DIAGNOSIS SYSTEM
Troubleshooting · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| DESCRIPTION |
DIAGNOSTIC SYSTEM
When troubleshooting a vehicle with a diagnostic system, the only difference from the usual troubleshooting procedure is connecting the intelligent tester to the vehicle and reading various data output from the vehicle's steering lock ECU.
The steering lock ECU records DTCs when the computer detects a malfunction in the computer itself or in system circuits.
To check the DTCs, connect the intelligent tester to the DLC3 on the vehicle. The intelligent tester enables the DTCs to be cleared, the indicators to be activated, and the DATA LIST to be checked.The steering lock ECU diagnosis information cannot be read directly from the steering lock ECU by the tester. The diagnosis information from the steering lock ECU is transmitted to the tester via the certification ECU to the tester using the controller area network (CAN).
| CHECK DLC3 |
The certification ECU uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

Symbols (Terminal No.)
Terminal Description
Condition
Specified Condition
SIL (7) - SG (5)
Bus "+" line
During transmission
Pulse generation
CG (4) - Body ground
Chassis ground
Always
Below 1 Ω
SG (5) - Body ground
Signal ground
Always
Below 1 Ω
BAT (16) - Body ground
Battery positive
Always
11 to 14 V
CANH (6) - CANL (14)
CAN bus line
Engine Switch off*
54 to 69 Ω
CANH (6) - CG (4)
HIGH-level CAN bus line
Engine Switch off*
200 Ω or higher
CANL (14) - CG (4)
LOW-level CAN bus line
Engine Switch off*
200 Ω or higher
CANH (6) - BAT (16)
HIGH-level CAN bus line
Engine Switch off*
6 kΩ or higher
CANL (14) - BAT (16)
LOW-level CAN bus line
Engine Switch off*
6 kΩ or higher
- NOTICE:
- *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches or the doors.
Connect the cable of the intelligent tester to the DLC3, turn the engine switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.

- If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
- If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.
- If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
| WARNING FUNCTION OF ENGINE SWITCH INDICATOR |
The steering lock ECU blinks the LED indicator of the engine switch when any of the following problems occurs in the system:

Detection Item
Indicator Light Blink Pattern
Indication Status
Countermeasure
Steering lock is still not released
- Blinks green at 1-second intervals
- Goes off 15 seconds after blinking starts
The motor operates to release the steering lock, but the steering lock cannot be released (e.g. the lock bar is stuck in the steering column).
Push the engine switch while turning the steering wheel left or right.
Malfunction in smart entry and start system
- Blinks amber at 2-second intervals
- Goes off 15 seconds after the engine switch is turned off while blinking
- There is a short in the devices activating the motor.
- There is a problem in the steering lock ECU or main body ECU.
Troubleshoot by following "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here).
- Blinks green at 1-second intervals
| WARNING FUNCTION OF COMBINATION METER |
The steering lock ECU displays a warning on the combination meter when any of the following problems occurs in the system.
Detection Item
Display
Indication Status
Countermeasure
Steering lock is still not released
"S/T IS NOT UNLOCKED" - Goes off 15 seconds after blinking starts
The motor operates to release the steering lock, but the steering lock cannot be released (e.g. the lock bar is stuck in the steering column).
Push the engine switch while turning the steering wheel left or right.
Malfunction in smart entry and start system
"CHECK S/T LOCK" - Goes off 15 seconds after the engine switch is turned off while blinking
- There is a short in the devices activating the motor.
- There is a problem in the steering lock ECU or main body ECU.
Troubleshoot by following "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here).
- Goes off 15 seconds after blinking starts