Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 3 clips.
Using a moulding remover, disengage the 4 clips.
Disconnect the connector and remove the instrument panel No. 2 register assembly.
36.
REMOVE RADIO AND CASSETTE TAPE WITH HEATER CONTROL PANEL ASSEMBLY (w/o CD Player)
Remove the 4 bolts.
Pull the radio and cassette tape with heater control panel assembly toward the rear of the vehicle and disengage the 6 clips.
Disconnect each connector and remove the radio and cassette tape with heater control panel assembly.
37.
REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ CD Player)
Remove the 4 bolts.
Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the radio receiver with heater control panel assembly.
38.
REMOVE NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System)
Remove the 4 bolts.
Pull the navigation receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the navigation receiver with heater control panel assembly.
39.
REMOVE CONSOLE BOX POCKET
Remove the console box pocket.
40.
REMOVE CONSOLE BOX CARPET
Remove the console box carpet.
41.
REMOVE CONSOLE BOX ASSEMBLY
Remove the 2 screws <F>.
Disengage the clamp.
Remove the 2 bolts <G> and the console box assembly.
42.
REMOVE NO. 2 CONSOLE BOX INSERT FRONT
Remove the 3 screws <F>.
Disengage the clip and remove the No. 2 console box insert front.
43.
REMOVE NO. 1 CONSOLE BOX INSERT FRONT
Remove the 3 screws <F>.
Disengage the clip and remove the No. 1 console box insert front.
44.
REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish LH.
Remove the clip <A> from the vehicle body.
45.
REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish LH.
Remove the clip <A> from the vehicle body.
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
Remove the 2 bolts and front No. 2 speaker assembly.
Disconnect the connector.
49.
REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish RH.
Remove the clip <A> from the vehicle body.
50.
REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish RH.
Remove the clip <A> from the vehicle body.
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.