2006-2011 Camry Aurion · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL SPIRAL CABLE (w/ VSC)

  1. C110515E02
    Engage the 6 claws and 2 pins, and install the spiral cable to the steering angle sensor.


2. INSTALL SPIRAL CABLE WITH STEERING ANGLE SENSOR (w/ VSC)
  1. Check that the front wheels are facing straight ahead.

  1. Set the turn signal switch to the neutral position.

    NOTICE:
    If it is not in the neutral position, the pin of the turn signal switch may be snapped.

  1. C133870
    Engage the 3 claws and install the spiral cable with steering angle sensor.

    NOTICE:
    When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly.

  1. Connect the connectors to the spiral cable with steering angle sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


3. INSTALL SPIRAL CABLE (w/o VSC)
  1. Check that the front wheels are facing straight ahead.

  1. Set the turn signal switch to the neutral position.

    NOTICE:
    If it is not in the neutral position, the pin of the turn signal switch may be snapped.

  1. C133870
    Engage the 3 claws and install the spiral cable.

    NOTICE:
    When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly.

  1. Connect the connectors to the spiral cable.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


4. INSTALL UPPER STEERING COLUMN COVER

  1. C145842
    Engage the claw to install the upper steering column cover.


5. INSTALL LOWER STEERING COLUMN COVER

  1. C145841
    Engage the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }


6. ADJUST SPIRAL CABLE
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C107193
    Rotate the spiral cable counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.

  1. C107194E01
    Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.


7. INSTALL STEERING WHEEL ASSEMBLY

  1. C145840E01
    Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.


8. INSPECT STEERING WHEEL CENTER POINT

9. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C133859E01
    Support the steering pad with one hand.

  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. C146015E01
    Using a "TORX" socket (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }


10. INSTALL NO. 3 LOWER STEERING WHEEL COVER

  1. Engage the claw and install the No. 3 lower steering wheel cover.

    C146016E01


11. INSTALL NO. 2 LOWER STEERING WHEEL COVER

  1. Engage the claw and install the No. 2 lower steering wheel cover.

    C146017E01


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

13. INSPECT STEERING PAD

  1. C146010E01
    With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).


14. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).

← INSTALLATION (Jun 2006 – Sep 2006)INSTALLATION (from Jun 2009) →