2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

Short in CAN Bus Lines

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The CAN bus wires are considered to be shorted when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short in CAN bus wires
  2. Skid control ECU
  3. Steering angle sensor
  4. Yaw rate sensor
  5. ECM
  6. Main body ECU
  7. Air conditioning amplifier
  8. Center airbag sensor assembly
  9. Combination meter
  10. Navigation receiver assembly
  11. No. 1 CAN J/C
  12. No. 4 CAN J/C

WIRING DIAGRAM

C213910E04
C225793E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any other switches, or any doors triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


1. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)

  1. C133246E24
    Turn the ignition switch off.

  1. Disconnect the DLC3 branch wire connector (E41) from the No. 4 CAN J/C (front of the vehicle).

  1. C126231E11
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-14 (CANL)
    Ignition switch off
    1 MΩ or higher

  1. Reconnect the DLC3 branch wire connector (E41) to the No. 4 CAN J/C (front of the vehicle).



NG
REPAIR OR REPLACE DLC3 BRANCH WIRE OR CONNECTOR
OK


2. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN J/C SIDE)

  1. C142742E05
    Disconnect the CAN main bus wire connector (E42) from the No. 1 CAN J/C "A" side (with earth terminal).

  1. C126231E11
    Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 7
OK


3. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN J/C BRANCH WIRE)

  1. C126231E11
    Reconnect the CAN main bus wire connector (E42) to the No. 1 CAN J/C "A" side (with earth terminal).

  1. Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.

  1. While observing the resistance value shown on the tester, disconnect connectors E44, E45, E46 and E47 from the No. 1 CAN J/C one by one until the resistance becomes normal (between 54 and 69 Ω).C212233E01
    C142744E05

    No. 1 CAN J/C Connector ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Center Airbag Sensor Assembly (E45)
    Black
    B
    W
    No. 1 CAN J/C Connector ("B" side, without earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Yaw Rate Sensor (E46)
    Blue
    B
    W
    Air Conditioning Amplifier (E47)
    Gray
    B
    W
    Navigation Receiver Assembly (E93)*
    Brown
    B
    W
    Main Body ECU (E44)
    Black
    B
    W
    *: w/ Navigation system

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch wires.


    Result:
    Symptom
    Proceed to
    The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts in the branch wires.)
    A
    The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short in one or more of the branch wires.)
    B

  1. When there is a short in one or more of the branch wires:

    1. Reconnect all of the connectors to the No. 1 CAN J/C, except for the one that was disconnected last (the short-circuited bus wire). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in one branch wire only.

      HINT:
      1. The connectors connected to the No. 1 CAN J/C can be distinguished according to the color of the communication bus wires and the shape of the connectors.
      2. Reconnecting the connectors to non-specified positions on the No. 1 CAN J/C does not affect system operation. However, it is preferred to reconnect the connectors to their specified positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



B
Go to step 14
A


4. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER MAIN BUS WIRE)

  1. C144994E01
    Disconnect the combination meter main bus wire connector (E43) from the No. 1 CAN J/C "B" side (without earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. C126231E11
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPLACE NO. 1 CAN J/C
OK


5. RECONNECT CONNECTOR
  1. Reconnect the combination meter main bus wire connector (E43) to the No. 1 CAN J/C "B" side (without earth terminal).


NEXT


6. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER)

  1. C126231E11
    Disconnect the combination meter connector (F1).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    HINT:
    If the resistance changes to 108 to 132 Ω or more when the connector is disconnected, there may be a short in the combination meter.



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE (COMBINATION METER MAIN BUS WIRE)
OK

REPLACE COMBINATION METER

7. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN J/C - NO. 4 CAN J/C)

  1. C133245E17
    Reconnect the CAN main bus wire connector (E42).

  1. Disconnect the No. 4 CAN J/C connector (A40).

  1. C126400E08
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-14 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
Go to step 11
NG


8. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR BRANCH WIRE)

  1. C133246E16
    Reconnect the No. 4 CAN J/C connector (A40).

  1. Disconnect the No. 4 CAN J/C connector (E41).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E41-3 (CANH) - E41-9 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 10
OK


9. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN J/C - NO. 4 CAN J/C)

  1. C133246E23
    Disconnect the No. 4 CAN J/C connector (E41).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E41-4 (CANH) - E41-10 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 1 CAN J/C - NO. 4 CAN J/C)
OK

REPLACE NO. 4 CAN J/C

10. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR - NO. 4 CAN J/C)

  1. C133246E16
    Disconnect the steering angle sensor connector (E17).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E41-3 (CANH) - E41-9 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE STEERING ANGLE SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE STEERING ANGLE SENSOR

11. CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN BUS WIRE)

  1. C133245E22
    Disconnect the No. 4 CAN J/C connector (A40).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-1 (CANH) - A40-7 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 13
OK


12. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU - NO. 4 CAN J/C)

  1. C133245E19
    Disconnect the skid control ECU connector (A25) or (A26).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-2 (CANH) - A40-8 (CANL)
    Ignition switch off
    1 MΩ or higher

    HINT:
    Measure the resistance with the No. 4 CAN J/C connector (A40) disconnected.



OK
REPLACE SKID CONTROL ECU
NG

REPAIR OR REPLACE SKID CONTROL ECU BRANCH WIRE OR CONNECTOR

13. CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN BUS WIRE)

  1. C133245E22
    Disconnect the ECM connector (A24).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-1 (CANH) - A40-7 (CANL)
    Ignition switch off
    1 MΩ or higher

    HINT:
    Measure the resistance with the No. 4 CAN J/C connector (A40) disconnected.



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE (ECM - NO. 4 CAN J/C)
OK

REPLACE ECM

14. RECONNECT CONNECTOR
  1. Reconnect the connector for the short-circuited branch wire to the No. 1 CAN J/C (the connector that caused the bus wire resistance to become normal (between 54 and 69 Ω) when it was disconnected).


NEXT


15. CHECK FOR SHORT IN CAN BUS WIRES

  1. C126231E11
    Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short-circuited branch wire is connected. (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-14 (CANL)
    Ignition switch off
    54 to 69 Ω

    HINT:
    If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR


← Short in CAN Bus Lines (Oct 2006 – May 2009)Short to B+ in CAN Bus Line (Oct 2006 – May 2009) →