2006-2011 Camry Aurion · Service Manual ENGINE

B2284 Brake Signal Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

DESCRIPTION

This DTC is output when: 1) the brake signal circuit between the main body ECU (instrument panel junction block assembly) and the stop light switch is malfunctioning; and 2) the CAN information is inconsistent.
DTC No.
DTC Detection Condition
Trouble Area
B2284
The brake signal circuit between the main body ECU (instrument panel junction block assembly) and the stop light switch is malfunctioning and the CAN information is inconsistent
  1. Stop light switch
  2. CAN communication system
  3. ECM
  4. Main body ECU (instrument panel junction block assembly)
  5. Wire harness or connector

WIRING DIAGRAM

B232509E02

INSPECTION PROCEDURE

HINT:
When the main body ECU (instrument panel junction block assembly) is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU (instrument panel junction block assembly) is replaced, perform the registration procedures for the engine immobiliser system.


EMERGENCY ENGINE START CONTROL
  1. If there is a malfunction in the stop light switch or STOP fuse, their signals may not be correctly transmitted to the main body ECU (instrument panel junction block assembly). This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P position.
    To activate the starter:

    1. Turn the engine switch from off to on (ACC).

    2. Press and hold the engine switch for 15 seconds.

HINT:
Before performing the inspection, depress the brake pedal and check that the stop lights come on. If the stop lights do not come on when the brake pedal is depressed, refer to the page shown in the brackets (Click here).


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch/ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    OK:
    ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen.



NG
Go to step 4
OK


2. CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)
  1. Clear the DTCs (Click here).

  1. Check for CAN communication system DTCs (Click here).

    HINT:
    If the DTCs for the CAN communication system malfunction are output, inspect those DTCs first (Click here).

    OK:
    DTC is not output.



NG
GO TO CAN COMMUNICATION SYSTEM (Click here)
OK


3. CHECK DTC OUTPUT (ENGINE CONTROL SYSTEM)
  1. Clear the DTCs (Click here).

  1. Check for DTC P0500 (Vehicle speed sensor A).

    OK:
    DTC is not output.



NG
GO TO ENGINE CONTROL SYSTEM (Click here)
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

4. CHECK HARNESS AND CONNECTOR (STOP FUSE - STOP LIGHT SWITCH)
  1. Disconnect the A79 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A79-2 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT STOP LIGHT SWITCH

  1. C205985E10
    Remove the switch.

  1. Measure the resistance of the switch.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    3 - 4
    Switch pin free
    10 kΩ or higher
    1 - 2
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin pushed in
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - MAIN BODY ECU)
  1. Disconnect IL connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A79-1 - IL-7
    Always
    Below 1 Ω
    A79-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


← B2282 Vehicle Speed Signal Malfunction (+ B2283) (from Jun 2009)B2285 Steering Lock Position Signal Circuit Malfunction (from Jun 2009) →