2006-2011 Camry Aurion · Service Manual RESTRAINTS

REMOVAL

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

HINT:
  1. Use the same procedure for the RHD driver side and LHD driver side.
  2. The procedure listed below are for LHD driver side.


1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Seat)

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.


3. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)

4. REMOVE OUTER SEAT TRACK BRACKET COVER LH (for Manual Seat)
  1. Move the front seat assembly fully forward by operating the slide handle.

  1. B149587
    Using a screwdriver, disengage the 4 claws and remove the outer seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


5. REMOVE INNER SEAT TRACK BRACKET COVER LH (for Manual Seat)

  1. B149588
    Using a screwdriver, disengage the 4 claws and remove the inner seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


6. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)
  1. Move the front seat assembly to the rearmost position by operating the slide handle.

  1. B139101
    Remove the 2 bolts on the front seat track bracket.

  1. Move the front seat assembly fully forward by operating the slide handle.

  1. B139102
    Remove the 2 bolts on the rear seat track bracket.

  1. Move the front seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and reclining adjuster release handle.

  1. Disconnect the connectors and clamp.

  1. Remove the front seat assembly.


7. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Power Seat)

8. REMOVE OUTER SEAT TRACK BRACKET COVER LH (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the position farthest forward.

  1. B149587
    Using a screwdriver, detach the 4 claws and remove the outer seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


9. REMOVE INNER SEAT TRACK BRACKET COVER LH (for Power Seat)

  1. B149588
    Using a screwdriver, detach the 4 claws and remove the inner seat track bracket cover.


10. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B149590
    Remove the 2 bolts on the front seat track bracket.

  1. Operate the power seat switch knob and move the seat to the position farthest forward.

  1. B139102
    Remove the 2 bolts on the rear seat track bracket.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).

  1. Disconnect the connectors under the seat. Then remove the front seat assembly.


11. REMOVE VERTICAL ADJUSTER COVER LH (for Manual Seat)

  1. B139103
    Using a screwdriver, disengage the 2 claws and remove the vertical adjuster cover LH.

    HINT:
    Tape the screwdriver tip before use.


12. REMOVE VERTICAL ADJUSTING HANDLE (for Manual Seat)

  1. B139104
    Remove the 2 screws and vertical adjusting handle.


13. REMOVE RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)

  1. B139105
    Lift the reclining adjuster release handle.

  1. Using a screwdriver, disengage the claw and remove the reclining adjuster release handle.

    HINT:
    Tape the screwdriver tip before use.


14. REMOVE FRONT SEAT CUSHION SHIELD (for Manual Seat)

  1. B153813
    Disengage the 2 hooks.

  1. B149580
    Remove the 2 screws.

  1. Disengage the 2 claws and separate the front seat cushion shield.

  1. Disconnect the connector from the front power seat lumbar switch. (w/ lumber support)


15. REMOVE SEAT POSITION SENSOR (for Manual Seat)

  1. C133900
    Disconnect the connector.

  1. Using a "TORX" socket (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.

  1. C133901
    Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.


16. REMOVE SEAT POSITION SENSOR (for Power Seat)

  1. C133891
    Disconnect the connector.

  1. Using a "TORX" socket (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.

  1. C133892
    Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.

← ON-VEHICLE INSPECTION (from Jun 2009)REMOVAL (Oct 2006 – May 2009) →