2006-2011 Camry Aurion · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL VVT SENSOR (for Bank 2 Exhaust side)

  1. A135699
    Install the VVT sensor with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the VVT sensor connector.


2. INSTALL VVT SENSOR (for Bank 2 Intake side)

  1. A135700
    Install the VVT sensor with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the VVT sensor connector.


3. INSTALL VVT SENSOR (for Bank 1 Exhaust side)

  1. A135702
    Install the VVT sensor with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the VVT sensor connector.


4. INSTALL VVT SENSOR (for Bank 1 Intake side)

  1. A135701
    Install the VVT sensor with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the VVT sensor connector.


5. INSTALL INTAKE AIR SURGE TANK ASSEMBLY

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
Surge Tank and Intake Manifold
No. 1 Surge Tank Stay and Surge Tank
Throttle Body Bracket and Surge Tank

  1. A129468E03
    Install a new gasket to the intake air surge tank.

  1. Using a 5 mm hexagon socket wrench, install the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the intake air surge tank with the 2 nuts and 2 bolts.

    Torque:
    Nut:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }
    Bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A129467
    Connect the connector.

  1. A129466
    Install the vacuum hose clamp with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. A129465E06
    Connect the union to check valve hose.

  1. Connect the No. 1 ventilation hose.

  1. A129464E02
    Install the clamp and connect the throttle with motor body assembly connector.

  1. Connect the vapor feed hose.

  1. Connect the 2 water by-pass hoses to the throttle with motor body assembly.


6. INSTALL NO. 1 AIR CLEANER INLET

  1. A132970
    Install the No. 1 air cleaner inlet with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


7. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  1. A132971
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the vacuum hose and hose clamp.


8. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A135706
    Install the air cleaner cap sub-assembly, and connect the 3 bands.

  1. A135705E01
    Connect the mass air flow meter connector (*1).

  1. Connect the No. 2 ventilation hose (*2).

  1. Connect the hose band (*3).

  1. A135704
    Connect the 3 vacuum hoses.


9. INSTALL AIR CLEANER INLET ASSEMBLY

  1. A132969
    Install the air cleaner inlet with the clamp and 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


10. INSTALL V-BANK COVER SUB-ASSEMBLY

  1. A140800
    Fit the 3 retainers and install the V-bank cover.


11. INSTALL COOL AIR INTAKE DUCT SEAL

  1. A141576E01
    Install the intake duct seal with the 7 clips.


12. INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY

  1. A136272
    Install the cowl top panel outer sub-assembly with the 4 bolts and 4 nuts.

    Torque:
    Bolt:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Nut:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }


13. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E135590E01
    Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration.

  1. E135589
    Connect the connector.


14. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

  1. E135588
    Engage the 4 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.


15. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

  1. E140957
    Engage the 3 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.


16. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

  1. E128810
    Engage the claw and install the front fender to cowl side seal RH.


17. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

  1. E128809
    Engage the claw and install the front fender to cowl side seal LH.


18. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. E112237E01
    Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E128820E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    37 to 52 mm (1.46 to 2.05 in.)


19. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. E112237E01
    Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E128821E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    23 to 38 mm (0.90 to 1.49 in.)

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


20. ADD ENGINE COOLANT
  1. Close the radiator drain cock plug and 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    9.0 liters (9.5 US qts, 7.9 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


21. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch OFF.

  1. A133894
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


22. INSTALL ENGINE UNDER COVER RH

23. INSTALL ENGINE UNDER COVER LH
← INSTALLATION (Oct 2006 – May 2009)COMPONENTS (from Oct 2006) →