Ignition power supply
Engine switch off
0 V
Engine switch on (IG)
10 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
| CHECK ECM |


Measure the resistance and voltage according to the value(s) in the table below.
for LHD: Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
E1 (C55-81) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
IMI (A55-11) - E1 (C55-81)
Y - W-B
Immobiliser code ECU input signal
Engine switch off
Below 1 V
Engine switch on (IG)
Pulse generation
(See waveform 1)
IMO (A55-10) - E1 (C55-81)
G - W-B
Immobiliser code ECU output signal
Engine switch off
Below 1 V
Engine switch on (IG)
Pulse generation
(See waveform 2)
for RHD: Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
E1 (C58-81) - Body ground*1
E1 (C24-104) - Body ground*2
W-B - Body ground
Ground
Always
Below 1 Ω
IMI (A24-11) - E1 (C58-81)*1
IMI (A24-11) - E1 (C24-104)*2
Y - W-B
Immobiliser code ECU input signal
Engine switch off
Below 1 V
Engine switch on (IG)
Pulse generation
(See waveform 1)
IMO (A24-10) - E1 (C58-81)*1
IMO (A24-10) - E1 (C24-104)*2
G - W-B
Immobiliser code ECU output signal
Engine switch off
Below 1 V
Engine switch on (IG)
Pulse generation
(See waveform 2)
- *1: for 2GR-FE
- *2: for 2AZ-FE
- If the result is not as specified, the ECM may have a malfunction.
- *1: for 2GR-FE
Inspect using an oscilloscope.
Waveform 1 (Reference)

Item
Content
Symbols (Terminal No.)
for LHD
IMI (A55-11) - E1 (C55-81)
for RHD (2GR-FE)
IMI (A24-11) - E1 (C58-81)
for RHD (2AZ-FE)
IMI (A24-11) - E1 (C24-104)
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Engine switch on (IG)
Waveform 2 (Reference)

Item
Content
Symbols (Terminal No.)
for LHD
IMO (A55-10) - E1 (C55-81)
for RHD (2GR-FE)
IMO (A24-10) - E1 (C58-81)
for RHD (2AZ-FE)
IMO (A24-10) - E1 (C24-104)
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Engine switch on (IG)
| CHECK MAIN BODY ECU (INSTRUMENT PANEL J/B) |
Disconnect the IF and IM junction block connectors.
Disconnect the E8, E7, and E6 main body ECU (instrument panel J/B) connectors.


Measure the resistance and voltage according to the value(s) in the table below.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND1 (IF-10) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
GND2 (IM-9) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
GND3 (E8-1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
AM1 (E7-6) - Body ground
L - Body ground
+B power supply
Always
10 to 14 V
AM2 (E6-1) - Body ground
L - Body ground
+B power supply
Always
10 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.