2006-2011 Camry Aurion · Service Manual ENGINE

P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built from Jun 2009

Also covers:

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

HINT:
Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.

A three-way catalytic converter (TWC) is used in order to convert the carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxide (Nox) into less harmful substances. To allow the TWC to function effectively, it is necessary to keep the air-fuel ratio of the engine near the stoichiometric air-fuel ratio. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a Heated Oxygen (HO2) sensor is used.
The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V).
Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the HO2 sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.
A088111E15
DTC No.
DTC Detection Condition
Trouble Area
P0136
  1. Abnormal voltage output:
    During active air-fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2-trip detection logic):
    1. (a) Heated Oxygen (HO2) sensor voltage does not decrease to less than 0.21 V
    1. (b) HO2 sensor voltage does not increase to more than 0.59 V
  1. Open or short in HO2 sensor (sensor 2) circuit
  2. HO2 sensor (sensor 2)
  3. HO2 sensor heater (sensor 2)
  4. Air-Fuel Ratio (A/F) sensor (sensor 1)
  5. Engine room J/B (EFI relay)
  6. Gas leakage from exhaust system
P0137
  1. Low voltage (open):
    During active air-fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2-trip detection logic):
    1. (a) HO2 sensor voltage output is less than 0.21 V
    1. (b) Target air-fuel ratio rich
  1. Open in HO2 sensor (sensor 2) circuit
  2. HO2 sensor (sensor 2)
  3. HO2 sensor heater (sensor 2)
  4. Engine room J/B (EFI relay)
  5. Gas leakage from exhaust system
P0138
  1. High voltage (short):
    During active air-fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2-trip detection logic):
    1. (a) HO2 sensor voltage output is 0.59 V or more
    1. (b) Target air-fuel ratio lean
  1. Short in HO2 sensor (sensor 2) circuit
  2. HO2 sensor (sensor 2)
  3. ECM internal circuit malfunction

MONITOR DESCRIPTION

  1. Active Air-Fuel Ratio Control
    The ECM usually performs air-fuel ratio feedback control so that the Air-Fuel Ratio (A/F) sensor output indicates a near stoichiometric air-fuel level. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and Heated Oxygen (HO2) sensor malfunctions (refer to the diagram below).
    Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, one of the following DTCs is set: DTC P0136 (abnormal voltage output), P0137 (open circuit) and P0138 (short circuit).
  1. Abnormal Voltage Output of HO2 Sensor (DTC P0136)
    While the ECM is performing active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the HO2 sensor voltage does not decrease to less than 0.21 V and does not increase to more than 0.59 V during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormal and sets DTC P0136.
    A115540E06
  1. Open or Short in Heated Oxygen (HO2) Sensor Circuit (DTC P0137 or P0138)
    During active air-fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air-fuel ratio to become rich or lean. If the HO2 sensor has an open or short, or the voltage output of the sensor decreases significantly, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air-fuel ratio to become rich or lean, the HO2 sensor output does not change.
    While performing active air-fuel ratio control, when the target air-fuel ratio is rich and the HO2 sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and sets DTC P0137. When the target air-fuel ratio is lean and the voltage output is 0.59 V or more (rich) during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormally high, and sets DTC P0138.

    HINT:
    DTC P0138 is also set if the HO2 sensor voltage output is more than 1.2 V for 10 seconds or more.

    *: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value (Click here).
    A115541E08

WIRING DIAGRAM

A134994E03

CONFIRMATION DRIVING PATTERN

HINT:
  1. This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.
  2. Performing this confirmation pattern will activate the Heated Oxygen (HO2) sensor monitor. (The catalyst monitor is performed simultaneously.) This is very useful for verifying the completion of the repair.

A115372E48
  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch on (IG).
  3. Turn the tester on.
  4. Clear the DTCs (if set) (Click here).
  5. Enter the check mode (Click here).
  6. Select the following menu items: Powertrain / Engine and ECT / Utility.

  7. A126863E01
    Check that "O2 Sensor" is "Incomplete".
  8. Start the engine and warm it up. (Proceed to "A")
  9. Drive the vehicle at between 96 km/h and 113 km/h (60 mph and 70 mph) for at least 10 minutes. (Proceed to "B")
  10. Note the state of the "Utility" items. Those items will change to "Complete" as the O2 Sensor monitor operates.
  11. On the tester, select the following menu items: Powertrain / Engine and ECT / DTC and check if any DTCs (any pending DTCs) are set.

HINT:
If "O2 Sensor" does not change to "Complete", and any pending DTCs fail to set, extend the driving time.


INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the "Control the Injection Volume for A/F Sensor" function provided in the Active Test. The "Control the Injection Volume for A/F Sensor" function can help determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

  1. The following instructions describe how to conduct the "Control the Injection Volume for A/F Sensor" operation using the intelligent tester.
    1. Connect the intelligent tester to the DLC3.
    2. Start the engine and turn the tester on.
    3. Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
    4. On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
    5. Perform the "Control the Injection Volume for A/F Sensor" operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
    6. Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.

HINT:
  1. The "Control the Injection Volume for A/F Sensor" operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. The sensors react in accordance with increases and decreases in the fuel injection volume.


Standard:
Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1 S1
(A/F)
+25%
Rich
Less than 3.0
-12.5%
Lean
More than 3.35
O2S B1 S2
(HO2)
+25%
Rich
More than 0.5
-12.5%
Lean
Less than 0.4

NOTICE:
The A/F sensor has an output delay of a few seconds and the HO2 sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1)
Output Voltage
HO2 Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
-
Output Voltage
More than 3.35 V
Less than 3.0 V
A112626
Output Voltage
More than 0.5 V
Less than 0.4 V
A104057
2
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
Output Voltage
Almost
no reaction
A103185
Output Voltage
More than 0.5 V
Less than 0.4 V
A104057
3
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
Output Voltage
More than 3.35 V
Less than 3.0 V
A112626
Output Voltage
Almost
no reaction
A103185
4
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. Injector
  2. Fuel pressure
  3. Gas leakage from exhaust system
    (Air-fuel ratio extremely lean or rich)
Output Voltage
Almost
no reaction
A103185
Output Voltage
Almost
no reaction
A103185
  1. Following the "Control the Injection Volume for A/F Sensor" procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Enter / View / AFS B1 S1 and O2S B1 S2.

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0138 will be set.


1. READ OUTPUT DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    Proceed to
    P0138
    A
    P0137
    B
    P0136
    C



B
Go to step 14

C
Go to step 7
A


2. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2.

  1. Allow the engine to idle.

  1. Read the Heated Oxygen (HO2) sensor output voltage while idling.

    Result:
    HO2 Sensor Output Voltage
    Proceed to
    More than 1.2 V
    A
    Less than 1.0 V
    B



B
Go to step 5
A


3. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

  1. A107892E63
    Turn the ignition switch off and wait for 5 minutes.

  1. Disconnect the C24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    HT1B (C24-47) - OX1B (C24-64)
    10 kΩ or higher

  1. Reconnect the ECM connector.



NG
Go to step 4
OK

REPLACE ECM

4. INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

  1. A115661E12
    Disconnect the C22 HO2 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    HT1B (1) - +B (2)
    11 to 16 Ω at 20°C (68°F)
    +B (2) - OX1B (3)
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

5. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0138)
  1. On the intelligent tester, select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0138
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS
A

REPLACE HEATED OXYGEN SENSOR

7. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2.

  1. After warming up the engine, run the engine at an engine speed of 2,500 rpm for 3 minutes.

  1. Read the output voltage of the HO2 sensor when the engine rpm is suddenly increased.

    HINT:
    Quickly accelerate the engine to 4,000 rpm 3 times using the accelerator pedal.

    Standard:
    Fluctuates between 0.4 V or less and 0.5 V or more.



NG
Go to step 14
OK


8. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


9. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136)
  1. On the intelligent tester, select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0136
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS
A


10. REPLACE HEATED OXYGEN SENSOR

NEXT


11. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


12. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136)
  1. On the intelligent tester, select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0136
    A
    No output
    B



B
END
A


13. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)

  1. Connect the intelligent tester to the DLC3.A121606E03

  1. Start the engine and turn the tester on.

  1. Warm up the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Change the fuel injection volume using the tester, and monitor the voltage output of Air-Fuel Ratio (A/F) and HO2 sensors displayed on the tester.

HINT:
  1. Change the fuel injection volume within the range of -12% and +12%. The injection volume can be changed in 1% graduations within the range.
  2. The A/F sensor is displayed as AFS B1 S1, and the HO2 sensor is displayed as O2S B1 S2, on the intelligent tester.

    Result:
    Tester Display (Sensor)
    Voltage Variation
    Proceed to
    AFS B1 S1 (A/F)
    Alternates between more and less than 3.3 V
    OK
    Remains at more than 3.3 V
    NG
    Remains at less than 3.3 V
    NG

    HINT:
    A normal HO2 sensor voltage (O2S B1 S2) reacts in accordance with increases and decreases in fuel injection volumes. When the A/F sensor voltage remains at either less or more than 3.3 V despite the HO2 sensor indicating a normal reaction, the A/F sensor is malfunctioning.



NG
REPLACE AIR-FUEL RATIO SENSOR
OK

CHECK AND REPAIR EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO (INJECTOR, FUEL PRESSURE, GAS LEAKAGE FROM EXHAUST SYSTEM, ETC.)

14. INSPECT FOR EXHAUST GAS LEAK

OK:
No gas leakage.



NG
REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT
OK


15. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

  1. A115661E12
    Disconnect the C22 Heated Oxygen (HO2) sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    HT1B (1) - +B (2)
    11 to 16 Ω at 20°C (68°F)
    HT1B (1) - E2 (4)
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR
OK


16. INSPECT ENGINE ROOM J/B (EFI RELAY, EFI MAIN FUSE)

  1. A138917E01
    Inspect the EFI MAIN fuse.
    1. Remove the EFI MAIN fuse from the engine room R/B.

    2. Measure the EFI MAIN fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the EFI MAIN fuse.

  1. Inspect the EFI relay.

    1. Remove the engine room J/B from the engine room R/B.

    2. Measure the EFI relay resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      1E-6 - 1E-12
      10 kΩ or higher
      Below 1 Ω
      (Apply battery voltage between terminals 1E-9 and 1E-11)

    3. Reinstall the engine room J/B.



NG
REPLACE ENGINE ROOM J/B AND/OR EFI MAIN FUSE
OK


17. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

  1. A104950E22
    Disconnect the C22 HO2 sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (C22-2) - Body ground
    9 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the C24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    HT1B (C22-1) - HT1B (C24-47)
    Below 1 Ω
    OX1B (C22-3) - OX1B (C24-64)
    Below 1 Ω
    E2 (C22-4) - EX1B (C24-87)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    HT1B (C22-1) or HT1B (C24-47) - Body ground
    10 kΩ or higher
    OX1B (C22-3) or OX1B (C24-64) - Body ground
    10 kΩ or higher
    E2 (C22-4) or EX1B (C24-87) - Body ground
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.

  1. Reconnect the ECM connector.A133556E09



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HEATED OXYGEN SENSOR


← P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) (+ P0137, P0138) (Oct 2006 – May 2009)P0171 System Too Lean (Bank 1) (+ P0172) (Jun 2006 – Sep 2006) →