2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

CAUTION:
If using a pacemaker, be sure to read the manual of the pacemaker before using the electrical key because the radio waves of the electrical key may affect the pacemaker.


SMART ENTRY AND START SYSTEM DESCRIPTION
  1. In addition to conventional mechanical key and wireless door lock control functions, the smart entry and start system enables door locking/unlocking, steering lock releasing, engine starting, and luggage compartment door opening without operating the electrical key. The only requirement is that the electrical key is in the user's possession.

    1. This system is controlled by the certification ECU. When the certification ECU detects the presence of an electrical key in one of the detection areas, it identifies and checks the ID code, and outputs operation signals to the related ECU in accordance with their functions.
    2. The detection areas are formed by 6 oscillators (2 door oscillators, 2 luggage compartment oscillators, and 2 cabin oscillators).


DETECTION AREA
B150887E04
  1. Precautions for the entire system:

    1. Be sure to carry the electrical key during inspection of the smart entry and start system.
    2. As weak radio waves are used to detect the electrical key, the electrical key detection area may decrease, or the electrical key may not be detected correctly in the following situations:
      1. The electrical key battery is depleted.
      2. Any facilities that generate strong radio waves, such as a TV tower, power plant, broadcast station, or gas station, are located near the inspection site.
      3. A wireless device, such as a cellular phone, is carried with the electrical key.
      4. The electrical key is in contact with or covered with metal.
      5. Another wireless door lock control function is operated near the vehicle.
      6. The electrical key is located near a device that generates high voltage or noise.
    1. The electrical key may be difficult to operate for a reason relating to the vehicle body shape.
    2. The electrical key may not be detected correctly if it is around the vehicle's windows, the door handle, or the center of the bumper even when it is in the detection area outside the vehicle.
    3. The electrical key may not be detected correctly if it is on the instrument panel, rear package tray, floor, or in the glove box even when it is in the detection area inside the vehicle.
    4. The engine cannot be started even when the electrical key is in the detection area inside the luggage compartment.
    5. The electrical key may not operate if the electrical key is not held properly.
    6. The smart entry and start system does not operate in the following conditions:
      1. The smart entry and start system is canceled.
      2. The electrical key battery is completely depleted (the indicator does not blink when pushing any of the buttons on the electrical key).


FUNCTION OF MAIN COMPONENTS
*: w/ Electrical Key Antenna
Component
Function
Electrical Key
Consists of mechanical key, transmitter for wireless door lock control, and transceiver for smart entry and start system
Certification ECU
Controls smart entry and start system in accordance with signals from each oscillator, various switches, ECUs, and electrical key
  1. Judges and certifies ID code from door control receiver
  2. Transmits engine immobiliser unset signal to ID code box
  3. Transmits steering unlock signals to steering lock ECU
Main Body ECU (Instrument Panel J/B)
Controls push button start function in accordance with signals from various switches, ECUs, and combination meter
  1. Transmits electrical key verification request signal to certification ECU in accordance with engine switch signal, and turns relays ON and OFF
  2. Receives request signal from certification ECU and actuates door lock motor to unlock or lock door
  3. Transmits each door condition signal to certification ECU
ID Code Box
Receives steering unlock or engine immobiliser unset signals from certification ECU, certifies them, and transmits unset signals to steering lock ECU or ECM
Outside Door Handle (driver door) (antenna)
Transmits request signals
Outside Door Handle (driver door) (touch sensor)
Detects that person touches inside of outside handle
Outside Door Handle (driver door) (lock switch)
Transmits door lock request signals to certification ECU
Door Electrical Key Oscillator
Receives request signal from certification ECU, and forms detection area around front door
Indoor Electrical Key Oscillator (console and rear seat)
Receives request signal from certification ECU, and forms detection area in vehicle interior
Luggage Compartment Electrical Key Oscillator (inner)
Receives request signal from certification ECU, and forms detection area in luggage compartment
Luggage Compartment Electrical Key Oscillator (outer)
Receives request signal from certification ECU, and forms detection area around luggage compartment door
Door Control Receiver
  1. Receives ID code from electrical key in detection area and transmits it to certification ECU
  2. Receives ID code from electrical key in luggage compartment and transmits it to certification ECU
Electrical Key Antenna*
Receives ID code from electrical key and transmits it to door control receiver
Luggage Compartment Door Opener Outer Switch
Transmits luggage compartment door open request signal to certification ECU
Stop Light Switch
Outputs state of brake pedal to main body ECU
  1. Wireless Door Lock Buzzer
  2. Combination Meter
    1. Multi-information Display
    2. Buzzer
When certification ECU detects human errors such as those below, it warns driver by sounding wireless door lock buzzer, displaying information and sounding buzzer in combination meter in accordance with request signal from ECU
Example:
  1. Electrical key is taken out of vehicle
  2. Driver leaves vehicle while engine is still running
  3. Driver leaves vehicle while shift lever is in any position other than P

CONSTRUCTION AND OPERATION

  1. Electrical Key
    The electrical key consists of a mechanical key, a transmitter for the wireless door lock control, and a transceiver for the smart entry and start system.

    1. The transceiver for the smart entry and start system receives signals from the oscillators and sends the ID code to the tuner.
    2. The transmitter for the wireless door lock control has a LOCK switch, UNLOCK switch, LUGGAGE COMPARTMENT switch, and PANIC switch.
    3. This mechanical key works for the driver door, luggage compartment door, and glove box, but cannot start the engine.
    A total of 7 electrical keys can be registered.
    B137961E01

  2. Oscillator (door oscillator, front and rear indoor oscillator, luggage compartment inner oscillator, luggage compartment outer oscillator)
    Each oscillator transmits the request signal received from the certification ECU, and forms an electrical key detection area to detect the presence of an electrical key. The detection area formed by the front door oscillator and luggage compartment outer oscillator is approximately 0.7 to 1.0 m (2.3 to 3.3 ft) from the outside handle of the door or the center of the rear bumper.

    1. The detection area of the front door oscillator is formed by transmitting a request signal every 0.25 seconds while the engine switch is off and each door is locked. In this way, it detects the proximity of an electrical key. During entry lock, the detection area is formed with the lock switch on.
    2. The detection area of the luggage compartment outer oscillator is formed when the power luggage door open switch is on.
    3. The detection area of the indoor oscillator (front and rear) is formed when the driver door is opened or closed, during start ignition, when a warning is activated, or when the lock switch is on.
    4. The detection area of the luggage compartment inner oscillator is formed when the luggage compartment door is closed, or when the luggage compartment opener outer switch or lock switch is pressed.


ENTRY FUNCTION OPERATION
  1. The smart entry and start system has the following functions:

    Function
    Outline
    Mechanical Key
    Operation is same as conventional mechanical key.
    Wireless Door Lock Control
    This function remotely locks and unlocks all doors or luggage compartment. Operation is same as wireless door lock control system. However, receiver in certification ECU uses entry door control receiver to control locking and unlocking.
    Entry Illumination
    When person carrying electrical key enters detection area, door will enter unlock standby mode and front map light and foot light will illuminate.
    Entry Unlock
    When electrical key is located in detection area of door oscillator, door will unlock by touching inside of outside door handle.
    Entry Lock
    When electrical key is located in detection area of door oscillator and engine switch is off, door can be locked by pressing lock switch on outside door handle.
    Entry Luggage Compartment Open
    When electrical key is in detection area of luggage compartment outer oscillator, luggage compartment opens by pressing luggage compartment opener outer switch.
    Window Close
    With the electrical key in the action area of door oscillator, all open windows are closed when the lock switch on the door outside handle is pressed for 3 seconds or more.
    Memory Call
    This function operates driving position memory system in accordance with electrical key ID code.
    Electrical Key Lock-in Prevention
    1. Prevents confinement of electrical key if door is locked using outside door handle while electrical key is still inside vehicle.
    2. If all doors are locked and luggage compartment door is closed while electrical key is still in luggage compartment, warning buzzer sounds. If luggage compartment opener outer switch is operated, luggage compartment door can be opened.
    Warning
    When any of situations below occur, smart entry and start system causes certification ECU to sound buzzer in combination meter and wireless door lock buzzer, and display information in order to alert driver.
    1. Exit warning if shift lever position is not P and power source mode is not off.
    2. Exit warning if shift lever position is P and power source mode is not off.
    3. Warning if occupant leaves with electrical key.
    4. Warning if engine switch is operated while electrical key is outside actuation area.
    5. Warning if entry lock is operated while electrical key is inside vehicle.
    6. Warning if electrical key battery is weak.
    7. The electrical key is left in the vehicle.
    8. A door is ajar.
    9. The electrical key is left in the luggage compartment.
    10. Steering lock does not release.
    11. The steering lock mechanism is malfunctioning.
    12. The main body ECU is malfunctioning.
    13. An engine start method is displayed.
    Battery Saving
    If electrical key is constantly located within actuation area of door oscillator, system maintains periodic communication with electrical key. Therefore, if vehicle remains parked in that state for a long time, electrical key battery and vehicle battery could be drained.
    Key Cancel (Click here)
    Following electrical key functions can be cancelled by performing certain operations:
    1. Entry Unlock/Lock
    2. Memory Call
    3. Entry Luggage Compartment Open
    4. Electrical key Lock-in Prevention
    5. Warning
    Electrical Key Code Registration
    The total number of electrical keys that can be registered is seven.
    Enables the registration (writing and storing) of transmitter recognition codes in the EEPROM that is contained in the certification ECU.


WIRELESS DOOR LOCK AND UNLOCK AND LUGGAGE COMPARTMENT OPEN FUNCTION
Push the LOCK/UNLOCK/PANIC/LUGGAGE COMPARTMENT switch on the electrical key to operate each function. For details, (Click here).

ENTRY UNLOCK FUNCTION
  1. The detection area is formed by communication between a door oscillator and door control receiver when the door is locked in order to detect access of the person carrying the electrical key.

  2. When the person carrying the electrical key enters the detection area around the vehicle, the matching of the ID codes for a door oscillator and electrical key will automatically be performed. After the matching is completed, the door will enter unlock standby mode.

  3. In unlock standby mode, the antenna built into the outside handle starts sensing. If the outside handle is held (the back side of the handle is touched), the door unlock operation will be performed. At this time, the hazard warning light blinks twice and the wireless door lock buzzer sounds twice.

  4. If any of the doors are not opened after a door unlock operation, all doors will automatically lock after 30 seconds.


ENTRY LOCK FUNCTION
  1. After leaving the vehicle carrying the electrical key, push the lock switch on the outside handle when all the doors are closed.

  2. The certification ECU determines whether the electrical key is located inside or outside the cabin based on the information from a door oscillator and room oscillator. Then matching of the ID codes is performed.

  3. When the matching result shows that the ID codes of the electrical key and indoor antenna do not match and the ID codes of the electrical key and door oscillator match, the door lock function will operate. At this time, the hazard warning lights blink once and the wireless door lock buzzer sounds once.

  4. If the electrical key is located inside the cabin, the door lock function will not operate and the alarm buzzer (beep sound) will sound for 2 seconds.


ENTRY LUGGAGE COMPARTMENT OPEN FUNCTION
Stand in front of the luggage compartment with the electrical key and push the power luggage compartment door opener outer switch to start the matching of the ID codes for the electrical key oscillator (outside luggage compartment). If the ID codes match, luggage compartment door open operation will be performed.

ELECTRICAL KEY LOCK-IN PREVENTION FUNCTION
  1. If you attempt to lock the door through keyless operation (move the lock knob to the lock position and then close the door) with the electrical key in the cabin, the system determines that the electrical key is located in the cabin and unlocks the door.

  2. If the luggage compartment is closed with the electrical key in it, the alarm will sound and the luggage compartment can be opened only when all the doors are locked in order to prevent electrical key confinement in the vehicle.


ENTRY ILLUMINATION FUNCTION
When a person carrying the electrical key enters the detection area, the door will enter unlock standby mode and the front map light will illuminate.

HINT:
The entry illumination function operates when the electrical key enters the vehicle exterior detection area from out of the detection area. If the electrical key remains in the detection area for 3 seconds or more, the illumination function does not operate.


MEMORY CALL FUNCTION
When the engine switch is off and the driver side door is closed, opening the door will operate the memory call function (the door will move to a previously recorded driving position). Using the electrical key, memory call, electrical key registration and electrical key cancellation can be performed.

WARNING FUNCTION
  1. General
    When any of the situations below occur, the smart entry and start system causes the certification ECU to sound the buzzer in the combination meter and the wireless door lock buzzer, and illuminate the combination meter's multi-information display in order to alert the driver.

    Warning Function Operation Condition
    Situation
    Exit warning if shift lever position is not P and power source mode is not off.
    A
    Exit warning if shift lever position is P and power source mode is not off.
    B
    Warning if occupant leaves with electrical key.
    C
    Warning if engine switch is operated while electrical key is outside detection area.
    D
    Warning if entry lock is operated while electrical key is inside cabin.
    E
    Warning if electrical key battery is weak.
    F
    The electrical key is left in the vehicle.
    G
    A door is ajar.
    H
    The electrical key is left in the luggage compartment.
    I
    Steering lock does not release.
    J
    The steering lock mechanism is malfunctioning.
    K
    The main body ECU (instrument panel J/B) is malfunctioning.
    L
    An engine start method is displayed.
    M

  2. Situation A
    There are 2 patterns for situation A.
    Pattern 1: In situation A, the door is opened and the user tries to leave the vehicle.
    Pattern 2: Then the user holds the electrical key and tries to move away from the vehicle.
    In these situations, the following control is performed:

    1. Pattern 1
      Possible Effects without Warning
      Sudden vehicle start, vehicle theft, vehicle roll-away
      Warning Condition
      The certification ECU gives warning when all following conditions are satisfied:
      1. The shift lever position is not P.
      2. The engine switch is not off.
      3. The driver side door is opened.
      4. Vehicle speed is less than 5 km/h (3.1 mph).
      Combination Meter
      1. Buzzer
      Warning:
      Continuous sound
      Combination Meter
      1. Multi-information Display
      Warning:
      Information below is displayed on the combination meter:
      1. "Shift to P Range"
      "Shift to P Range" warning is stopped when one of the following conditions is met:
      1. The engine switch is off.
      2. Vehicle speed is above 0 km/h (0 mph).
      3. The shift lever position is P.
      Wireless Door Lock Buzzer
      -
      Warning Stop Condition
      The warning is stopped when one of the following conditions is met:
      1. The engine switch is off.
      2. The shift lever position is P.
      3. The driver side door is closed.
      4. Vehicle speed is above 5 km/h (3.1 mph).
    1. Pattern 2
      Possible Effects without Warning
      Sudden vehicle start, vehicle theft, vehicle roll-away
      Warning Condition
      The certification ECU gives warning when all following conditions are satisfied:
      1. The shift lever position is not P.
      2. The engine switch is not off.
      3. The driver side door is opened and closed.
      4. Vehicle speed is 0 km/h (0 mph).
      5. The electrical key is not in the cabin or luggage compartment.
      Combination Meter
      1. Buzzer
      Warning:
      Continuous sound
      The warning is stopped when one of the following conditions is met:
      1. The engine switch is off.
      2. The shift lever position is P.
      3. The electrical key is in the cabin or luggage compartment.
      4. Vehicle speed is above 0 km/h (0 mph).
      Combination Meter
      1. Multi-information Display
      Warning:
      Information is displayed alternately on the combination meter:
      1. "Shift to P Range"
      2. "Key is not Detected"
      "Shift to P Range" warning is stopped when one of the following conditions is met:
      1. The engine switch is off.
      2. Vehicle speed is above 0 km/h (0 mph).
      3. The shift lever position is P.
      "Key is not Detected" warning is stopped when either of the following conditions is met:
      1. The engine switch is off.
      2. The electrical key is in cabin or luggage compartment.
      Wireless Door Lock Buzzer
      Warning:
      Continuous sound
      The warning is stopped when one of the following conditions is met:
      1. The engine switch is off.
      2. The shift lever position is P.
      3. The electrical key is in the cabin or luggage compartment.
      4. Vehicle speed is above 0 km/h (0 mph).

  3. Situation B
    There are 2 patterns for situation B.
    Pattern 1: In situation B, the door is opened and the user tries to leave the vehicle.
    Then the user holds the electrical key and tries to move away from the vehicle.
    Pattern 2: Then the user tries to use the entry lock and presses the lock switch.
    In these situations, the following control is performed:

    1. Pattern 1
      Possible Effects without Warning
      Vehicle theft, engine cannot be restarted
      Warning Condition
      The certification ECU gives warning when all following conditions are satisfied:
      1. The shift lever position is P.
      2. The engine switch is not off.
      3. The driver side door is opened and closed.
      4. The electrical key is not in the cabin or luggage compartment.
      Combination Meter
      1. Buzzer
      Warning:
      Sounds once
      Combination Meter
      1. Multi-information Display
      Warning:
      Information is displayed on the combination meter:
      1. "Key is not Detected"
      "Key is not Detected" warning is stopped when either of the following conditions is met:
      1. The engine switch is off.
      2. The electrical key is in the cabin or luggage compartment.
      Wireless Door Lock Buzzer
      Warning:
      Sounds 3 times
      The warning is stopped when either of the following conditions is met:
      1. The engine switch is off.
      2. The electrical key is in the cabin or luggage compartment.
    1. Pattern 2
      Possible Effects without Warning
      Vehicle theft
      Warning Condition
      The certification ECU gives warning when all following conditions are satisfied:
      1. The shift lever position is P.
      2. The engine switch is not off.
      3. All doors are closed.
      4. The lock switch is "ON".
      5. The electrical key is not in the cabin or luggage compartment.
      Combination Meter
      1. Buzzer
      -
      Combination Meter
      1. Multi-information Display
      -
      Wireless Door Lock Buzzer
      Warning:
      Sounds for 2 seconds

  4. Situation C
    In this situation, the following control is performed:

    Possible Effects without Warning
    Engine cannot be restarted
    Warning Condition
    The certification ECU gives warning when all following conditions are satisfied:
    1. The engine switch is not off.
    2. Door other than driver side door is opened and closed.
    3. Vehicle speed is 0 km/h (0 mph).
    4. The electrical key is not in the cabin or luggage compartment.
    Combination Meter
    1. Buzzer
    Warning:
    Sounds once
    Combination Meter
    1. Multi-information Display
    Warning:
    Information is displayed on the combination meter:
    1. "Key is not Detected"
    "Key is not Detected" warning is stopped when one of the following conditions is met:
    1. The engine switch is off.
    2. Vehicle speed is above 0 km/h (0 mph).
    3. The electrical key is in the cabin or luggage compartment.
    Wireless Door Lock Buzzer
    Warning:
    Sounds 3 times
    The warning is stopped when one of the following conditions is met:
    1. The engine switch is off.
    2. Vehicle speed is above 0 km/h (0 mph).
    3. The electrical key is in the cabin or luggage compartment.

  5. Situation D
    In this situation, the following control is performed:

    Possible Effects without Warning
    Confuses the user
    Warning Condition
    The certification ECU gives warning when both following conditions are satisfied:
    1. The engine switch is OFF → ON.
    2. The electrical key is not in the cabin.
    Combination Meter
    1. Buzzer
    Warning:
    Sounds once
    Combination Meter
    1. Multi-information Display
    Warning:
    Information is displayed on the combination mete for 8 seconds:
    1. "Key is not Detected"
    Wireless Door Lock Buzzer
    -

  6. Situation E
    In this situation, the following control is performed:

    Possible Effects without Warning
    Vehicle theft
    Warning Condition
    The certification ECU gives warning when all following conditions are satisfied:
    1. The engine switch is off.
    2. All doors are closed.
    3. The lock switch is "ON".
    4. The electrical key is in the cabin or luggage compartment.
    Combination Meter
    1. Buzzer
    -
    Combination Meter
    1. Multi-information Display
    -
    Wireless Door Lock Buzzer
    Warning:
    Sounds for 2 seconds

  7. Situation F
    In this situation, the following control is performed:

    Possible Effects without Warning
    Smart entry and start system does not function
    Warning Condition
    The certification ECU gives warning when all following conditions are satisfied:
    1. The engine switch is turned off after being left on (IG) for over 20 minutes.
    2. The electrical key battery voltage is low.
    3. The electrical key is in the cabin.
    Combination Meter
    1. Buzzer
    Warning:
    Sounds once
    Combination Meter
    1. Multi-information Display
    Warning:
    Information is displayed on the combination meter for 5 seconds:
    1. "Low Key Battery"
    Wireless Door Lock Buzzer
    -

  8. Situation G
    There are two patterns for situation G.

    1. Pattern 1: When the driver's door is open, the driver changes the power source mode to ACC and attempts to leave the vehicle.
    2. Pattern 2: When the driver's door is open, the driver changes the power source mode from ON to OFF and attempts to leave the vehicle.
    In these situations, the following control is performed:
    Pattern 1 and Pattern 2 
    Possible Effects without Warning
    Vehicle theft
    Warning Condition
    The warning is activated when either of the following conditions is met:
    1. The engine switch is on (ACC) and the driver door is opened.
    2. The engine switch is off, the steering is unlocked, and the driver door is opened.
    Combination Meter
    1. Buzzer
    Continues to sound at short and even intervals
    Combination Meter
    1. Multi-information Display
    -
    Wireless Door Lock Buzzer
    -
    Engine Switch Indicator Light
    -
    Warning Stop Condition
    The warning is stopped when one of the following conditions is met:
    1. The engine switch is off.
    2. The driver side door is closed.
    3. The engine switch is off and the steering is locked.

  9. Situation H
    The lock switch on the door outside handle is pressed to perform entry lock with a door open. In this situation, the following control is performed:

    Possible Effects without Warning
    Vehicle theft
    Warning Condition
    The warning is activated when all of the following conditions are met:
    1. The engine switch is off.
    2. Any doors are opened.
    3. The entry lock button on the outer door handle is operated.
    Combination Meter
    1. Buzzer
    -
    Combination Meter
    1. Multi-information Display
    -
    Wireless Door Lock Buzzer
    Warning:
    Continuous sound
    Engine Switch Indicator Light
    -
    Warning Stop Condition
    The warning is stopped when one of the following conditions is met:
    1. The engine switch is off.
    2. All doors are closed.
    3. Wireless door lock remote function is unlocked.
    4. Entry unlock is operated.
    5. 10 seconds have elapsed since the wireless door lock buzzer was activated.

  10. Situation I
    The luggage compartment door is closed with the electrical key left in the luggage compartment. In this situation, the following control is performed:

    Possible Effects without Warning
    Vehicle theft
    Warning Condition
    The warning is activated when all of the following conditions are met:
    1. Vehicle speed is less than 3.1 km/h (5 mph).
    2. All doors are closed.
    3. Entry luggage compartment open function is available.
    Combination Meter
    1. Buzzer
    -
    Combination Meter
    1. Multi-information Display
    -
    Wireless Door Lock Buzzer
    Sounds for 2 seconds
    Warning Stop Condition
    -

  11. Situation J
    The steering lock cannot be released. In this situation, the following control is performed:

    Possible Effects without Warning

    Warning Condition
    The steering lock cannot be released, thus the engine is prevented from starting.
    Combination Meter
    1. Buzzer
    -
    Combination Meter
    1. Multi-information Display
    Warning:
    Information is displayed on the combination meter: Displayed for 15 seconds (and then automatically turned off)
    1. "S/T is not Unlocked"
    Combination Meter
    1. Master Warning Light
    Flashes
    Wireless Door Lock Buzzer
    -
    Engine Switch Indicator Light
    The green indicator blinks at 1-second intervals (goes off automatically in 15 seconds).
    Warning Stop Condition
    The engine switch is pressed while the steering wheel is turned left and right, and the steering lock is successfully released.

  12. Situation K
    A malfunction of the steering lock ECU is detected. In this situation, the following control is performed:

    Possible Effects without Warning
    Vehicle theft
    Warning Condition
    A malfunction of the steering lock ECU is detected.
    Combination Meter
    1. Buzzer
    -
    Combination Meter
    1. Multi-information Display
    Warning:
    Information is displayed on the combination meter:
    1. "Check S/T Lock"
    Combination Meter
    1. Master Warning Light
    Flashes
    Wireless Door Lock Buzzer
    -
    Engine Switch Indicator Light
    The amber indicator blinks at 2-second intervals.
    Warning Stop Condition
    The steering lock ECU returns to normal.

  13. Situation L
    A malfunction of the main body ECU (instrument panel J/B) is detected. In this situation, the following control is performed:

    Possible Effects without Warning
    Vehicle theft
    Warning Condition
    A malfunction in the main body ECU is detected.
    Combination Meter
    1. Buzzer
    -
    Combination Meter
    1. Multi-information Display
    -
    Combination Meter
    1. Master Warning Light
    -
    Wireless Door Lock Buzzer
    -
    Engine Switch Indicator Light
    The amber indicator blinks at 2-second intervals.
    Warning Stop Condition
    The main body ECU (instrument panel J/B) returns to normal.

  14. Situation M
    A warning message appears on the meter when the driver does not follow the proper procedure to start the vehicle.
    In this situation, the following control is performed:

    Possible Effects without Warning
    Vehicle theft
    Warning Condition
    The warning is activated when all of the following conditions are met:
    1. The power source is in a mode other than "ON".
    2. Any doors are closed and opened.
    3. The power source is changed from OFF to ACC more than once with the engine off and brake pedal not depressed.
    Combination Meter
    1. Buzzer
    -
    Combination Meter
    1. Multi-information Display
    Warning:
    Information is displayed alternately on the combination meter:
    1. "When Starting the Engine Depress the Brake Pedal"
    Combination Meter
    1. Master Warning Light
    -
    Wireless Door Lock Buzzer
    -
    Engine Switch Indicator Light
    -
    Warning Stop Condition
    The warning is stopped when either of the following conditions is met:
    1. 10 seconds have elapsed since a warning message was displayed.
    2. The engine switch is pushed with the brake pedal depressed.


BATTERY SAVING
  1. Vehicle Battery Saving Function
    In the smart entry and start system, signals are emitted outside the vehicle at prescribed intervals (0.25 seconds) when the doors are locked. Therefore, the vehicle battery could be drained if the vehicle remains parked for a long time. For this reason, the controls listed below are carried out:

    Condition
    Control
    Both conditions below are met for 5 days:
    1. Electrical key is not in detection area.
    2. Touch sensor or lock switch operation is not performed.
    Signal transmission interval is extended from 0.25 to 0.75 seconds.
    Both conditions below are met for 14 days:
    1. Electrical key is not in detection area.
    2. Touch sensor or lock switch operation is not performed.
    Automatically deactivates the smart entry and start system
    Reinstatement Conditions
    1. A wireless door lock control signal (lock, unlock) is input and the ID code matches.
    2. A user carries the electrical key and pushes a lock switch on an outside door handle.
    3. A door is locked or unlocked by the mechanical key.

  2. Electrical Key Battery and Vehicle Battery Saving Function
    In the smart entry and start system, if the electrical key is constantly located within the vehicle exterior detection area of the doors, the system maintains periodic communication with the electrical key. Therefore, if the vehicle remains parked in that state for a long time, the electrical key battery and the vehicle battery could be drained. For this reason, if this state continues longer than 10 minutes, the smart entry and start system automatically becomes deactivated.
    Reinstatement Conditions

    1. A wireless door lock control signal (lock, unlock) is input and the ID code matches.
    2. A user carries the electrical key and pushes a lock switch on an outside door handle.
    3. A door is locked or unlocked by the mechanical key.

← SYSTEM DIAGRAM (from Oct 2006)SYSTEM DESCRIPTION (from Jun 2009) →