P0335 Crankshaft Position Sensor "A" Circuit
Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006
Also covers:
- P0339 Crankshaft Position Sensor "A" Circuit Intermittent
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet.The sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0335 |
When either condition below is met:
|
|
| P0339 |
Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1-trip detection logic): (a) Engine speed 1,000 rpm or more (b) Starter signal OFF (c) 3 seconds or more have lapsed since starter signal is switched from ON to OFF |
|
-
Reference: Inspection using an oscilloscope.

- HINT:
- The correct waveform is as shown.
- The correct waveform is as shown.
- G2 stands for the CMP sensor signal, and NE+ stands for the CKP sensor signal.
- Grounding failure of the shielded wire may cause noise in waveforms.
- G2 stands for the CMP sensor signal, and NE+ stands for the CKP sensor signal.
Item
Content
Terminals
CH1: G2+ - G2-
CH2: NE+ - NE-
Equipment Settings
5 V/DIV.
20 ms./DIV.
Conditions
Cranking or idling
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
- Check the engine speed. The engine speed can be checked by using the intelligent tester. Follow the procedure below:
- Connect the intelligent tester to the DLC3.
- Start the engine.
- Turn the tester on.
- Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
- The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the crankshaft position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the CKP sensor output voltage is insufficient.
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
| 1. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
Read the values displayed on the tester while the engine is running.
- OK:
- Correct values are displayed.
- HINT:
- To check the engine speed change, display the graph on the tester.
- If the engine does not start, check the engine speed while cranking.
- If the engine speed indicated on the tester remains zero (0), there may be an open or short in the crankshaft position sensor circuit.
- To check the engine speed change, display the graph on the tester.
|
|
||||
| OK | ||
| ||
| 2. INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE) |
Disconnect the C20 Crankshaft Position (CKP) sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Specified Condition
1 - 2
1,150 to 1,450 Ω
Reconnect the CKP sensor connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the C20 CKP sensor connector.

Disconnect the C24 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
NE+ (C20-1) - NE+ (C24-122)
Below 1 Ω
NE- (C20-2) - NE- (C24-121)
- Standard resistance (Check for short):
Tester Connection
Specified Condition
NE+ (C20-1) or NE+ (C24-122) - Body ground
10 kΩ or higher
NE- (C20-2) or NE- (C24-121) - Body ground
Reconnect the ECM connector.
Reconnect the CKP sensor connector.
|
|
||||
| OK | |
| 4. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
Check the CKP sensor installation condition.

- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 5. CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE) |
Check the teeth of the sensor plate.
- OK:
- Sensor plate does not have any cracks or deformation.
|
|
||||
| OK | |
| 6. REPLACE CRANKSHAFT POSITION SENSOR |
| NEXT | |
| 7. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Display (DTC output)
Proceed to
No output
A
P0335 or P0339
B
- HINT:
- If the engine does not start, replace the ECM.
|
|
||||
| A | ||
| ||
