2006-2011 Camry Aurion · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built from Oct 2006


1. REMOVE OIL FILLER CAP SUB-ASSEMBLY
  1. Remove the oil filler cap and gasket.


2. REMOVE SPARK PLUG
  1. Remove the spark plugs.


3. REMOVE OIL PAN DRAIN PLUG

  1. A129654
    Remove the drain plug and gasket.


4. REMOVE VENTILATION VALVE SUB-ASSEMBLY

  1. A129655
    Remove the ventilation valve.


5. REMOVE CAMSHAFT POSITION SENSOR

  1. A129656E05
    Remove the 4 bolts and 4 sensors.


6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A129662E08
    Remove the 4 bolts and 4 oil control valves.


7. REMOVE CRANKSHAFT POSITION SENSOR

  1. A129663
    Remove the bolt and sensor.


8. REMOVE NO. 1 OIL PIPE

  1. A135726E01
    Remove the 2 oil pipe unions and oil pipe.

  1. Remove the oil control valve filter LH and gaskets.


9. REMOVE OIL PIPE

  1. A134878E01
    Remove the bolt.

  1. Remove the 2 oil pipe unions and oil pipe.

  1. Remove the oil control valve filter RH and gaskets.


10. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

  1. A135829E04
    Remove the water drain cocks from the cylinder block.

  1. Remove the water drain cock plugs from the water drain cocks.


11. REMOVE OIL FILTER ELEMENT

  1. A129666
    Remove the drain plug.

    NOTICE:
    Do not remove the O-ring from the oil filter cap.

  1. A129667E01
    Connect the hose to the pipe.

  1. Insert the pipe with the hose into the oil filter cap.

  1. Make sure that the oil is completely drained and remove the pipe and O-ring.

  1. A129668E01
    Using SST, remove the oil filter cap.
    SST
    09228-06501  

  1. A106167E01
    Remove the oil filter element and O-ring from the oil filter cap.

    NOTICE:
    Do not use any tools when removing the O-ring to prevent the O-ring groove from being damaged.


12. REMOVE CRANKSHAFT PULLEY

  1. A120690E02
    Using SST, loosen the crankshaft pulley bolt.
    SST
    09213-70011   (09213-70020)
    09330-00021  

  1. A120691E02
    Using SST, remove the crankshaft pulley bolt and crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


13. REMOVE OIL COOLER ASSEMBLY

  1. A136291
    Remove the bolt, 2 clamps, and 4 clips and disconnect the 2 water by-pass hoses.

  1. A136292
    Remove the union bolt, oil cooler assembly, and O-ring.


14. REMOVE OIL COOLER BRACKET

  1. A136293
    Remove the 3 bolts, 3 nuts, and oil cooler pipe with the oil cooler bracket.

  1. A136294E01
    Remove the bolt, 2 nuts, oil cooler bracket, and gasket.

  1. Using a "TORX" socket wrench E8, remove the 2 stud bolts.


15. REMOVE FRONT ENGINE MOUNTING BRACKET NO. 1 LH

  1. A129672
    Remove the 6 bolts and engine mounting bracket.

  1. Using a "TORX" socket wrench E8, remove the 2 stud bolts.


16. REMOVE WATER INLET HOUSING

  1. A129673
    Remove the 2 nuts, water inlet, and thermostat.

  1. Remove the gasket.

  1. Remove the 2 stud bolts.

  1. Separate the No. 1 water by-pass hose.

  1. A134879E01
    Remove the 2 bolts, nut, and water inlet housing.

  1. Remove the drain cock plug.

  1. Remove the drain cock.

  1. A129675
    Remove the 2 O-rings.


17. REMOVE WATER OUTLET

  1. A129676E01
    Remove the 2 bolts, 4 nuts, and water outlet.

  1. A129677
    Remove the 2 gaskets and O-ring.


18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)

  1. A129679
    Remove the 12 bolts, seal washer, head cover, and gasket.

  1. A129699
    Remove the 3 gaskets.


19. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)

  1. A129678E02
    Remove the 12 bolts, seal washer, head cover, and gasket.

    NOTICE:
    The baffle plate is located on the back of the portion shown in the illustration. Do not damage the baffle plate when removing the head cover.

  1. A129705
    Remove the 3 gaskets.


20. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A129680E01
    Remove the 16 bolts and 2 nuts.

  1. A120816
    Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.

  1. Using a "TORX" socket wrench E6, remove the 2 stud bolts.


21. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A129681
    Remove the bolt, 2 nuts, oil strainer, and gasket.

  1. Using a "TORX" socket wrench E6, remove the 2 stud bolts.


22. REMOVE OIL PAN SUB-ASSEMBLY

  1. A153328E01
    Remove the 16 bolts and 2 nuts.

    HINT:
    Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.

  1. A129683E01
    Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.

  1. A129684
    Remove the 2 O-rings.

  1. Using a "TORX" socket wrench E8, remove the 4 stud bolts.


23. REMOVE OIL PAN BAFFLE PLATE NO.1

  1. A129685
    Remove the 7 bolts and baffle plate.


24. REMOVE ENGINE REAR OIL SEAL RETAINER

  1. A129686
    Remove the 6 bolts.

  1. A129687E01
    Using a screwdriver, pry out the oil seal retainer.

    NOTICE:
    Be careful not to damage the engine rear oil seal retainer.

    HINT:
    Tape the screwdriver tip before use.


25. REMOVE ENGINE REAR OIL SEAL

  1. A131834E02
    Place the oil seal retainer on wooden blocks.

    NOTICE:
    Be careful not to damage the engine rear oil seal retainer.

  1. Using a screwdriver and a hammer, tap out the oil seal.

    HINT:
    Tape the screwdriver tip before use.


26. REMOVE WATER PUMP ASSEMBLY

  1. A129688
    Remove the 16 bolts, water pump, and gasket.


27. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A129689E01
    Remove the 15 bolts and 2 nuts as shown in the illustration.

  1. A129690E02
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block, and chain cover.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 4 bolts, chain cover plate, and gasket.

  1. A128006E01
    Remove the gasket.


28. REMOVE TIMING CHAIN CASE OIL SEAL

  1. A108818E01
    Using a screwdriver, pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.


29. SET NO. 1 CYLINDER TO TDC / COMPRESSION
  1. Temporarily tighten the pulley set bolt.

  1. A129691E01
    Set the timing mark on the crank angle sensor plate to the RH block bore center line (TDC / compression).

  1. A129692E02
    Check that the timing marks of the camshaft timing gears are aligned with those of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°) and align the timing marks as above.


30. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A124589E02
    Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a pin of φ 1.27 mm (0.05 in.) into the stopper plate's hole.

  1. A095165
    Remove the 2 bolts and chain tensioner.


31. REMOVE CHAIN TENSIONER SLIPPER
  1. Remove the chain tensioner slipper.


32. REMOVE CHAIN SUB-ASSEMBLY

  1. A134897E02
    Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.

  1. Remove the pulley set bolt.

  1. A134890
    Remove the chain from the crankshaft timing sprocket and place it on the crankshaft.

  1. A095682E06
    Turn the camshaft timing gear assembly on the bank 1 clockwise (approximately 60°) and set it as shown in the illustration. Be sure to loosen the chain between the banks.

  1. Remove the chain.


33. REMOVE IDLE SPROCKET ASSEMBLY

  1. A137791
    Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, sprocket, and No. 1 idle gear shaft.


34. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A129696
    Remove the 2 bolts and vibration damper.


35. REMOVE NO. 2 CHAIN VIBRATION DAMPER
  1. Remove the 2 vibration dampers.


36. REMOVE CRANKSHAFT TIMING SPROCKET

  1. A109720
    Remove the crankshaft timing sprocket from the crankshaft.

  1. Remove the 2 pulley set keys from the crankshaft.


37. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

  1. A120651E01
    While raising the No. 2 chain tensioner, insert a pin of φ 1.0 mm (0.039 in.) into the hole to fix the No. 2 chain tensioner.

  1. A120652E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts and 2 camshaft timing gear assemblies.

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing gear assemblies.

  1. Remove the No. 2 chain.


38. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A109721
    Remove the bolt and No. 2 chain tensioner.


39. REMOVE CAMSHAFT BEARING CAP (for Bank 1)

  1. A129700E01
    Check that the camshafts are positioned as shown in the illustration.

  1. A129701E03
    Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

  1. A129702E01
    Uniformly loosen and remove the 12 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 bearing caps.


40. REMOVE CAMSHAFT
  1. Remove the camshaft.


41. REMOVE NO. 2 CAMSHAFT
  1. Remove the No. 2 camshaft.


42. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

  1. A129703E01
    Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

    HINT:
    Tape the screwdriver tip before use.


43. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

  1. A120657E01
    While pushing down the No. 3 chain tensioner, insert a pin of φ 1.0 mm (0.039 in.) into the hole to fix the No. 3 chain tensioner.

  1. A120658E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts and 2 camshaft timing gear assemblies.

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing gear assemblies.

  1. Remove the No. 2 chain.


44. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

  1. A109722
    Remove the bolt and No. 3 chain tensioner.


45. REMOVE CAMSHAFT BEARING CAP (for Bank 2)

  1. A129706E01
    Check that the camshafts are positioned as shown in the illustration.

  1. A134891E03
    Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

  1. A129708E01
    Uniformly loosen and remove the 13 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 bearing caps.


46. REMOVE NO. 3 CAMSHAFT
  1. Remove the No. 3 camshaft.


47. REMOVE NO. 4 CAMSHAFT
  1. Remove the No. 4 camshaft.


48. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

  1. A129709E01
    Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

    HINT:
    Tape the screwdriver tip before use.


49. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 24 valve rocker arms.

    HINT:
    Arrange the removed parts in the correct order.


50. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 24 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


51. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH

  1. A129712E01
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head set bolts and plate washers.

    NOTICE:
    1. Be careful not to drop the washers into the cylinder head.
    2. Cylinder head warpage or cracking could result from removing the bolts in an incorrect order.

    HINT:
    Be sure to keep separate the removed parts for each installation position.

  1. Remove the cylinder head and gasket.


52. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

  1. A129710E01
    Uniformly loosen and remove the bolts in the sequence shown in the illustration.

  1. A129711E01
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head set bolts and plate washers.

    NOTICE:
    1. Be careful not to drop the washers into the cylinder head.
    2. Cylinder head warpage or cracking could result from removing the bolts in an incorrect order.

    HINT:
    Be sure to keep separate the removed parts for each installation position.

  1. Remove the cylinder head and gasket.


53. REMOVE WATER INLET PIPE
  1. Separate the No. 1 water by-pass hose.

  1. A153334
    Remove the 2 bolts and water inlet pipe.


54. REMOVE VALVE STEM CAP
  1. Remove the valve stem caps from the cylinder heads.

    HINT:
    Arrange the removed parts in the correct order.


55. REMOVE INTAKE VALVE

  1. A129714E01
    Using SST, compress the compression spring and remove the valve spring retainer locks.
    SST
    09202-70020   (09202-00010)

  1. Remove the retainer, compression spring, and valve.

    HINT:
    Arrange the removed parts in the correct order.


56. REMOVE EXHAUST VALVE

  1. A129715E01
    Using SST, compress the compression spring and remove the valve spring retainer locks.
    SST
    09202-70020   (09202-00010)

  1. Remove the retainer, compression spring, and valve.

    HINT:
    Arrange the removed parts in the correct order.


57. REMOVE VALVE STEM OIL SEAL

  1. A120701E01
    Using needle-nose pliers, remove the oil seals.


58. REMOVE VALVE SPRING SEAT

  1. A120702E01
    Using compressed air and a magnetic finger, remove the valve spring seats by blowing air onto them.


59. REMOVE NO. 1 STRAIGHT SCREW PLUG

  1. A129718E06
    Using a 10 mm hexagon wrench, remove the 4 screw plugs and 4 gaskets.

    NOTICE:
    If water leaks from the straight screw plug or the plug corrodes, replace it.


60. REMOVE NO. 2 STRAIGHT SCREW PLUG

  1. A129719E06
    Using a 14 mm hexagon wrench, remove the screw plugs and gaskets.

    NOTICE:
    If water leaks from the straight screw plug or the plug corrodes, replace it.


61. REMOVE RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.


62. REMOVE STUD BOLT

NOTICE:
If the stud bolt is deformed or the threads are damaged, replace it.


63. REMOVE INTAKE VALVE GUIDE BUSH
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A121839E02
    Using SST and a hammer, tap out the guide bushes.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)


64. REMOVE EXHAUST VALVE GUIDE BUSH
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A120709E02
    Using SST and a hammer, tap out the guide bushes.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)


65. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD
  1. Check that the matchmarks on the connecting rod and cap are aligned.

    HINT:
    The matchmarks on the connecting rods and caps are for ensuring the correct reassembly.

  1. A129760E01
    Remove the 2 connecting rod cap bolts.

  1. A129761
    Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

    HINT:
    Keep the lower bearing inserted to the connecting rod cap.

  1. A129720E01
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearing, connecting rod, and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.


66. REMOVE CONNECTING ROD BEARING

HINT:
Arrange the removed parts in the correct order.


67. REMOVE CRANKSHAFT

  1. A129721E03
    Uniformly loosen and remove the 8 main bearing cap bolts and seal washers in several steps and in the sequence shown in the illustration.

  1. A134892E01
    Uniformly loosen the 16 bearing cap bolts in several steps and in the sequence shown in the illustration.

  1. A122567E01
    Using a screwdriver, pry out the main bearing caps. Remove the 4 main bearing caps and lower bearings.

    NOTICE:
    1. Push up on the cap little by little, from the right and left side alternately so that the cap can be removed.
    2. Be careful not to damage the joint surface of the cylinder block and the main bearing cap.

  1. Remove the crankshaft.


68. REMOVE CRANKSHAFT BEARING

HINT:
Arrange the removed parts in the correct order.


69. REMOVE CRANKSHAFT THRUST WASHER SET

  1. A109726
    Remove the upper bearings and upper thrust washers from the cylinder block.


70. REMOVE PISTON RING SET

  1. A129724E01
    Using a piston ring expander, remove the 2 compression rings.

  1. Remove the oil ring expander and 2 side rails by hand.

    HINT:
    Arrange the removed parts in the correct order.


71. REMOVE PISTON SUB-ASSEMBLY WITH PIN

  1. A129725
    Check the fitting condition between the piston and piston pin.

    1. Try to move the piston back and forth on the piston pin.
      If any movement is felt, replace the piston and pin as a set.

  1. A129726
    Disconnect the connecting rod from the piston.

    1. Using a screwdriver, pry off the snap rings from the piston.

    2. A109729E02
      Gradually heat the piston to approximately 80°C (176°F).

    3. A129728
      Using a brass bar and plastic hammer, lightly tap out the piston pin and remove the connecting rod.

      HINT:
      1. The piston and pin are a matched set.
      2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.

  1. A129729
    Using a gasket scraper, remove the carbon from the piston top.

  1. A129730
    Using a groove cleaning tool or broken ring, clean the piston ring grooves.

  1. A129731
    Using solvent and a brush, thoroughly clean the piston.

    NOTICE:
    Do not use a wire brush.


72. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

  1. A120734
    Using a 5 mm hexagon wrench, remove the bolts and oil nozzles.

  1. Check the 3 oil nozzles for damage or clogging.
    If necessary, replace the oil nozzle.


73. CLEAN CYLINDER BLOCK
← COMPONENTS (from Oct 2006)INSPECTION (from Oct 2006) →