Rear Sunshade does not Operate with Rear Sunshade Switch
Circuit diagnosis · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
SYSTEM DESCRIPTION
When the rear sunshade switch is pressed, a signal is sent directly to the rear sunshade relay.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT FUSE (GAUGE NO. 1) |
 |
Remove the GAUGE No. 1 fuse from the instrument panel J/B.
Measure the resistance of the fuse.
- Standard resistance:
- Below 1 Ω
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 2. INSPECT REAR SUNSHADE SWITCH ASSEMBLY |
 |
- Disconnect the E74 connector.
Measure the resistance between the terminals according to the value(s) in the table below.
- Standard resistance:
Tester connection
|
Condition
|
Specified condition
|
E74-1 - E74-4 (*1) E74- 3 - E74-4 (*2)
|
Rear sunshade switch is pressed
|
Below 1 Ω
|
E74-1 - E74-4 (*1) E74-3 - E74-4 (*2)
|
Rear sunshade switch is not pressed
|
10 kΩ or higher
|
*1: except RHD with the 2GR-FE*2: RHD with the 2GR-FE
|
NG |
 |
|
| REPLACE REAR SUNSHADE SWITCH |
|
|
| OK |
|
 |
|
| 3. CHECK WIRE HARNESS AND CONNECTOR (REAR SUNSHADE SWITCH - REAR SUNSHADE RELAY AND BODY GROUND) |
 |
- Disconnect the E74 and N41 connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester connection
|
Specified condition
|
E74-4 - SW (N41-5)
|
Below 1 Ω
|
E74-1 - Body ground (*1) E74-3 - Body ground (*2)
|
Below 1 Ω
|
E (N41-7) - Body ground
|
Below 1 Ω
|
SW (N41-5) - Body ground
|
10 kΩ or higher
|
*1: except RHD with the 2GR-FE*2: RHD with the 2GR-FE
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 4. INSPECT REAR SUNSHADE MOTOR |
 |
Disconnect the N42 connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester connection
|
Specified condition
|
N42-1 - N42-2
|
Below 1 Ω
|
N42-1 - Body ground
|
10 kΩ or higher
|
|
NG |
 |
|
| REPLACE REAR SUNSHADE MOTOR |
|
|
| OK |
|
 |
|
| 5. CHECK WIRE HARNESS AND CONNECTOR (REAR SUNSHADE MOTOR - REAR SUNSHADE RELAY) |
 |
- Disconnect the N42 and N41 connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester connection
|
Specified condition
|
N42-1 - MOP (N41-9)
|
Below 1 Ω
|
N42-2 - MCL (N41-10)
|
Below 1 Ω
|
MOP (N41-9) - Body ground
|
10 kΩ or higher
|
MCL (N41-10) - Body ground
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| REPLACE REAR SUNSHADE RELAY |
|