2006-2011 Camry Aurion · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL RING PIN

  1. Using a plastic hammer, tap in the ring pin.

    A112251E02

    Standard protrusion:
    Item
    Protrusion
    Pin A
    6 mm (0.236 in.)
    Pin B
    5 mm (0.197 in.)


2. INSTALL STUD BOLT

  1. Install the stud bolts as shown in the illustration.

    A142083E01

    Torque:
    Stud Bolt A:
    22 N*m{ 220 kgf*cm , 16 ft.*lbf }
    Stud Bolt B:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Stud Bolt C:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
    Stud Bolt D:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


3. INSTALL STRAIGHT PIN

  1. Using a plastic hammer, tap in the straight pin.

    A112252E03

    Standard protrusion:
    Item
    Protrusion
    Pin A
    8 mm (0.315 in.)
    Pin B
    7.5 mm (0.295 in.)
    Pin C
    12 mm (0.472 in.)
    Pin D
    5 mm (0.197 in.)


4. INSTALL PISTON

  1. A128244
    Using a screwdriver, install a new snap ring at one end of the piston pin hole.

    HINT:
    Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.

  1. Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).

  1. A138300E01
    Align the front marks of the piston and connecting rod, and push in the piston with your thumb.

  1. Using a screwdriver, install a new snap ring on the other end of the piston pin hole.

    HINT:
    Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.

  1. A107551
    Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


5. INSTALL PISTON RING SET
  1. Install the oil ring expander and 2 oil ring rails by hand.

  1. A138301E02
    Using a piston ring expander, install the 2 compression rings so that the paint marks are positioned as shown in the illustration.

    NOTICE:
    Install the compression ring No. 2 with the code mark (2N or 2R) facing upward.

  1. A132480E01
    Position the piston rings so that the ring ends are as shown in the illustration.


6. INSTALL CRANKSHAFT BEARING

  1. A053015
    Install the upper bearing with an oil groove on the cylinder block.

    NOTICE:
    Do not apply engine oil to the bearings and the contact surfaces.


7. INSTALL NO. 2 CRANKSHAFT BEARING

  1. A063909E01
    Install the lower bearing onto the bearing cap.

    NOTICE:
    Clean the backside of the bearing and the bearing surface of the connecting rod. The surface should be free of dust and oil.


8. INSTALL UPPER CRANKSHAFT THRUST WASHER

  1. A013501E01
    Install the 2 thrust washers under the No. 3 journal of the cylinder block with the oil grooves facing outward.

  1. Apply engine oil to the crankshaft thrust washer.


9. INSTALL CRANKSHAFT
  1. Apply engine oil to the upper bearing and install the crankshaft on the cylinder block.

  1. Apply engine oil to the lower bearing.

  1. A128241E01
    Examine the front marks and install the bearing caps on the cylinder block.

  1. Apply a light coat of engine oil to the threads and under the bearing cap bolts.

  1. Install the crankshaft bearing cap bolts.

    NOTICE:
    The main bearing cap bolts are tightened in 2 progressive steps.

  1. Step 1

    1. A128235E02
      Install and uniformly tighten the 10 main bearing cap bolts in the sequence shown in the illustration.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    2. A128235E02
      Further tighten the 10 main bearing cap bolts in the sequence shown in the illustration.

      Torque:
      40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Step 2

    1. A050671E10
      Mark the front of the bearing cap bolts with paint.

    2. Further tighten the bearing cap bolts by 90° in the numerical order shown in the previous illustration.

  1. Check that the paint mark is now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.

  1. Check the crankshaft thrust clearance (Click here).


10. INSTALL CONNECTING ROD BEARING

  1. A128248E01
    Align the bearing claw with the groove of the connecting rod or connecting cap.

    NOTICE:
    Do not apply engine oil to the bearings or the contact surfaces.


11. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

NOTICE:
The connecting rod cap bolts are tightened in 2 progressive steps.

  1. Apply engine oil to the cylinder walls, the pistons, and the surfaces of connecting rod bearings.

  1. A132480E01
    Check the position of the piston ring ends.

  1. A143962E01
    Using a piston ring compressor, push the correctly numbered piston and connecting rod assemblies into each cylinder with the front mark of the piston facing forward.

    NOTICE:
    Match the numbered connecting rod cap with the connecting rod.

  1. A052515E01
    Check that the protrusion of the connecting rod cap is facing in the correct direction.

  1. Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.

  1. Install the connecting cap bolts.

    NOTICE:
    The connecting cap bolts should be tightened in 2 progressive steps.

  1. Step 1

    1. A013397
      Install and alternately tighten the bolts of the connecting rod cap in several steps.

      Torque:
      25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Step 2

    1. A101478E03
      Mark the front of the connecting rod cap bolts with paint.

    2. Further tighten the cap bolts by 90° as shown in the illustration.

  1. Check that the crankshaft turns smoothly.

  1. Check the connecting rod thrust clearance (Click here).


12. INSTALL STIFFENING CRANKCASE ASSEMBLY

  1. A128206
    Place a new O-ring on the cylinder block, as shown in the illustration.

  1. Temporarily tighten the pulley set bolt.

  1. A366990E01
    Turn the crankshaft so that the key groove is facing downward.

    HINT:
    Make sure that the timing mark on the balanceshaft drive gear is positioned as shown in the illustration.

  1. A128254E01
    Apply seal packing in a continuous bead (diameter: 2.5 to 3.0 mm (0.098 to 0.118 in.)) to the places shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Ensure that no oil packing enters the oil path. The oil path has a groove to catch excess seal packing. Do not apply seal packing to the oil path side of the groove or to the groove itself, or seal packing may enter the oil path.
    3. Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
    4. Do not add engine oil for at least 2 hours after the installation.

  1. Install the stiffening crankcase assembly to the cylinder block.

  1. A128202E04
    Temporarily install the crankcase with the 11 bolts.

    Bolt length:
    Item
    Length
    Bolt A
    122 mm (4.803 in.)
    Bolt B
    45 mm (1.772 in.)

  1. A128202E05
    Uniformly tighten the 11 bolts in the sequence shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

  1. Wipe off any excess seal packing with a clean piece of cloth.


13. INSTALL NO.1 BALANCESHAFT BEARING

  1. A366989E01
    Clean each No.1 balanceshaft bearing installation surface and inner and outer surfaces of the No.1 balanceshaft bearing.

    NOTICE:
    Do not apply engine oil to the No.1 balanceshaft bearing installation surface or the outer surface of the No.1 balanceshaft bearing.

  1. Align the claw of the No.1 balanceshaft bearing with the groove of the balanshaft housing and install 8 no.1 ballanceshaft bearings.

  1. Apply engine oil to the inner surface of the No.1 balanceshaft bearings.


14. INSTALL NO. 1 AND NO. 2 BALANCESHAFT SUB-ASSEMBLY

  1. A366991E01
    Turn the No.1 driven gear counterclockwise until it stops, then align the matchmark of the No.1 driven gear with that of the No.2 driven gear.

  1. A366992E01
    Install the No.1 balanceshaft with the timing mark positioned as shown in illustration. [*1]

    HINT:
    (A) is not a timing mark.

  1. A366993E01
    Install the No.2 balanceshaft with the timing mark positioned as shown in the illustration.

NOTICE:
Make sure that the key groove of the crankshaft and timing mark of the balanceshafts are positioned as shown in the illustration.


A366994E01

HINT:
(A) is not a timing mark.

  1. Apply a light coat of engine oil under the heads of the balanceshaft housing bolts.

  1. Install the balanceshaft housing bolts.

    NOTICE:
    The balanceshaft housing bolts are tightened in 2 progressive steps.

  1. Step 1

    1. A128197E04
      Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

      Torque:
      22 N*m{ 220 kgf*cm , 16 ft.*lbf }

  1. Step 2

    1. A146261E01
      Mark the front side of each balanceshaft housing bolt head with paint.

    2. Further tighten the bolts by 90° as shown in the illustration.

      NOTICE:
      Check that the paint marks are now at a 90° angle to the front.

  1. Turn the crankshaft 360° and check that the timing marks of the balanceshafts are positioned as shown in the illustraion with the key groove of the crankshaft facing downward.

    A366995E01

NOTICE:
If the timing marks are not positioned as shown in the illustration, perform the procedure from step [*1] again.

HINT:
(A) is not a timing mark.

  1. Remove the pulley set bolt.


15. INSTALL OIL PUMP ASSEMBLY

  1. A128253
    Install a new gasket and oil pump with the 3 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


16. INSTALL ENGINE REAR OIL SEAL
  1. Apply MP grease to a new oil seal lip.

    NOTICE:
    Wipe off extra grease on the crankshaft.

  1. A128212E01
    Using SST and a hammer, evenly tap the oil seal until its surface is flush with the rear oil seal retainer edge.
    SST
    09223-15030  
    09950-70010   (09951-07100)

    NOTICE:
    Keep the lip free from foreign materials.


17. INSTALL OIL CONTROL VALVE FILTER
  1. Check that no foreign matter is on the mesh part of the filter.

  1. A128210E01
    Using an 8 mm socket hexagon wrench, install a new gasket and the oil control valve filter with the screw plug.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter.


18. INSTALL CYLINDER HEAD GASKET

  1. A126929E01
    Place a new gasket on the cylinder block surface with the Lot No. stamp facing upward.

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Make sure that the gasket is installed in the correct direction.


19. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
The cylinder head set bolts are tightened in 2 progressive steps.

  1. Apply a light coat of engine oil to the bolt threads and the area beneath the bolt heads that come in contact with the washers.

  1. Install the bolts and plate washers to the cylinder head.

    NOTICE:
    Do not drop the washers into the cylinder head.

  1. F050595E06
    Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

  1. A098364E01
    Mark the front side of the cylinder head set bolt with paint.

  1. Retighten the cylinder head set bolts 90° in the order shown in the illustration.

  1. Check that the paint mark is now at a 90° angle to the front.


20. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A090053E03
    Apply a light coat of engine oil to a new O-ring, then install it onto the camshaft timing oil control valve.

  1. A128171
    Install the camshaft timing oil control valve with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


21. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

  1. A098365E02
    Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned, as shown in the illustration.

  1. Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.

    NOTICE:
    Be sure not to turn the camshaft timing gear to the retard angle side (the right angle).

  1. Check that there is no clearance between the gear and camshaft.

  1. Tighten the flange bolt with the camshaft timing gear fixed in place.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Check that the camshaft timing gear can move to the retard angle side (the right direction) and is locked in the most retarded position.


22. INSTALL CAMSHAFT TIMING SPROCKET

  1. A032167
    Clamp the camshaft in a vise.

  1. Tighten the flange bolt with the camshaft timing sprocket fixed.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }


23. INSTALL NO. 1 CAMSHAFT BEARING

  1. A128191
    Install the No. 1 camshaft bearing.


24. INSTALL NO. 2 CAMSHAFT BEARING

  1. A128879
    Install the No. 2 camshaft bearing.


25. INSTALL CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the camshaft.

  1. A098177E03
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A098177E06
    Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    No. 1 bearing cap:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }
    No. 3 bearing cap:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


26. INSTALL NO. 2 CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the No. 2 camshaft.

  1. A098174E05
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A098174E07
    Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    No. 2 bearing cap:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }
    No. 3 bearing cap:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


27. INSTALL KEYS

  1. A131498
    Install the 2 keys.


28. INSTALL NO. 2 CHAIN SUB-ASSEMBLY

  1. B011424
    Set the crankshaft key into the left horizontal position.

  1. Turn the drive shaft so that the cutout faces upward.

  1. A094198E07
    Align the yellow mark links with the timing marks of each gear as shown in the illustration.

  1. Install the gears onto the crankshaft and oil pump shaft with the chain on the gears.

  1. Temporarily tighten the oil pump drive shaft gear with the nut.

  1. A090851E03
    Insert the damper spring into the adjusting hole, and then install the chain tensioner plate with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. A052512E02
    Align the adjusting hole of the oil pump drive shaft gear with the groove of the oil pump.

  1. Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft gear to lock the gear in position, and then tighten the nut.

    Torque:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }

  1. A036525
    Rotate the crankshaft clockwise 90°, and position the crankshaft key to face up as shown in the illustration.


29. INSTALL CRANKSHAFT TIMING SPROCKET

  1. A125374
    Install the crankshaft timing sprocket.


30. INSTALL NO. 1 CHAIN VIBRATION DAMPER

  1. A132570
    Install the chain vibration damper with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


31. INSTALL CHAIN SUB-ASSEMBLY

  1. A053018E05
    Set the No. 1 cylinder to TDC/compression.

    1. Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.

    2. A052505
      Using the crankshaft pulley bolt, turn the crankshaft to position the crankshaft key to face up as shown in the illustration.

  1. A094576E01
    Install the chain onto the crankshaft timing sprocket with the gold or pink mark link aligned with the timing mark on the crankshaft.

  1. A098369E01
    Using SST and a hammer, tap in the crankshaft timing sprocket.
    SST
    09309-37010  

  1. A098370E01
    Align the gold or yellow mark link with each timing mark located on the camshaft timing gear and sprocket, then install the chain.


32. INSTALL CHAIN TENSIONER SLIPPER

  1. A124787E01
    Install the chain tensioner slipper with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


33. INSTALL TIMING CHAIN GUIDE

  1. A125373
    Install the timing chain guide with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


34. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A124770
    Install the sensor plate with the "F" mark facing forward.


35. INSTALL TIMING CHAIN CASE OIL SEAL

  1. A128223E03
    Using SST, tap in a new oil seal until its surface is flush with the timing chain cover edge.
    SST
    09223-22010  

  1. Apply a light coat of MP grease to the lip of the oil seal.

    NOTICE:
    Keep the gap between the timing chain cover edge and the oil seal free of foreign matter.


36. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.

  1. A140776E01
    Apply seal packing (diameter: 4.0 to 4.5 mm (0.157 to 0.177 in.)) as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

  1. Apply seal packing in a continuous bead as shown in the illustration.

    A132566E03

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the chain cover within 3 minutes after applying seal packing.
    1. Do not start the engine for at least 2 hours after installing.

  1. A128178E01
    Install the timing chain cover with the 12 bolts and 2 nuts.

    Torque:
    Bolt A:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    Bolt B:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    Bolt C:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }
    Nut:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    Bolt length 
    Item
    Length
    Bolt A
    30 mm (1.18 in.) length for 10 mm head
    Bolt B
    30 mm (1.18 in.) length for 12 mm head
    Bolt C
    40 mm (1.57 in.) length for 14 mm head

  1. Using a E10 "torx" socket, install the stud bolt to the drive belt tensioner.

    Torque:
    22 N*m{ 220 kgf*cm , 16 ft.*lbf }


37. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A112212
    Install the V-ribbed belt tensioner with the bolt and nut.

    Torque:
    60 N*m{ 607 kgf*cm , 44 ft.*lbf }

    NOTICE:
    Do not lift the engine more than necessary.


38. INSTALL OIL PAN SUB-ASSEMBLY

  1. A114332E01
    Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.

  1. Apply a continuous bead of seal packing (Diameter 3.0 to 4.0 mm (0.118 to 0.157 in.)) as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil pan within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing the oil pan.

  1. Install the oil pan to the cylinder block.

  1. A114333E01
    Uniformly tighten the 12 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


39. INSTALL OIL PAN DRAIN PLUG

  1. A128176
    Install a new gasket and oil pan drain plug.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


40. INSTALL WATER PUMP ASSEMBLY
  1. Remove any old seal packing material from the contact surface.

  1. A094495E05
    Apply a continuous line of seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.2 to 2.5 mm (0.09 to 0.10 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. The parts must be set within 3 minutes after applying seal packing. Otherwise, the material must be removed and reapplied.

  1. B012052E03
    Install the water pump and clamp bracket with the 4 bolts and 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A094516
    Install the wire of the crankshaft position sensor onto the clamp bracket.

  1. Install the clamp of the crankshaft position sensor onto the water pump.


41. INSTALL WATER PUMP PULLEY

A098715E02
  1. Using SST, install the water pump pulley with the 4 bolts.

    SST
    09960-10010   (09962-01000, 09963-00700)

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


42. INSTALL CRANKSHAFT POSITION SENSOR

  1. A095436E01
    Apply a light coat of engine oil to the O-ring of the sensor.

  1. A052071E05
    Confirm that the wire harness of the sensor is placed as shown in the illustration.

  1. A063828
    Install the sensor with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A094516E01
    Install the clamp of the crankshaft position sensor onto the water pump.


43. INSTALL CRANKSHAFT PULLEY
  1. Align the pulley set key with the key groove of the pulley.

  1. A013697E03
    Using SST, hold the pulley in place and tighten the bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    180 N*m{ 1,835 kgf*cm , 133 ft.*lbf }


44. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A098376E03
    Release the ratchet pawl, then fully push in the plunger and put the hook to the pin so that the plunger is in the position shown in the illustration.

  1. A098377E03
    Install a new gasket and the chain tensioner with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    If the hook releases the plunger while the chain tensioner is being installed, set the hook again.

  1. A112204E02
    Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.

  1. A112205E02
    Turn the crankshaft clockwise, then check that the plunger is extended.


45. INSPECT VALVE CLEARANCE

  1. A098170E04
    Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (cold):
      Item
      Standard Condition
      Intake
      0.19 to 0.29 mm (0.0075 to 0.0114 in.)
      Exhaust
      0.30 to 0.40 mm (0.0118 to 0.0157 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.

  1. Turn the crankshaft 1 revolution (360°) and set the No. 4 cylinder to TDC/compression.

  1. A098171E04
    Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (cold):
      Item
      Standard Condition
      Intake
      0.19 to 0.29 mm (0.0075 to 0.0114 in.)
      Exhaust
      0.30 to 0.40 mm (0.0118 to 0.0157 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.


46. ADJUST VALVE CLEARANCE
  1. Remove the No. 2 camshaft (Click here).

  1. Remove the camshaft (Click here).

  1. Remove the valve lifters.

  1. A001082E01
    Using a micrometer, measure the thickness of the removed valve lifters.

  1. Calculate the thickness of a new lifter so that the valve clearance comes within the specified values.

    New lifter thickness:
    Item
    Specification
    Intake
    A = B + (C - 0.24 mm (0.0095 in.))
    Exhaust
    A = B + (C - 0.35 mm (0.0138 in.))

    A
    New lifter thickness
    B
    Used lifter thickness
    C
    Measured valve clearance
    CALCULATION EXAMPLE (Intake):
    1. Measured intake valve clearance = 0.40 mm (0.0158 in.)
      (Measured - Specification = Excess clearance)
      1. 0.40 mm (0.0158 in.) - 0.24 mm (0.0095 in.) = 0.16 mm (0.0063 in.)
    2. Measured used lifter thickness = 5.250 mm (0.2067 in.)
    3. New lifter thickness = 5.410 mm (0.2130 in.)
      (Excess clearance + Used lifter thickness = Ideal new lifter)
      1. 0.16 mm (0.0063 in.) + 5.250 mm (0.2067 in.) = 5.410 mm (0.2130 in.)
    4. Closest new lifter = 5.420 mm (0.2134 in.)
      1. Select No. 42 lifter

  1. A126901E01
    Select a new lifter with a thickness as close as possible to the calculated values.

    HINT:
    1. Lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 to 5.740 mm (0.1992 to 0.2260 in.).
    2. The identification number inside the valve lifters shows the value to 2 decimal places. (The illustration shows 5.420 mm (0.2134 in.))

  1. Valve lifter selection chart (intake).

    A126931E02

    New lifter thickness 
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700 (0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)
    -
    -

    Standard intake valve clearance (cold):
    0.19 to 0.29 mm (0.0075 to 0.0114 in.)

    EXAMPLE:
    The 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0157 in.). Replace the 5.250 mm (0.2067 in.) lifter with a new No. 42 lifter.

  1. Valve lifter selection chart (exhaust).

    A114356E01

    New lifter thickness 
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700 (0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)
    -
    -

    Standard exhaust valve clearance (cold):
    0.30 to 0.40 mm (0.0118 to 0.0157 in.)

    EXAMPLE:
    The 5.340 mm (0.2102 in.) lifter is installed, and the measured clearance is 0.430 mm (0.0169 in.). Replace the 5.340 mm (0.2102 in.) lifter with a new No. 42 lifter.

  1. Install the selected valve lifter.


47. INSTALL CAMSHAFT POSITION SENSOR

  1. A095434E01
    Apply a light coat of engine oil to the O-ring of the sensor.

  1. A128164
    Install the sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


48. INSTALL CYLINDER HEAD COVER GASKET

  1. A144061
    Install the gasket to the cylinder head cover.

    NOTICE:
    Remove any oil from the contact surface.


49. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing material from the contact surface.

  1. A094205E01
    Apply seal packing to the 2 locations shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes of applying seal packing.
    3. Do not add engine oil for at least 2 hours after installing the cylinder head cover.

  1. A127550E01
    Install the cylinder head cover with the 8 bolts and 2 nuts.

    Torque:
    Bolt A:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    Bolt B:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }
    Nut:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. A112210
    Install the 2 engine wires with the 2 bolts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


50. INSTALL OIL COOLER ASSEMBLY
  1. Clean the oil cooler contact surface on the cooler mounting.

  1. A124389E01
    Install a new O-ring to the oil cooler.

  1. Apply a light coat of engine oil to the threads and under the head of the union bolt.

  1. A135533
    Install the oil cooler with the plate washer, oil filter union and nut.

    Torque:
    Oil Filter Union:
    79 N*m{ 806 kgf*cm , 58 ft.*lbf }
    Nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Apply adhesive to the threads of the oil filter union.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A129331
    Install the union bolt.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


51. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.

  1. When using a torque wrench:

    1. A129850E01
      Using SST, tighten the oil filter.
      SST
      09228-06501  

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. When not using a torque wrench:

    1. A129851E01
      Using SST, tighten it an additional 3/4 turn.
      SST
      09228-06501  


52. INSTALL SPARK PLUG

  1. A128161
    Install the spark plugs.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


53. INSTALL VENTILATION VALVE SUB-ASSEMBLY

  1. A092670E03
    Apply adhesive to the threads of the ventilation valve.

  1. A128160
    Install the ventilation valve.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


54. INSTALL OIL FILLER CAP GASKET

  1. A128159
    Install the gasket to the cap.


55. INSTALL OIL FILLER CAP SUB-ASSEMBLY

  1. A128158
    Install the oil filler cap.

← INSPECTION (from Jun 2009)REASSEMBLY (Oct 2006 – May 2009) →