2006-2011 Camry Aurion · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

CAUTION:
Wear protective gloves. Sharp areas on the seat adjuster may injure your hands.


1. INSTALL FRONT SEAT WIRE
  1. Engage the each claw and each clamp and install the front seat wire.


2. INSTALL SEAT POSITION SENSOR (for Driver Side)
  1. Check that the ignition switch is off.

  1. Check that the negative battery (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C133893E01
    Engage the pin and install the seat position sensor to the seat slide position sensor protector as shown in the illustration.

  1. C107067E08
    Using a 1.0 mm (0.039 in.) feeler gauge, temporarily install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).

  1. C133891
    Using a "TORX" socket (T30), tighten the "TORX" screw to install the seat position sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).

  1. Check that there is no looseness in the installation parts of the seat position sensor.

  1. Connect the connector.


3. INSTALL FRONT SEPARATE TYPE SEATBACK SPRING ASSEMBLY

  1. B148636
    Install the front separate type seatback spring assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B148635E01
    Connect the 2 clamps and connector.


4. INSTALL FRONT LOWER SEAT CUSHION SHIELD

  1. B148634
    Engage the 2 claws.

  1. Install the front lower seat cushion shield with the screw.


5. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH

  1. B148633
    Engage the 2 claws.

  1. Install the front lower seat cushion shield LH with the screw.


6. INSTALL SEAT RECLINING ADJUSTER INSIDE COVER LH

  1. B148632
    Engage the claw.

  1. Install the seat reclining adjuster inside cover LH with the screw.


7. INSTALL SEAT RECLINING ADJUSTER INSIDE COVER RH

  1. B148631
    Engage the claw.

  1. Install the seat reclining adjuster inside cover RH with the screw.


8. INSTALL RECLINING ADJUSTER INSIDE COVER LH

  1. B148653
    Install the reclining adjuster inside cover LH with the screw.


9. INSTALL RECLINING ADJUSTER INSIDE COVER RH

  1. B148652
    Install the reclining adjuster inside cover RH with the screw.


10. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY

  1. B146666E01
    Install the lumbar support adjuster assembly with the 2 screws.

  1. Connect the connector.


11. INSTALL FRONT SEPARATE TYPE SEATBACK COVER

  1. B136592E01
    Using hog ring pliers, install the front separate type seatback cover to the front seatback pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


12. INSTALL FRONT SEATBACK ASSEMBLY (w/o Airbag System)
  1. Install the front seatback assembly to the front seatback spring assembly.

  1. B136594E01
    Engage the 3 hooks.

  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


13. INSTALL FRONT SEATBACK ASSEMBLY (w/ Airbag System)
  1. Install the front seatback assembly to the front seatback spring assembly.

  1. B153817
    Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
    2. Make sure that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.

  1. B136594E01
    Engage the 3 hooks.

  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


14. INSTALL FRONT SEAT HEADREST SUPPORT

  1. B134683
    Engage the 2 claws to install the front seat headrest support.

    HINT:
    Use the same procedure for the RH side and LH side.


15. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY

  1. B134682E02
    Engage the 2 claws.

  1. Engage the 14 claws.

  1. Install the front seatback board sub-assembly with the 2 screws.


16. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER

  1. B136593E01
    Using hog ring pliers, install the front separate type seat cushion cover to the front separate type seat pad with 16 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


17. INSTALL FRONT SEAT CUSHION ASSEMBLY

  1. B146658E01
    Engage the hooks.

  1. B146657
    Engage the 4 hooks.

  1. Connect the connector.


18. INSTALL POWER SEAT SWITCH

  1. B149586
    Connect the connector.

  1. Install the power seat switch with the 3 screws.


19. INSTALL FRONT INNER SEAT CUSHION SHIELD

  1. B146655
    Install the front inner seat cushion shield with the screw.

  1. Engage the 3 claws.


20. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B258139E01
    for LHD:

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. Connect the connector.

    3. B258132E01
      Connect the connector and engage each clamps.

    4. B147624
      Engage the 2 hooks.

  1. for RHD:

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. Connect the connector. (for Driver seat)

      B151324E01

    3. B151313E01
      Connect the connector and engage the 2 clamps.

    4. B152833
      Engage the 2 hooks.


21. INSTALL FRONT POWER SEAT LUMBAR SWITCH

  1. B146654
    Install the front power seat lumbar switch with the 2 screws.


22. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD

  1. B146653
    Install the front inner No. 1 seat cushion shield with the 2 screws.

  1. Engage the 2 claws.


23. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY

  1. B134673
    Connect the connector.

  1. Engage the 2 claws.

  1. Install the front seat cushion shield assembly with the 5 screws.

  1. B146651
    Install the 2 rubber bands on the backside of the front seatback board sub-assembly.


24. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

  1. B149597
    Install the slide and vertical power seat switch knob.


25. INSTALL RECLINING POWER SEAT SWITCH KNOB

  1. B149596
    Install the reclining power seat switch knob.

← REASSEMBLY (Oct 2006 – May 2009)INSTALLATION (Jun 2006 – Sep 2006) →