2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

Short in CAN Bus Lines

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The CAN bus wires are considered to be shorted when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short in CAN bus wires
  2. Skid control ECU
  3. Steering angle sensor
  4. Yaw rate sensor
  5. ECM
  6. Main body ECU
  7. A/C amplifier
  8. Center airbag sensor assembly
  9. Combination meter
  10. CAN No. 1 J/C
  11. CAN No. 4 J/C

WIRING DIAGRAM

C144982E04
C152829E04

INSPECTION PROCEDURE

NOTICE:
  1. Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the engine switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


1. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (DLC3 BRANCH WIRE)

  1. C133233E02
    Turn the engine switch off.

  1. Disconnect DLC3 branch wire connector E62 from the CAN No. 1 J/C "B" side (without earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. C126231E11
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-14 (CANL)
    Engine switch off
    1 MΩ or higher

  1. Reconnect DLC3 branch wire connector E62 to the CAN No. 1 J/C "B" side (without earth terminal).



NG
REPAIR OR REPLACE CAN NO. 1 BUS BRANCH WIRE OR CONNECTOR (DLC3 BRANCH WIRE)
OK


2. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (CAN NO. 1 J/C SIDE)

  1. C142742E05
    Disconnect CAN main bus wire connector E43 from the CAN No. 1 J/C "A" side (with earth terminal).

  1. C126231E11
    Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-14 (CANL)
    Engine switch off
    108 to 132 Ω



OK
Go to step 7
NG


3. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (CAN NO. 1 J/C BRANCH WIRE)

  1. C126231E11
    Reconnect CAN main bus wire connector E42 to the CAN No. 1 J/C "A" side (with earth terminal).

  1. Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.

  1. While observing the resistance value shown on the tester, disconnect connectors E44, E45, E46 and E63 from the CAN No. 1 J/C one by one until the resistance becomes normal (between 54 and 69 Ω).

    HINT:
    Disconnect the branch wire connectors other than those of the DLC3.

    C152826E01
    C152831E01
    CAN No. 1 J/C Connector ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Center Airbag Sensor Assembly (E45)
    Black
    B
    W
    CAN No. 1 J/C Connector ("B" side, without earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Yaw Rate Sensor (E46)
    Blue
    B
    W
    Steering Angle Sensor (E63)
    Brown
    B
    W
    Main Body ECU (E44)
    Black
    B
    W

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch wires.


    Result:
    Symptom
    Proceed to
    The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts in the branch wires.)
    A
    The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short in one or more of the branch wires.)
    B

  1. When there is a short in one or more of the branch wires:

    1. Reconnect all of the connectors to the CAN No. 1 J/C, except for the one that was disconnected last (the short-circuited bus wire). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in one branch wire only.

      HINT:
      1. The connectors connected to the CAN No. 1 J/C can be distinguished according to the color of the communication bus wires and the shape of the connectors.
      2. Reconnecting the connectors to non-specified positions on the CAN No. 1 J/C does not affect system operation. However, it is preferred to reconnect the connectors to their specified positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



B
Go to step 14
A


4. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (COMBINATION METER MAIN BUS WIRE)

  1. C133231E05
    Disconnect combination meter main bus wire connector E43 from the CAN No. 1 J/C "B" side (without earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. C126231E11
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-14 (CANL)
    Engine switch off
    108 to 132 Ω



OK
REPLACE CAN NO. 1 J/C
NG


5. RECONNECT CONNECTOR
  1. Reconnect combination meter main bus wire connector E43 to the CAN No. 1 J/C "B" side (without earth terminal).


NEXT


6. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (COMBINATION METER)

  1. C126231E11
    Disconnect combination meter connector F1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-14 (CANL)
    Engine switch off
    108 to 132 Ω

    HINT:
    If the resistance changes to 108 to 132 Ω when the connector is disconnected, there may be a short in the combination meter.



NG
REPAIR OR REPLACE CAN NO. 1 BUS MAIN WIRE OR CONNECTOR (COMBINATION METER MAIN BUS WIRE)
OK

REPLACE COMBINATION METER ASSEMBLY

7. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (CAN NO. 4 J/C - CAN NO. 1 J/C)
  1. Reconnect CAN No. 1 J/C connector E42.

  1. C133246E14
    Disconnect CAN No. 4 J/C connector E41.

  1. C126400E08
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-14 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN NO. 1 BUS MAIN WIRE OR CONNECTOR (CAN NO. 1 J/C - CAN NO. 4 J/C)
OK


8. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (CAN NO. 4 J/C WIRE)
  1. Reconnect CAN No. 4 J/C connector E41.

  1. C133245E11
    Disconnect CAN No. 4 J/C connector A40.

  1. C126400E08
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-14 (CANL)
    Engine switch off
    108 to 132 Ω



OK
Go to step 11
NG


9. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (A/C AMPLIFIER BRANCH WIRE)
  1. Reconnect CAN No. 4 J/C connector A40.

  1. C133246E51
    Disconnect CAN No. 4 J/C connector E41.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E41-1 (CANH) - E41-7 (CANL)
    Engine switch off
    1 MΩ or higher



NG
Go to step 10
OK

REPLACE CAN NO. 4 J/C

10. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (A/C AMPLIFIER - CAN NO. 4 J/C)

  1. C133246E20
    Disconnect A/C amplifier connector E38.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E41-1 (CANH) - E41-7 (CANL)
    Engine switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN NO. 1 BUS BRANCH WIRE OR CONNECTOR (A/C AMPLIFIER BRANCH WIRE)
OK

REPLACE A/C AMPLIFIER

11. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (ECM MAIN BUS WIRE)

  1. C133245E25
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A40-1 (CANH) - A40-7 (CANL)
    Engine switch off
    108 to 132 Ω
    A40-2 (CANH) - A40-8 (CANL)
    Engine switch off
    1 MΩ or higher

    Result:
    Result
    Defective Wire
    Proceed to
    OK
    -
    A
    NG
    ECM wire
    B
    NG
    Skid control ECU wire
    C



B
Go to step 13

C
Go to step 12
A

REPLACE CAN NO. 4 J/C

12. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (SKID CONTROL ECU - CAN NO. 4 J/C)

  1. C133245E16
    Disconnect skid control ECU connector A26.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A40-2 (CANH) - A40-8 (CANL)
    Engine switch off
    1 MΩ or higher

    HINT:
    Measure the resistance with CAN No. 4 J/C connector A40 disconnected.



OK
REPLACE SKID CONTROL ECU
NG

REPAIR OR REPLACE CAN NO. 1 BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU BRANCH WIRE)

13. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE (ECM MAIN BUS WIRE)

  1. C133245E14
    Disconnect ECM connector A55.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A40-1 (CANH) - A40-7 (CANL)
    Engine switch off
    1 MΩ or higher

    HINT:
    Measure the resistance with CAN No. 4 J/C connector A40 disconnected.



NG
REPAIR OR REPLACE CAN NO. 1 BUS MAIN WIRE OR CONNECTOR (ECM - CAN NO. 4 J/C)
OK

REPLACE ECM

14. RECONNECT CONNECTOR
  1. Reconnect the connector for the short-circuited branch wire to the CAN No. 1 J/C (the connector that caused the bus wire resistance to become normal (between 54 and 69 Ω) when it was disconnected).


NEXT


15. CHECK FOR SHORT IN CAN NO. 1 BUS WIRE

  1. C126231E11
    Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short-circuited branch wire is connected. (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-14 (CANL)
    Engine switch off
    54 to 69 Ω or higher

    HINT:
    If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



NG
REPAIR OR REPLACE CAN NO. 1 BUS BRANCH WIRE OR CONNECTOR (CORRESPONDING ECU OR SENSOR BRANCH WIRE)
OK

REPLACE CORRESPONDING ECU OR SENSOR


← Open in CAN Main Bus Line (from Jun 2009)Short in CAN Bus Lines (from Jun 2009) →