2006-2011 Camry Aurion · Service Manual BODY

TERMINALS OF ECU

System information · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


FRONT POWER SEAT SWITCH RH (POSITION CONTROL ECU)
B107920E20
  1. Disconnect the T20 and T21 ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (T20-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B (T20-5) - GND (T20-1)
    G - W-B
    Power source
    Always
    10 to 14 V
    IG (T21-4) - GND (T20-1)
    B - W-B
    Engine switch signal
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    10 to 14 V
    CANH (T21-5) - CANL (T21-1)
    L - W
    CAN communication line
    Always
    Pulse generation
    SYSB (T21-8) - GND (T20-1)
    W - W-B
    System power source
    Always
    10 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T20 and T21 ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    SLD+ (T20-2) - GND (T20-1)
    L - W-B
    Sliding motor signal (forward)
    Slide switch OFF
    Below 1 V
    Slide switch FRONT ON
    10 to 14 V
    SLD- (T20-3) - GND (T20-1)
    Y - W-B
    Sliding motor signal (rearward)
    Slide switch OFF
    Below 1 V
    Slide switch REAR ON
    10 to 14 V
    FRV+ (T20-6) - GND (T20-1)
    R - W-B
    Front vertical motor signal (upward)
    Front vertical switch OFF
    Below 1 V
    Front vertical switch UP ON
    10 to 14 V
    FRV- (T20-4) - GND (T20-1)
    B - W-B
    Front vertical motor signal (downward)
    Front vertical switch OFF
    Below 1 V
    Front vertical switch DOWN ON
    10 to 14 V
    LFT+ (T20-7) - GND (T20-1)
    W - W-B
    Lifter motor signal (upward)
    Lifter switch OFF
    Below 1 V
    Lifter switch UP ON
    10 to 14 V
    LFT- (T20-9) - GND (T20-1)
    V - W-B
    Lifter motor signal (downward)
    Lifter switch OFF
    Below 1 V
    Lifter switch DOWN ON
    10 to 14 V
    RCL+ (T20-8) - GND (T20-1)
    P - W-B
    Reclining motor signal (forward)
    Reclining switch OFF
    Below 1 V
    Reclining switch FRONT ON
    10 to 14 V
    RCL- (T20-10) - GND (T20-1)
    BR - W-B
    Reclining motor signal (rearward)
    Reclining switch OFF
    Below 1 V
    Reclining switch REAR ON
    10 to 14 V
    If the result is not as specified, the front power seat switch RH (position control ECU) may have a malfunction.


OUTER MIRROR CONTROL ECU
B126261E04
  1. Disconnect the E85 and E86 ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    CAN (E85-1) - CGND (E85-21)
    L - W
    CAN communication line
    Always
    Pulse generation
    MSWE (E85-10) - Body ground
    BE - Body ground
    Ground for seat memory switch
    Always
    Below 1 Ω
    GND (E95-9) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B (E95-3) - GND (E95-9)
    W-R - W-B
    Battery (ECU power source)
    Always
    10 to 14 V
    ACC (E95-4) - GND (E95-9)
    B-R - W-B
    Engine switch (ACC) power source supply
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    10 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E85 and E86 ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M2 (E85-7) - MSWE (E85-10)
    G - BE
    M2 switch signal for seat memory switch
    M2 switch ON
    Below 1 V
    M2 switch OFF
    10 to 14 V
    M1 (E85-8) - MSWE (E85-10)
    P - BE
    M1 switch signal for seat memory switch
    M1 switch ON
    Below 1 V
    M1 switch OFF
    10 to 14 V
    MM (E85-9) - MSWE (E85-10)
    B - BE
    SET switch signal for seat memory switch
    SET switch ON
    Below 1 V
    SET switch OFF
    10 to 14 V
    If the result is not as specified, the outer mirror control ECU may have a malfunction.

← TERMINALS OF ECU (Oct 2006 – May 2009)DIAGNOSIS SYSTEM (from Oct 2006) →