P0711 Transmission Fluid Temperature Sensor "A" Performance
Diagnostic trouble codes · Vehicles built from Oct 2006
DESCRIPTION
The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value for use by the TCM.

The TCM applies a voltage to the temperature sensor through terminal THO1 of the TCM.
The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.
The TCM calculates the fluid temperature based on the voltage signal.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0711 |
|
|
MONITOR DESCRIPTION
This DTC indicates that there is a problem with output signals from the automatic transmission fluid (ATF) temperature sensor (TFT sensor) and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature and detects an open or short in the ATF temperature circuit or a fault of the ATF temperature sensor.After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the TCM interprets this as a fault, and turns on the MIL.
WIRING DIAGRAM


INSPECTION PROCEDURE
| DATA LIST |
- HINT:
- According to the Data List displayed on the intelligent tester, you can read the value of switches, sensors, actuators and other items without removing any parts. Reading the Data List as the first step in troubleshooting is one method to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Enter the following items: "Powertrain / ECT / Data List".
According to the display on the tester, read "Data List".
Tester Display
Measurement Item/Range
Normal Condition
A/T Oil Temperature 1
ATF Temperature Sensor Value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After Stall Test;
Approx. 80°C (176°F)
- Equal to ambient temperature when cold soak
- HINT:
- When DTC P0712 is output and the intelligent tester indicates 150°C (302°F) or more, there is a short circuit.
- When DTC P0712 is output and the intelligent tester indicates 150°C (302°F) or more, there is a short circuit.
- When DTC P0713 is output and the intelligent tester indicates -40°C (-40°F), there is an open circuit.
- When DTC P0713 is output and the intelligent tester indicates -40°C (-40°F), there is an open circuit.
- Measure the resistance between terminal THO1 and body ground.
- Measure the resistance between terminal THO1 and body ground.
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
150°C (302°F) or more
Short circuit
- HINT:
- If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.
- If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.
- It is not necessary to inspect the circuit when P0711 is set.
- It is not necessary to inspect the circuit when P0711 is set.
- After Stall Test;
| 1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0711) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester on.
Select the following items: "Powertrain / ECT / DTC / Current or Pending".
Read the DTCs using the intelligent tester.
- Result:
Display (DTC output)
Proceed to
Only "P0711" is output
A
"P0711" and other DTCs are output
B
- HINT:
- If any other codes besides "P0711" are output, perform troubleshooting for those DTCs first.
|
|
||||
| A | |
| 2. CHECK TRANSMISSION FLUID LEVEL |
Check the transmission fluid level (Click here).
- OK:
- Automatic transmission fluid level is correct.
|
|
||||
| OK | |
| 3. INSPECT TRANSMISSION WIRE |
Remove the TCM from the transaxle.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Specified Condition
17 (E2) - 18 (THO1)
90 Ω to 156 kΩ
17 (E2) - Body ground
10 kΩ or higher
18 (THO1) - Body ground
10 kΩ or higher
- HINT:
- If the resistance is out of the specified range with the ATF temperature shown in the table below, the driveability of the vehicle may decrease.
- Standard resistance:
ATF Temperature
Specified Condition
10°C (50°F)
5.8 to 7.1 kΩ
110°C (230°F)
0.22 to 0.28 kΩ
|
|
||||
| NG | |
| 4. CHECK ATF TEMPERATURE SENSOR |
Disconnect the ATF temperature sensor connector from the transmission wire.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Specified Condition
E2 - THO1
90 Ω to 156 kΩ
E2 - Body ground
10 kΩ or higher
THO1 - Body ground
10 kΩ or higher
- HINT:
- If the resistance is out of the specified range with the ATF temperature shown in the table below, the driveability of the vehicle may decrease.
- Standard resistance:
ATF Temperature
Specified Condition
10°C (50°F)
5.8 to 7.1 kΩ
110°C (230°F)
0.22 to 0.28 kΩ
|
|
||||
| OK | ||
| ||
