2006-2011 Camry Aurion · Service Manual ENGINE

DATA LIST / ACTIVE TEST

System information · Vehicles built from Jun 2009


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Turn the engine switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the intelligent tester on.

  5. Enter the following menus: Body / Main Body / Data List.

  6. Read the Data List according to the display on the intelligent tester.

    HINT:
    When using intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the intelligent tester and vehicle starts.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Engine switch on (ACC) / ON or OFF
    ON: Engine switch on (ACC)
    OFF: Engine switch off
    -
    IG SW
    Engine switch on (IG) / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Starter Switch1
    Start switch 1 / ON or OFF
    ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    -
    Starter Switch2
    Start switch 2 / ON or OFF
    ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    -
    Steering Unlock Switch
    Steering lock condition / ON or OFF
    ON: Steering is unlocked (Engine switch on (ACC))
    OFF: Steering is locked (Engine switch off)
    -
    Neutral SW / Clutch SW
    Neutral start switch / ON or OFF
    ON: Shift position is P or N
    OFF: Shift position is neither P nor N
    -
    Shift P Signal
    Shift P position signal / ON or OFF
    ON: Shift position is P
    OFF: Shift position is not P
    -
    Vehicle Speed Signal
    Vehicle speed signal / STOP or RUN
    STOP: Vehicle is stopped
    RUN: Vehicle is running
    -
    Engine Condition
    Engine condition / STOP or RUN
    STOP: Engine is stopped
    RUN: Engine is running
    -
    IG1 Relay Monitor (Outside)
    IG1 relay monitor (outer) / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    IG2 Relay Monitor (Outside)
    IG2 relay monitor (outer) / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    IG1 Relay Monitor (Inside)
    IG1 relay monitor (inner) / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    IG2 Relay Monitor (Inside)
    IG2 relay monitor (inner) / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    ACC Relay Monitor
    ACC relay monitor / ON or OFF
    ON: Engine switch on (ACC)
    OFF: Engine switch off
    -
    Latch Circuit
    Latch circuit / ON or OFF
    ON: Engine switch on (IG) or engine running
    OFF: Engine switch off or on (ACC)
    -
    Starter Request Signal
    Starter request signal monitor / ON or OFF
    ON: ST relay is ON
    OFF: ST relay is OFF
    Engine switch pressed and held with shift lever in P or N
    ACC Relay Cut Signal
    ACC relay cut signal / ON or OFF
    ON: Engine is cranking
    OFF: Engine is not cranking
    -
    Starter Relay Monitor
    STARTER relay monitor / ON or OFF
    ON: Engine is cranking
    OFF: Engine is not cranking
    Engine is cranking with engine switch on (IG) and shift lever in P or N
    Power Supply Condition
    Power supply condition / ALL, ACC ON, IG1 IG2, ST ON
    ALL: All relays are OFF
    ACC ON: ACC relay is ON
    IG1: IG1 relay is ON
    IG2: IG2 relay is ON
    ST ON: ST request signal is ON
    -
    Comm Entry&Start
    Communication for certification ECU / OK or STOP
    OK: Communication
    STOP: No communication
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Turn the engine switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the intelligent tester on.

  5. Enter the following menus: Body / Main Body / Active Test.

  6. According to the display on tester, perform the Active Test.

Main Body: 
Tester Display
Test Part
Control Range
Diagnostic Note
Indicator for Lighting
Indicator for lighting
ON / OFF
-
Indicator Condition
Engine switch indicator
Green / Red / No Sig
-
P Supply for Steering Lock
Power supply for steering lock ECU (steering lock actuator assembly)
ON / OFF
-
← DTC CHECK / CLEAR (from Jun 2009)DIAGNOSTIC TROUBLE CODE CHART (from Jun 2009) →