DATA LIST / ACTIVE TEST
System information · Vehicles built from Oct 2006
| READ DATA LIST |
- HINT:
- Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.
Connect the intelligent tester to the DLC3.

Turn the engine switch on (IG).
Read the DATA LIST.
Driver Seat: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Reclin SW Rear
Reclining switch signal (Rearward) / ON or OFF
ON: Reclining switch (Rearward) is ON
OFF: Reclining switch (Rearward) is OFF
-
Reclin SW Front
Reclining switch signal (Forward) / ON or OFF
ON: Reclining switch (Forward) is ON
OFF: Reclining switch (Forward) is OFF
-
F Vtcl SW Down
Front vertical switch signal (Downward) / ON or OFF
ON: Front vertical switch (Downward) is ON
OFF: Front vertical switch (Downward) is OFF
-
F Vtcl SW Up
Front vertical switch signal (Upward) / ON or OFF
ON: Front vertical switch (Upward) is ON
OFF: Front vertical switch (Upward) is OFF
-
Lifter SW Down
Lifter switch (Downward) / ON or OFF
ON: Lifter switch (Downward) is ON
OFF: Lifter switch (Downward) is OFF
-
Lifter SW Up
Lifter switch (Upward) / ON or OFF
ON: Lifter switch (Upward) is ON
OFF: Lifter switch (Upward) is OFF
-
Slide SW Rear
Sliding switch signal (Rearward) / ON or OFF
ON: Sliding switch (Rearward) is ON
OFF: Sliding switch (Rearward) is OFF
-
Slide SW Front
Sliding switch signal (Forward) / ON or OFF
ON: Sliding switch (Forward) is ON
OFF: Sliding switch (Forward) is OFF
-
SET SW
SET switch signal / ON or OFF
ON: SET switch is ON
OFF: SET switch is OFF
-
M1 SW
M1 switch signal / ON or OFF
ON: M1 switch is ON
OFF: M1 switch is OFF
-
M2 SW
M2 switch signal / ON or OFF
ON: M2 switch is ON
OFF: M2 switch is OFF
-
Seat Mem M1
Driving position memorized with M1 switch / MEM or NOT MEM
MEM: Memorized
NOT MEM: Not memorized
-
Seat Mem M2
Driving position memorized with M2 switch / MEM or NOT MEM
MEM: Memorized
NOT MEM: Not memorized
-
IG SW
Communication state of engine switch signal / ON or OFF
ON: Engine switch on (IG) signal is received
OFF: Engine switch on (IG) signal is not received
-
Key SW
Engine switch status (IG) / ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
Key Cord Conf
Recognition code is registered / ON or OFF
ON: One or more recognition codes are registered
OFF: No recognition code is registered
-
DCTY SW
Door courtesy switch signal / ON or OFF
ON: Driver side door is open
OFF: Driver side door is closed
-
P SW
Shift lever position P signal / ON or OFF
ON: Shift lever in P position
OFF: Shift lever in any position other than P
-
PKB SW
Parking brake switch status / ON or OFF
ON: Parking brake is operated
OFF: Parking brake is released
-
Vehicle Spd
Vehicle speed data / MIN.: 0 km/h (0 mph), MAX.: 255 km/h (158 mph)
Actual vehicle speed
-
Power Voltage
Power supply for front power seat switch (position control ECU) / MIN.: 0 V, MAX.: 19.89 V
Within range from 11 to 14 V
-
Slide Pos
Seat sliding position / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
Reclin Pos
Seatback position / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
F Vtcl Pos
Seat front vertical position / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
Lifter Pos
Seat lifter position / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
Slide Mem Pos 1
Seat sliding position memorized with M1 switch / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
Recln Mem Pos 1
Seatback position memorized with M1 switch / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
F Vtcl Mem Pos 1
Seat front vertical position memorized with M1 switch / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
Lifter Mem Pos 1
Seat lifter position memorized with M1 switch / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
Slide Mem Pos 2
Seat sliding position memorized with M2 switch / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
Recln Mem Pos 2
Seatback position memorized with M2 switch / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
F Vtcl Mem Pos 2
Seat front vertical position memorized with M2 switch / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
Lifter Mem Pos 2
Seat lifter position memorized with M2 switch / MIN.: -4096, MAX.: 4096
Within range from -4096 to 4096
-
| PERFORM ACTIVE TEST |
- HINT:
- Performing the intelligent tester's ACTIVE TEST allows a relay, VSV, actuator, and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.
Connect the intelligent tester to the DLC3.

Turn the engine switch on (IG).
Perform the ACTIVE TEST.
Driver Seat: Tester Display
Test Part
Control Range
Diagnostic Note
Reclining
Seat reclining operation
FRONT / REAR
-
F Vertical
Seat front vertical operation
UP / DOWN
-
Lifter
Seat lifter operation
UP / DOWN
-
Slide
Seat sliding operation
FRONT / REAR
-