2006-2011 Camry Aurion · Service Manual HEATER & AIR CONDITIONING SYSTEM

Air Conditioning Compressor Magnetic Clutch Circuit

Circuit diagnosis · Vehicles built from Oct 2006

DESCRIPTION

When the A/C amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the A/C amplifier. Then, the MGC relay turns on to operate the magnetic clutch.

WIRING DIAGRAM

E124490E04

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    Result:
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM
A


2. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Turn the A/C switch on and off.

  1. Select the item below in the Data List, and read the display on the intelligent tester.

    Data List / Engine: 
    Tester Display
    Measure Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    (A/C Signal)
    A/C signal / ON or OFF
    ON: A/C ON
    OFF: A/C OFF
    -

    OK:
    The display is as specified in the normal condition column.



NG
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
OK


3. INSPECT FUSE (A/C NO. 2)

  1. E124481E02
    Remove the A/C No. 2 fuse from the instrument panel J/B.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Tester Item
    Condition
    Specified Condition
    A/C No. 2 fuse
    Always
    Below 1 Ω

  1. Reconnect the A/C No. 2 fuse to the instrument panel J/B.



NG
REPLACE FUSE (A/C NO. 2)
OK


4. INSPECT RELAY (MGC)

  1. B060778E04
    Remove the MGC relay from the engine room R/B and J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)

  1. Install the MGC relay to the engine room R/B and J/B.



NG
REPLACE RELAY (MGC)
OK


5. CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - BATTERY)

  1. E124470E13
    Disconnect the connector from the A/C amplifier.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    E38-20 (MGC) - Body ground
    Ignition switch off
    Below 1 V
    E38-20 (MGC) - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (A/C AMPLIFIER - BATTERY)
OK


6. INSPECT AIR CONDITIONING AMPLIFIER

  1. E124471E11
    Reconnect the connector to the A/C amplifier.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    E38-20 (MGC) - Body ground
    Ignition switch on (IG)
    A/C switch: OFF
    10 to 14 V
    E38-20 (MGC) - Body ground
    Ignition switch on (IG)
    A/C switch: ON
    Below 1 V



NG
REPLACE AIR CONDITIONING AMPLIFIER
OK


7. INSPECT A/C COMPRESSOR

  1. E005280E15
    Disconnect the connector from the A/C compressor.

  1. E124482E01
    Disconnect the connector from the magnetic clutch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    C53-3 (MG+) - A-1
    Always
    Below 1 Ω
    C53-3 (MG+) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE A/C COMPRESSOR
OK


8. INSPECT MAGNETIC CLUTCH

  1. E113611E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A-1 - Body ground
    20 °C (68°F)
    3.8 to 4.2 Ω

  1. When connector terminal A1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch's operating sound can be heard, and 2) the magnetic clutch's hub and rotor lock.



NG
REPLACE MAGNETIC CLUTCH
OK


9. CHECK HARNESS AND CONNECTOR (ENGINE ROOM R/B AND J/B - BATTERY)

  1. E124483E05
    Remove the MGC relay from the engine room R/B and J/B.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    Relay block MGC relay terminal 5 - Body ground
    10 to 14 V
    Relay block MGC relay terminal 1 - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM R/B AND J/B - A/C COMPRESSOR)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR


← Heater Control Panel Power Source Circuit (from Jun 2009)Steering Pad Switch Circuit (Oct 2006 – May 2009) →