2006-2011 Camry Aurion · Service Manual BRAKE

C1246/46 Master Cylinder Pressure Sensor Malfunction

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.
C106656E03
DTC No.
DTC Detection Condition
Trouble Area
C1246/46
When any of the following is detected:
  1. The voltage of the sensor signal is out of range (less than 0.3 V, more than 4.86 V).
  2. The sensor supply voltage is out of range (above 5.3 V, below 4.7 V).
  3. The sensor signal offset value is out of range.
  4. The sum of signal 1 and signal 2 is out of range (above 5.5 V, below 4.5 V).
  1. Master cylinder pressure sensor
  2. Master cylinder pressure sensor circuit
  3. Stop light switch circuit
  4. Brake actuator assembly (skid control ECU)

INSPECTION PROCEDURE

HINT:
Check the condition of each related circuit connector before troubleshooting (Click here).


1. CHECK STOP LIGHT OPERATION
  1. Check that the stop light comes on when the brake pedal is depressed, and goes off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF



NG
INSPECT STOP LIGHT CIRCUIT
OK


2. READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER PRESSURE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the "Data List" mode on the intelligent tester (Click here).

    Data List: ABS/TRC/VSC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Master Cylinder Sensor
    Master cylinder pressure sensor 1 reading / Min.: 0 V, Max.: 5 V
    When brake pedal is released: 0.3 to 0.5 V
    -

  1. Check that the hydraulic pressure value of the master cylinder pressure sensor observed on the intelligent tester changes when the brake pedal is depressed.

    OK:
    When the pedal is depressed, voltage displayed on the intelligent tester increases.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Select the "Data List" mode on the intelligent tester (Click here).

    Data List: ABS/TRC/VSC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Lamp SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light condition observed on the intelligent tester changes when the brake pedal is depressed.

    OK:
    When the brake pedal is depressed, the intelligent tester displays "ON".



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. At a speed of 30 km/h (18 mph) or more, drive the vehicle and perform braking test (decelerate the vehicle by depressing the brake pedal).

  1. Check if the same DTC is recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Result
    Proceed to
    DTC (C1246/46) is not output
    A
    DTC (C1246/46) is output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)


← C1246/46 Master Cylinder Pressure Sensor Malfunction (Jun 2006 – Sep 2006)C1246/46 Master Cylinder Pressure Sensor Malfunction (from Jun 2009) →