Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM
ECM Power Source Circuit
Circuit diagnosis · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
When the ignition switch is turned on (IG), the battery voltage is applied to terminal IGSW of the ECM. The ECM MREL output signal causes a current to flow to the coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM. If the ignition switch is turned off, the ECM holds the EFI relay ON for a maximum of 2 seconds to allow for the initial setting of the throttle valve. When the ignition switch is turned on (IG), voltage from the ECM's MREL terminal is applied to the engine room junction block (EFI relay). This causes the contacts of the engine room junction block (EFI relay) to close, which supplies power to terminal +B or +B2 of the ECM. WIRING DIAGRAM
INSPECTION PROCEDURE
1. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
Standard resistance:
RHD:
Tester Connection
Specified Condition
E1 (C58-81) - Body ground
Below 1 Ω
LHD:
Tester Connection
Specified Condition
E1 (C55-81) - Body ground
Below 1 Ω
Reconnect the ECM connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
2. CHECK ENGINE ROOM JUNCTION BLOCK (EFI RELAY VOLTAGE)
Remove the engine room junction block from the engine room R/B.
Turn the ignition switch on (IG).
Measure the voltage between the terminals.
Standard voltage:
Tester Connection
Specified Condition
1E-6 - Body ground
9 to 14 V
OK
NG
3. INSPECT EFI MAIN FUSE
Remove the EFI MAIN fuse from the engine room R/B.
Measure the EFI MAIN fuse resistance.
Standard resistance:
Below 1 Ω
Reinstall the EFI MAIN fuse.
NG
OK
4. CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK - BATTERY)
Disconnect the negative battery terminal.
Disconnect the positive battery terminal.
Remove the engine room junction block from the engine room R/B.
Measure the resistance between the terminals.
Standard resistance:
Check for open:
Tester Connection
Specified Condition
1G-1 - Positive battery terminal
Below 1 Ω
Check for short:
Tester Connection
Specified Condition
1G-1 or Positive battery terminal - Body ground
10 kΩ or higher
Reinstall the engine room junction block.
Reconnect the positive battery terminal.
Reconnect the negative battery terminal.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here )
5. INSPECT ENGINE ROOM JUNCTION BLOCK (EFI RELAY)
Remove the engine room junction block from the engine room R/B.
Measure the resistance between the terminals.
Standard resistance:
Tester Connection
Specified Condition
1E-6 - 1E-12
10 kΩ or higher
1E-6 - 1E-12
Below 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-11)
Reinstall the engine room junction block.
NG
REPLACE ENGINE ROOM JUNCTION BLOCK
OK
6. INSPECT EFI NO. 2 FUSE
Remove the EFI No. 2 fuse from the engine room R/B.
Measure the EFI No. 2 fuse resistance.
Standard resistance:
Below 1 Ω
Reinstall the EFI No. 2 fuse.
NG
OK
7. CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM JUNCTION BLOCK)
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Remove the engine room junction block from the engine room R/B.
Measure the resistance between the terminals.
Standard resistance (Check for open):
RHD:
Tester Connection
Specified Condition
1E-6 - +B (A24-2)
Below 1 Ω
1E-6 - +B2 (A24-1)
Below 1 Ω
LHD:
Tester Connection
Specified Condition
1E-6 - +B (A55-2)
Below 1 Ω
1E-6 - +B2 (A55-1)
Below 1 Ω
Standard resistance (Check for open):
RHD:
Tester Connection
Specified Condition
1E-6 or +B (A24-2) - Body ground
10 kΩ or higher
1E-6 or +B2 (A24-1) - Body ground
10 kΩ or higher
LHD:
Tester Connection
Specified Condition
1E-6 or +B (A55-2) - Body ground
10 kΩ or higher
1E-6 or +B2 (A55-1) - Body ground
10 kΩ or higher
Reinstall the engine room junction block.
Reconnect the ECM connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
8. INSPECT ECM (IGSW VOLTAGE)
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Measure the voltage between the terminals.
Standard voltage:
RHD:
Tester Connection
Specified Condition
IGSW (A24-28) - Body ground
9 to 14 V
LHD:
Tester Connection
Specified Condition
IGSW (A55-28) - Body ground
9 to 14 V
Reconnect the ECM connector.
OK
NG
9. INSPECT IGNITION RELAY NO. 2
Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω (Apply battery voltage between terminals 1 and 2)
Reinstall the IG2 relay.
NG
REPLACE IGNITION RELAY NO. 2
OK
10. CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)
Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
Standard resistance:
Tester Connection
Specified Condition
IG2 relay terminal 2 - Body ground
Below 1 Ω
Reinstall the IG2 relay.
Result:
Result
Proceed to
OK (without smart entry and start system)
A
OK (with smart entry and start system)
B
NG
C
B
GO TO SMART ENTRY AND START SYSTEM
C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A
11. INSPECT IGNITION SWITCH ASSEMBLY
Disconnect the E23 ignition switch connector.
Measure the resistance between the terminals.
Standard resistance:
Tester Connection
Ignition Switch Position
Specified Condition
All terminals
LOCK
10 kΩ or higher
2 - 4
ACC
Below 1 Ω
1 - 2 - 4, 5 - 6
ON
1 - 3 - 4, 5 - 6 - 7
START
Reconnect the ignition switch connector.
NG
REPLACE IGNITION SWITCH ASSEMBLY
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BATTERY)
12. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Measure the resistance between the terminals.
Standard resistance:
RHD:
Tester Connection
Specified Condition
MREL (A24-44) - Body ground
Below 1 Ω
LHD:
Tester Connection
Specified Condition
MREL (A55-44) - Body ground
Below 1 Ω
Reconnect the ECM connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK