TERMINALS OF ECU
System information · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
- NOTICE:
- Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- HINT:
- Operating the engine switch, any other switches, or a door triggers related ECU and sensor communication on the CAN.
- This communication will cause the resistance value to change.
- NOTICE:
- This section describes the standard CAN values for all CAN related components.
| JUNCTION CONNECTOR FOR CAN NO. 1 BUS |
CAN No. 1 J/C


CAN No. 1 J/C Connector ("A" side, with earth terminal)
Connector Color
Color (CAN-H Side)
Color (CAN-L Side)
CAN No. 1 Bus Main Wire (E42)
White
B
W
Center Airbag Sensor Assembly (E45)
Black
B
W
CAN No. 1 J/C Connector ("B" side, without earth terminal)
Connector Color
Color (CAN-H Side)
Color (CAN-L Side)
Yaw Rate Sensor (E46)
Blue
B
W
A/C Amplifier (E47)
Gray
B
W
Combination Meter (E43)
White
B
W
Main Body ECU (E44)
Black
B
W
CAN No. 4 J/C (REAR OF THE VEHICLE)


Wiring color: Terminal
Wiring Color
Destination
A40-1 (CANH)
B
ECM (CANH)
A40-7 (CANL)
W
ECM (CANL)
A40-2 (CANH)
B
Skid Control ECU (CANH)
A40-8 (CANL)
W
Skid Control ECU (CANL)
CAN No. 4 J/C (FRONT OF THE VEHICLE)


*: with AFSWiring color: Terminals
Wiring Color
Destination
E41-1 (CANH)
B
Gateway ECU (CANH) *
E41-7 (CANL)
W
Gateway ECU (CANL) *
E41-2 (CANH)
B
DLC3 (CANH)
E41-8 (CANL)
W
DLC3 (CANL)
E41-3 (CANH)
B
Steering Angle Sensor (CANH)
E41-9 (CANL)
W
Steering Angle Sensor (CANL)
E41-4 (CANH)
B
CAN No. 1 J/C (CANH)
E41-10 (CANL)
W
CAN No. 1 J/C (CANL)
The connection diagram of the components which are connected to the CAN J/C


| JUNCTION CONNECTOR FOR CAN MS BUS |
CAN No. 3 J/C


Wiring color: CAN No. 3 J/C Connector ("A" side, with earth terminal)
Connector Color
Color (CAN-H Side)
Color (CAN-L Side)
Certification ECU (O34)
Gray
L
W
Clearance Warning ECU (O32)
Blue
L
W
CAN MS Bus Main Wire (O33)
White
L
W
CAN No. 5 J/C


Wiring color: Terminal
Wiring color
Destination
E81-11 (CANH)
L
Main Body ECU (CANP)
E81-22 (CANL)
W
Main Body ECU (CANN)
E81-9 (CANH)
L
Seat Position Control ECU (CANH)
E81-20 (CANL)
W
Seat Position Control ECU (CANL)
E81-8 (CANH)
L
Outer Mirror Control ECU (CAN)
E81-19 (CANL)
W
Outer Mirror Control ECU (CGND)
E81-10 (CANH)
L
CAN No. 3 J/C (CANH)
E81-21 (CANL)
W
CAN No. 3 J/C (CANL)
| JUNCTION CONNECTOR FOR CAN NO. 2 BUS |
CAN No. 2 J/C


Wiring color: CAN No. 2 J/C Connector ("A" Side, with earth terminal)
Connector Color
Wire Color (CAN-H)
Wire Color (CAN-L)
CAN No. 2 Bus Main Wire (E79)
White
R
W
AFS ECU (E80)
Black
R
W
| DLC3 |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E10-6 (CANH) - E10-14 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E10-6 (CANH) - E10-4 (CG)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E10-14 (CANL) - E10-4 (CG)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E10-6 (CANH) - E10-16 (BAT)
B - L
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E10-14 (CANL) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| SKID CONTROL ECU WITH ACTUATOR |
Disconnect the connector from the skid control ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
A26-35 (CANH) - A26-14 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
A26-35 (CANH) - A26-4 (GND1)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A26-14 (CANL) - A26-4 (GND1)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A26-35 (CANH) - A26-3 (+BS)
B - L
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
A26-14 (CANL) - A26-3 (+BS)
W - L
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| STEERING ANGLE SENSOR |
Disconnect the connector from the steering angle sensor.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E17-10 (CANH) - E17-9 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E17-10 (CANH) - E17-2 (ESS)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E17-9 (CANL) - E17-2 (ESS)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E17-10 (CANH) - E17-3 (BAT)
B - W
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E17-9 (CANL) - E17-3 (BAT)
W - W
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| YAW RATE SENSOR |
Disconnect the connector from the yaw rate sensor.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E34-2 (CANH) - E34-3 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E34-2 (CANH) - E34-4 (GND)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E34-3 (CANL) - E34-4 (GND)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E34-2 (CANH) - E10-16 (BAT)
B - L
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E34-3 (CANL) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| CENTER AIRBAG SENSOR |
Disconnect the connector from the center airbag sensor.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E30-13 (CANH) - E30-22 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E30-13 (CANH) - E30-25 (E1)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E30-22 (CANL) - E30-25 (E1)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E30-13 (CANH) - E10-16 (BAT)
B - L
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E30-22 (CANL) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| ECM |
Disconnect the connector from the ECM.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Condition
Specified Value
A24-41 (CANH) - A24-49 (CANL)
Engine switch off
108 to 132 Ω
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
A24-41 (CANH) - A24-49 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
108 to 132 Ω
A24-41 (CANH) - C58-81 (E1)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A24-49 (CANL) - C58-81 (E1)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A24-41 (CANH) - A24-20 (BATT)
B - Y
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
A24-49 (CANL) - A24-20 (BATT)
W - Y
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| AIR CONDITIONING AMPLIFIER |
Disconnect the connector from the air conditioning amplifier.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E38-11 (CANH) - E38-12 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E38-11 (CANH) - E38-14 (GND)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E38-12 (CANL) - E38-14 (GND)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E38-11 (CANH) - E38-21 (B)
B - GR
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E38-12 (CANL) - E38-21 (B)
W - GR
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| COMBINATION METER |
Disconnect the connector from the combination meter.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Condition
Specified Value
F1-17 (CANH) - F1-18 (CANL)
Engine switch off
108 to 132 Ω
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
F1-17 (CANH) - F1-18 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
108 to 132 Ω
F1-17 (CANH) - F1-12 (E2)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
F1-18 (CANL) - F1-12 (E2)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
F1-17 (CANH) - F1-2 (B2)
B - R
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
F1-18 (CANL) - F1-2 (B2)
W - R
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| CERTIFICATION ECU |
Disconnect the connector from the certification ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Condition
Specified Value
E58-27 (CANH) - E58-28 (CANL)
Engine switch off
108 to 132 Ω
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E58-27 (CANH) - E58-28 (CANL)
L - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
108 to 132 Ω
E58-27 (CANH) - E58-17 (E)
L - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E58-28 (CANL) - E58-17 (E)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E58-27 (CANH) - E58-1 (+B)
L - W
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E58-28 (CANL) - E58-1 (+B)
W - W
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| MAIN BODY ECU (INSTRUMENT PANEL J/B) |
Disconnect the connector from the main body ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Condition
Specified Value
E8-16 (CANP) - E8-15 (CANN)
Engine switch off
108 to 132 Ω
Measure the resistance according to the value(s) in the table below.


- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E8-5 (CANH) - E8-6 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E8-5 (CANH) - E10-4 (CG)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-6 (CANL) - E10-4 (CG)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-5 (CANH) - E10-16 (BAT)
B - L
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E8-6 (CANL) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E8-16 (CANP) - E8-15 (CANN)
L - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
108 to 132 Ω
E8-16 (CANP) - E10-4 (CG)
L - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-15 (CANN) - E10-4 (CG)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-16 (CANP) - E10-16 (BAT)
L - L
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E8-15 (CANN) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| GATEWAY ECU (w/ AFS) |
Disconnect the connector from the gateway ECU.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Condition
Specified Value
E70-13 (CA2H) - E70-12 (CA2L)
Engine switch off
108 to 132 Ω
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E70-16 (CA1H) - E70-15 (CA1L)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E70-16 (CA1H) - E70-4 (GND)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E70-15 (CA1L) - E70-4 (GND)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E70-16 (CA1H) - E70-2 (BATT)
B - W
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E70-15 (CA1L) - E70-2 (BATT)
W - W
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E70-13 (CA2H) - E70-12 (CA2L)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
108 to 132 Ω
E70-13 (CA2H) - E70-4 (GND)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E70-12 (CA2L) - E70-4 (GND)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E70-13 (CA2H) - E70-2 (BATT)
B - W
HIGH-level CAN bus wire - Battery positive
Engine switch off
1 MΩ or higher
E70-12 (CA2L) - E70-2 (BATT)
W - W
LOW-level CAN bus wire - Battery positive
Engine switch off
1 MΩ or higher
| OUTER MIRROR CONTROL ECU (w/ Seat Position Memory) |
Disconnect the connector from the outer mirror control ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E85-1 (CAN) - E85-21 (CGND)
L - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E85-1 (CAN) - E86-9 (GND)
L - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E85-21 (CGND) - E86-9 (GND)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E85-1 (CAN) - E86-3 (B)
L - W-R
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E85-21 (CGND) - E86-3 (B)
W - W-R
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| SEAT POSITION CONTROL ECU (Front RH Side) (w/ Seat Position Memory) |
Disconnect the connector from the seat position control ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
T21-5 (CANH) - T21-1 (CANL)
L - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
T21-5 (CANH) - T20-1 (GND)
L - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
T21-1 (CANL) - T20-1 (GND)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
T21-5 (CANH) - T20-5 (+B)
L - G
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
T21-1 (CANL) - T20-5 (+B)
W - G
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| AFS ECU (w/ Adaptive Front-Lighting System) |
Disconnect the connector from the AFS ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
A61-12 (MPX1) - A61-13 (MPX2)
R - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
A61-12 (MPX1) - A61-22 (EIS)
R - W
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A61-13 (MPX2) - A61-22 (EIS)
W - W
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A61-12 (MPX1) - E10-16 (BAT)
R - L
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
A61-13 (MPX2) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
| CLEARANCE WARNING ECU |
Disconnect the connector from the clearance warning ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
O30-3 (R1) - O30-5 (R2)
L - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
O30-3 (R1) - O30-17 (E)
L - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
O30-5 (R2) - O30-17 (E)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
O30-3 (R1) - E10-16 (BAT)
L - L
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
O30-5 (R2) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher