P0335 Crankshaft Position Sensor "A" Circuit
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Also covers:
- P0339 Crankshaft Position Sensor "A" Circuit Intermittent
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The crankshaft position (CKP) sensor system consists of a crankshaft position sensor plate and a magnetic coil.The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of windings, an iron core and magnet. The sensor plate rotates and as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals for each engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition time are controlled.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0335 |
|
|
| P0339 |
Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection logic): (a) Engine speed 1,000 rpm or more (b) Starter signal OFF (c) 3 seconds or more have elapsed since starter signal switched from ON to OFF |
|
-
Reference: Inspection using an oscilloscope.

- HINT:
- The correct waveform is as shown.
- The correct waveform is as shown.
- VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.
- VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.
Item
Content
Terminals
VV1+ - VV1-
VV2+ - VV2-
NE+ - NE-
Equipment Settings
5 V/DIV,
20 ms./DIV.
Conditions
Cranking or idling
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If no problem is found by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
- Check the engine speed. The engine speed can be checked by using the intelligent tester. To check, follow the procedure below:
- Connect the intelligent tester to the DLC3.
- Start the engine.
- Turn the tester on.
- Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
- The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the crankshaft position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the CKP sensor output voltage is insufficient.
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).
- If no problem is found by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
| 1. INSPECT CRANKSHAFT POSITION SENSOR |
Disconnect the C50 crankshaft position (CKP) sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Cold
1,630 to 2,740 Ω
1 - 2
Hot
2,065 to 3,225 Ω
- HINT:
- Terms "cold" and "hot" refer to the temperature of the coils. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).
Reconnect the CKP sensor connector.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the C50 CKP sensor connector.

Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
- RHD:
Tester Connection
Specified Condition
C50-1 - NE+ (C58-110)
Below 1 Ω
C50-2 - NE- (C58-111)
Below 1 Ω
- LHD:
Tester Connection
Specified Condition
C50-1 - NE+ (C55-110)
Below 1 Ω
C50-2 - NE- (C55-111)
Below 1 Ω
- Standard resistance (Check for short):
- RHD:
Tester Connection
Specified Condition
C50-1 or NE+ (C58-110) - Body ground
10 kΩ or higher
C50-2 or NE- (C58-111) - Body ground
10 kΩ or higher
- LHD:
Tester Connection
Specified Condition
C50-1 or NE+ (C55-110) - Body ground
10 kΩ or higher
C50-2 or NE- (C55-111) - Body ground
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the CKP sensor connector.
|
|
||||
| OK | |
| 3. CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION) |
Check the CKP sensor installation condition.

- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 4. CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE) |
Check the teeth of the sensor plate.
- OK:
- Sensor plate does not have any cracks or deformation.
|
|
||||
| OK | ||
| ||
