Blower Motor Circuit
Circuit diagnosis · Vehicles built from Oct 2006
Versions by build date: Jun 2006 – Sep 2006 from Oct 2006
DESCRIPTION


The blower motor is operated by signals from the A/C amplifier. The blower motor speed is controlled using various duty ratios.
Duty Ratio:
- The duty ratio is the ratio of the blower motor ON time (A) to the total of the blower motor ON and OFF time (A + B).
- The blower motor controller controls the blower motor speed.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Select the item below in the Active Test and then check that the blower motor operates.
| Tester Display |
Test Part |
Control Range |
| Blower Motor (Blower Motor) |
Blower motor / Min.: Level 01, Max.: Level 31 |
- |
- Result:
Result
Proceed to
OK
A
NG (Blower motor does not operate)
B
NG (Blower motor operates but does not change speed)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 2. INSPECT FUSIBLE LINK (HTR) |
Remove the fusible link from the engine room R/B.

Check if the fusible link is melted.

- OK:
- The point indicated by "A" is not melted.
Install the fusible link to the engine room R/B with the nut.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - BODY GROUND) |
Disconnect the blower motor connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E39-1 (GND) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - BATTERY) |
Disconnect the blower motor connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E39-3 (+B) - Body ground
Always
10 to 14 V
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - BLOWER MOTOR) |
Disconnect the A/C amplifier connector.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
(Symbols)
Condition
Specified Condition
E39-2 (SI) - E38-23 (BLW)
Always
Below 1 Ω
E39-2 (SI) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT BLOWER MOTOR |
Reconnect the connector to the blower motor.
Measure the voltage on the A/C amplifier connector side according to the value(s) in the table below.

- Standard voltage:
Tester Connection
Condition
Specified Condition
E38-23 (BLW) - Body ground
Ignition switch on (IG)
4.5 to 5.5 V
|
|
||||
| OK | |
| 7. INSPECT AIR CONDITIONING AMPLIFIER |
Remove the A/C amplifier.
Reconnect the connector to the A/C amplifier.

Turn the ignition switch on (IG).

Turn the blower switch on.
Measure the waveform between terminal E38-23 (BLW) of the A/C amplifier and body ground.
- OK:
- Waveform is as shown in the illustration.
- HINT:
- Waveform varies with the blower level.
| Item |
Contents |
| Tool setting |
1 V/DIV., 500 μs/DIV. |
| Vehicle condition |
Ignition switch on (IG) Blower switch: ON |
|
|
||||
| OK | ||
| ||
