REMOVAL
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1.
PRECAUTION |
 |
- CAUTION:
- Be sure to read "PRECAUTION" thoroughly before servicing (Click here).
| 2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
 |
- CAUTION:
- Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
| 3.
REMOVE FRONT DOOR SCUFF PLATE LH
|
 |
- Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
| 4.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
|
 |
- Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 5.
REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
|
 |
- Remove the bolt <D> and the screw <F>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect each connector, and then remove the lower No. 1 instrument panel finish panel.
| 6.
REMOVE FRONT DOOR SCUFF PLATE RH |
 |
- HINT:
- Use the same procedure for the RH and LH side (Click here).
| 7.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
 |
- HINT:
- Use the same procedure for the RH and LH side (Click here).
| 8.
REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY
|
 |
- Disengage the 4 claws.
Disengage the 2 guides and remove the No. 2 under cover sub-assembly.
| 9.
REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
|
 |
- Remove the bolt <D>.
Remove the screw <F> or <N>.
Remove the 3 screws <F>.
Disengage the 3 claws and the 3 clips, and then remove the lower instrument panel sub-assembly.
| 10.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
|
 |
- Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 11.
REMOVE UPPER CONSOLE PANEL FRONT GARNISH
|
 |
- Apply protective tape to the area shown in the illustration.
- Using a moulding remover, disengage the 3 claws as shown in the illustration.
- Using a moulding remover, disengage the 3 claws and remove the upper console panel front garnish as shown in the illustration.
Disconnect each connector.
| 12.
REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY
|
 |
- Apply protective tape to the area shown in the illustration.
- Using a moulding remover, disengage the 2 claws as shown in the illustration.
- Apply protective tape to the area shown in the illustration.
- Using a moulding remover, disengage the 2 claws as shown in the illustration.
- Disengage the 6 claws and remove the upper console panel sub-assembly as shown in the illustration.
Disconnect the connector.
| 13.
REMOVE CONSOLE BOX CARPET
|
 |
- Remove the console box carpet.
| 14.
REMOVE CONSOLE BOX ASSEMBLY
|
 |
- Disengage the clamp.
- Remove the 3 screws <H>.
- Remove the 3 screws <H>.
- Remove the 2 bolts <I>.
- Disengage the 2 claws and remove the console box assembly.
| 15.
REMOVE FLOOR CARPET BRACKET LH
|
 |
- Release the clamp.
Turn back the floor carpet.
- Remove the 3 clips.
Remove the floor carpet bracket LH.
| 16.
REMOVE FLOOR CARPET BRACKET RH
|
 |
- Release the clamp.
Turn back the floor carpet.
- Remove the 3 clips.
Remove the floor carpet bracket RH.
| 17.
REMOVE NO. 1 CONSOLE BOX DUCT
|
 |
- Remove the clip and No. 1 console box duct.
| 18.
REMOVE CENTER AIRBAG SENSOR ASSEMBLY |
 |
Turn back the carpet.
- Disconnect the holder (with connectors).
Remove the 3 bolts and center airbag sensor assembly.