REMOVAL
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1.
PRECAUTION |
 |
- HINT:
- (Click here)
| 2.
TURN FRONT WHEELS TO FACE STRAIGHT AHEAD |
|
| 3.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
 |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
| 5.
REMOVE FRONT DOOR SCUFF PLATE LH
|
 |
- Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
| 6.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
|
 |
- Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 7.
REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
 |
- HINT:
-
Click here for 2GR-FE RHD, Click here for except 2GR-FE RHD.
| 8.
REMOVE NO. 2 LOWER STEERING WHEEL COVER
|
 |
Using a screwdriver, disengage the claw and remove the No. 2 lower steering wheel cover.


- HINT:
- Tape up the screwdriver tip before use.
| 9.
REMOVE NO. 3 LOWER STEERING WHEEL COVER
|
 |
Using a screwdriver, disengage the claw and remove the No. 3 lower steering wheel cover.


- HINT:
- Tape up the screwdriver tip before use.
| 10.
REMOVE STEERING PAD
|
 |
Using a "TORX" socket (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.


- Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.
- NOTICE:
- When removing the steering pad, do not pull the airbag wire harness.
Disconnect the horn connector from the steering pad.
Disconnect the 2 airbag connectors and remove the steering pad.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
| 11.
REMOVE STEERING WHEEL ASSEMBLY |
 |
Remove the steering wheel assembly set nut.
Put matchmarks on the steering wheel assembly and the steering main shaft.
Disconnect the connectors from the spiral cable.
- Using SST, remove the steering wheel assembly.
- SST
- 09950-50013
(09951-05010, 09952-05010, 09953-05020, 09954-05031)
| 12.
REMOVE LOWER STEERING COLUMN COVER |
 |
- Remove the 2 screws.
Disengage the 2 claws to remove the lower steering column cover.
| 13.
REMOVE UPPER STEERING COLUMN COVER |
 |
- Disengage the claw to remove the upper steering column cover.
| 14.
REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
 |
Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.
- Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.
| 15.
REMOVE NO. 1 AIR DUCT |
 |
- Disengage the 2 claws and remove the No. 1 air duct.
| 16.
SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY |
 |
- Remove the clamp from the steering column hole shield.
- Remove the bolt.
- NOTICE:
- Do not separate the steering intermediate shaft assembly from the power steering link assembly.
- Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.
Separate the steering intermediate shaft assembly from the power steering link assembly.
| 17.
REMOVE STEERING COLUMN ASSEMBLY |
 |
Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.
- Remove the bolt, 2 nuts, and the steering column assembly.
| 18.
REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY |
 |
- Put matchmarks on the steering intermediate shaft assembly and the steering column assembly.
Remove the bolt and the steering intermediate shaft assembly from the steering column assembly.